Краткое содержание страницы № 1
* Shown with optional peripherals
Touchmonitor User Guide
1529L 15” LCD Desktop Touchmonitor, 3000 series
(Optional Magnetic Stripe Reader, Barcode Scanner,
Customer Display and Biometric available)
Краткое содержание страницы № 2
Elo TouchSystems 15” LCD Touchmonitor Optional Magnetic Stripe Reader, Customer Display, Barcode Scanner User Guide Revision G P/N 008603E Elo TouchSystems 1-800-ELOTOUCH www.elotouch.com
Краткое содержание страницы № 3
Copyright © 2009 Tyco Electronics. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Tyco Electronics. Disclaimer The information in this document is subject to change without notice. Tyco Elec- tronics makes n
Краткое содержание страницы № 4
T T T T Ta a a a ab b b b ble of le of le of le of le of Contents Contents Contents Contents Contents Chapter 1 Auto Adjust ................................................. 33 Introduction 1 OSD Left/Right ............................................. 33 Product Description ................................................. 1 OSD Up/Down ............................................. 33 Detailed LCD Display Performance Clock ........................................................... 33 Requireme
Краткое содержание страницы № 5
C H A P T E R 1 INTRODUCTION Product Description The 1529L is a retail terminal designed to present information to the operator and the customer. The 1529L is available in serial and USB versions or combo touch monitor. The 1529L consists of a 15.0” LCD main display with a touchscreen and the following optional peripherals: customer display, vacuum fluorescent display (VFD) Customer Display, fingerprint reader, barcode scanner, credit card reader, and a 6 port USB (USB version only) Hub. T
Краткое содержание страницы № 6
The credit card reader reads all three stripes on a standard credit card or drivers license. The credit card is read by sliding the credit card, stripe side toward the display through the credit card reader forward or backward. There is a USB credit card reader only. The Hub provides 4 internal USB ports to be used by the credit card reader, the finger- print reader or barcode scanner, the touchscreen, and the customer display. The hub also supplies two USB ports to the outside of the back of th
Краткое содержание страницы № 7
Customer Display The Customer Display is a twenty character two line vacuum fluorescent display (VFD). It consists of a VFD and VFD controller. Serial Version Optional Parameters Characters per row 20 Number of rows 2 Character 5x7 dot matrix configuration Character Height 9.5mm Character width 6.2mm Character ASCII configuration Character color Blue green MTBF 300,000 hours Fingerprint Reader There is a fingerprint reader in the USB version only. General Description-FDU01B is a PC peripheral FR
Краткое содержание страницы № 8
Specifications Sensor SecuGen FOR Image Capture Speed 600ms/frame Image Transfer Speed 500Byte/ms Pixel Resolution 356x292 USB Signaling Type Full Speed Type Theory of Operation The USB host initiates communication with the FDU01 using operation commands (Sensor LED On, Fingerprint Capture Start and Stop). Fingerprint data are then cap- tured by the CMOS sensor at a total image size of 356 x 292 with 8-bit gray level. The image frame transfer speed is 500 bytes/ms. It takes about 600 millisecond
Краткое содержание страницы № 9
5. Effective form factor; ability to be mounted on side of ET1529L 6. USB interface that complies with USB 2.0 standards 7. USB bus powered 8. Easy communication between host and scanner 9. Visible laser diode operating at 650nm 10.600+ scans/sec 1-D scanner: 1. Ability to read 1-D codes 2. Scan angle Minimum: 47º ± 3º 3. Low cost solution 4. Effective form factor; ability to be mounted on side of ET1529L 5. USB interface that complies with USB 2.0 standards 6. USB bus powered 7. Easy communica
Краткое содержание страницы № 10
C H A P T E R 2 INSTALLATION AND SETUP This chapter discusses how to install your LCD touchmonitor and how to install Elo TouchSystems driver software. Unpacking Your Touchmonitor Check that the following items are present and in good condition: Touchmonitor USB Cable Video cable Power cable US/Candian European power cable DVI cable Speaker CD and Quick Install Guide 2-6
Краткое содержание страницы № 11
Product Overview Main Unit Note: Shown with optional Biometric & MSR. Rear View Note: Shown with optional Rear Facing Customer Display. 2-7
Краткое содержание страницы № 12
Side View Base Bottom View or 2-8
Краткое содержание страницы № 13
TM Kensington Lock TM The Kensington lock is a security device that prevents theft. To find out more about this security device, do to http://www. kensington.com. 2-9
Краткое содержание страницы № 14
USB Interface Connection Your touchmonitor comes with only one touchscreen connector cables: USB cable. (For Windows 2000, Me and XP systems only.) To set up the display, please refer to the following figures and procedures: Remove the Cable Cover The cables are connected at the back of the monitor. cable cover To remove the cover, grasp the lip of the cover and pull towards you until it snaps off. 2-10
Краткое содержание страницы № 15
CAUTION Before connecting the cables to your touchmonitor and PC, be sure that the computer and touchmonitor are turned off. NOTE Before connecting the cables to the touchmonitor, route all the cables through the hole in the second as shown in the picture above. 2-11
Краткое содержание страницы № 16
The following illustrations guide you step by step in connecting your touchmonitor using a USB cable connection. Power cord Connect one end of the power cord to the monitor and the other end to wall. Connect the power cable to the power port in the monitor. 2-12
Краткое содержание страницы № 17
Video cable Connect one end of the video cable to the rear side of computer and the other to the LCD. Tighten by turning the two thumb screws clockwise to ensure proper grounding. You can select DVI video cable or D-SUB15 video cable. DVI cable 2-13
Краткое содержание страницы № 18
Speaker cable Connect one end of the speaker cable to the speaker port in the computer and the other end to the port in the monitor. 2-14
Краткое содержание страницы № 19
USB cable Connect one end of the USB cable to the rear side of the computer and the other to the LCD monitor. The USB cable is for optional touch, MSR, CD and Finger Print Reader. Only one USB cable is needed because the device contains a self powered USB 1.1 Hub. Two self powered ports are available for running other USB devices. For touch only, no USB Hub is present. 2-15
Краткое содержание страницы № 20
USB / SERIAL Interface Connection Your touchmonitor comes with only one touchscreen connector cables: USB cable. (For Windows 2000, Me and XP systems only.) To set up the display, please refer to the following figures and procedures: Remove the Cable Cover The cables are connected at the back of the monitor. cable cover To remove the cover, grasp the lip of the cover and pull towards you until it snaps off. 2-16
