Руководство по эксплуатации Metra Electronics 99-7322

Краткое содержание страницы № 1

INSTALLATION INSTRUCTIONS FOR PART 99-7322
APPLICATIONS
Hyundai Azera
2006-2010
99-7322
KIT FEATURES
• DIN Radio Provision with Pocket
• ISO Radio Provision with Pocket
KIT COMPONENTS
A) Radio Housing • B) ISO Brackets • C) Trim Plate
C
B
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Wiring Harness:
• 70-1004 - Hyundai/KIA harness 2004-up
• 70-7303 - Hyundai/KIA harness 2009
A
Antenna Adapter:
• 40-KI10 KIA antenna adapter 2007-up
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Pane

Краткое содержание страницы № 2

99-7322 TABLE OF CONTENTS Dash Disassembly - Hyundai Azera 2006-2010. . . . . . . . . . . . . . . . . . . . . . . . . . . 1,2 Kit Assembly - DIN Radio Provision . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - ISO Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 *Note: Refer also to the instructions included with the a

Краткое содержание страницы № 3

99-7322 DASH DISASSEMBLY HYUNDAI AZERA 2006-2010 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Remove (1) Phillips head screw from bottom right hand corner then unclip and let the panel below the steering column hang. (Figure A) 3 Remove (1) Phillips screw from the lower left side of the radio panel behind panel removed in step 2. B (Figure B) 4 Unclip and remove the trim panel above the radio that extends across the dash to the passenger side. (Figure

Краткое содержание страницы № 4

AUTO OFF MODE A/C DUAL TEMP TEMP PASS 99-7322 DASH DISASSEMBLY HYUNDAI AZERA 2006-2010 D 5 Remove (3) Phillips screws from the top of the radio trim panel. (Figure D) 6 Remove (2) Phillips screws from under radio trim panel. (Figure E) 7 Unclip and remove the entire trim panel surrounding the radio. (Figure F) 8 Remove (4) Phillips screws securing the radio. Unplug and remove radio. (Figure G) E Continue to kit assembly. G F 2

Краткое содержание страницы № 5

99-7322 KIT ASSEMBLY DIN RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the cage and secure. (Figure B) Continue to final assembly. B 3

Краткое содержание страницы № 6

99-7322 KIT ASSEMBLY ISO DIN RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the after- market radio using the screws sup- plied with the radio. (Figure A) 2 Slide the radio into the radio opening until the side clips snap into place. (Figure B) 3 Snap the trim plate into the Radio Housing. (Figure B) Continue to final assembly. B 4

Краткое содержание страницы № 7

99-7322 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D Locate the factory wiring harness in the dash. Metra recommends using the 1 proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disasse

Краткое содержание страницы № 8

99-7322 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 04/27/10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST99-7322