Краткое содержание страницы № 1
High End Residential
In-Ground Basketball System
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
Adult Assembly Required.
This manual, accompanied by sales receipt, should be saved and kept on hand as a convenient reference, as it contains
important information about your model.
Write Model Number
WARNING!
From Box Here:
READ AND UNDERSTAND OPERATOR'S
MANUAL BEFORE USING THIS UNIT.
FAILURE TO FOLLOW OPERATING
INSTRUCTIONS COULD RESULT IN
INJU
Краткое содержание страницы № 2
SAFETY INSTRUCTIONS WARNING FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN Read and understand warnings listed SERIOUS INJURY, PROPERTY DAMAGE AND WILL VOID WARRANTY. below before using this product. Owner must ensure that all players know and Failure to follow these warnings may follow these rules for safe operation of the system. result in serious injury and/or property damage. To ensure safety, do not attempt to assemble this system without following the instructions carefully.
Краткое содержание страницы № 3
PARTS LIST Item Qty. Part No. Description 1 1 968880 Pole 2 1 908266 Tube, 8x8, Ground Anchor, Black 3 1 Rim Assembly 4 1 Net 5 4 203017 Nut, Hex, 3/8-16 6 4 203300 Washer, 3/8 Locking, .380 I.D., .63 O.D. 7 4 200512 Bolt, Hex, 3/8-16 x 3.5” Long 8 1 204922 Pin, Hitch 9 1 204923 Pin, Cotter, #8 10 3 204993 Rebar, .5” diameter, 18” Long ID# 516000 06/05 11 1 516000 Label, Height Adjustment 12 1 204940 Screw Jack 11 13 1 Backboard 14 1 80854501 Rod, Threaded Assembly, 5/8-11 x 19.8”, Zinc 15 4
Краткое содержание страницы № 4
HARDWARE IDENTIFIER (BOLTS & SCREWS) Item #23 (1)* Item #20 (1) Item #7 (4) Item #29 (4) Item #34 (4) HARDWARE IDENTIFIER (NUTS, WASHERS & SPACERS) Item #28 (3) Item #6 (4) Item #33 (2)* Item #15 (4)* Item #21 (16) Item #24 (9) Item #5 (4) Item #22 (9)* Item #26 (1) Item #25 (8) HARDWARE IDENTIFIER (OTHER—NOT ACTUAL SIZE) Item #9 (1) Item #27 (1) Item #19 (26) Item #8 (1) ID# M88724C1 08/06 4
Краткое содержание страницы № 5
Ensure ground is level with playing surface, then dig pole hole. 1. 24" (61 cm) 48" (121.9 cm) WARNING! 24" (61 cm) GROUND SURFACE PLAYING SURFACE 48" (121.9 cm) CONTACT UTILITIES BEFORE DIGGING. Install nuts (25) onto the ground tube bolts as shown. 2. NOTE: 25 Nuts on the top of the plate are used for leveling the pole after system is fully assembled. 2 08/06 ID# M88724C1 5
Краткое содержание страницы № 6
Fill hole with concrete. Tamp down concrete to release air pockets 3. and build drainage hill. DRAINAGE HILL 1" (2.54 cm) PLAYING SURFACE SIDE VIEW 4. Insert rebar (10) through holes in ground tube assembly (2) as shown. 2 10 10 10 ID# M88724C1 08/06 6
Краткое содержание страницы № 7
Insert ground tube assembly (2) into cement as shown. Move assembly around to release any air 5. pockets in cement, then rest mounting plate on cement drainage hill. Apply some pressure to level mounting plate on top of drainage hill. Level mounting plate and square with playing surface. Clean off any excess cement on mounting plate at this time and place washers (24) on mounting bolts (19). 2 10 IMPORTANT! NOTE ORIENTATION 10 Front of mounting plate (2) must be parallel with playing 10 surf
Краткое содержание страницы № 8
Insert bushings (19) into areas 6. shown. 13 19 19 19 19 19 19 19 19 19 19 19 19 19 1 17 19 19 19 19 18 19 19 19 ID# M88724C1 08/06 8
Краткое содержание страницы № 9
Rest top of pole (1) on a piece of scrap wood (not included) and line up holes in pole to holes in 7A. mounting plate (2) as shown. 1 WARNING! PLAYING SURFACE THREE CAPABLE ADULTS SCRAP WOOD REQUIRED FOR THIS (NOT INCLUDED) PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY 1 DAMAGE. 2 PLAYING SURFACE Insert bolt (28) through holes in plate and pole and secure with nut (22). 7B. 1 28 22 08/06 ID# M88724C1 9
Краткое содержание страницы № 10
8. WARNING! TWO people are required to lift pole into position so that the threaded assembly rod (14) can be installed and secured by the THIRD person. THREE CAPABLE ADULTS While pole is being supported by TWO REQUIRED FOR THIS capable adults, position rod (14) and lock PROCEDURE. FAILURE TO FOLLOW THIS into place with hitch pin (8) and cotter WARNING COULD RESULT pin (9). IN SERIOUS INJURY AND/OR PROPERTY Slide barrel washer (27) onto other end of DAMAGE. rod (14) and secure with washer (24)
Краткое содержание страницы № 11
While still in forward position, attach both upper 9. and lower yokes (17 & 18) to pole as shown. WARNING! THREE CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 22 21 17 18 21 28 08/06 ID# M88724C1 11
Краткое содержание страницы № 12
Attach elevator adjustment (12) to 10. lower yoke (18). WARNING! THREE CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 22 18 21 19 12 19 21 20 ID# M88724C1 08/06 12
Краткое содержание страницы № 13
Attach elevator adjustment (12) to pole bracket. 11. WARNING! THREE CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 21 21 23 22 33 33 12 08/06 ID# M88724C1 13
Краткое содержание страницы № 14
Attach backboard (13) to upper and lower 12. yokes (18 & 17). First attach board (13) to upper yoke (17), Then, hinge board to match up with holes in A. B. using TWO people to hold the board and lower yoke (18), FIG. C, and secure with ONE person to attach hardware (FIG. A). hardware as shown in FIG. D. Use hardware as shown in FIG. B. WARNING! THREE CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. FIG. C FIG. A F
Краткое содержание страницы № 15
Before starting rim assembly, tighten nut (26) until it is positioned 6-3/4” from the end of the rod (14) as 13. shown (Figure A). Remove rim cover (16), attach rim assembly (3) to backboard (13) and reattach rim cover (16). ** For rim assembly, see instructions included with rim. IMPORTANT! Carefully cut and peel protective film away from 14 board prior to attaching rim. 26 FIGURE A. 5 6 6 13 Rim Assembly 16 3 15 15 Refer To Instructions Included With Rim 7 Hardware For Rim 7 Assembly. 08/06 ID
Краткое содержание страницы № 16
10 9 87 14. Set-up For Left Side Set-up For Right Side Apply height indicator A. 30 30 labels (32 & 31) to height indicators (30). 10 10 9 7 9 8 7 8 31 10 10 32 7 9 8 9 8 7 Attach height indicators to lower yoke in area shown by turning B. screws (29) into place with a Phillips head screwdriver. IMPORTANT! 29 NOTE ORIENTATION OF HEIGHT INDICATORS: 10’ MARK SHOULD FACE AWAY FROM BACKBOARD. Attach height indicators C to lower yoke in area shown by turning screws (29) into place 29 with a Phillips
Краткое содержание страницы № 17
16. Upright pole (1) by tightening nut (26). WARNING! Using 15/16” wrench, turn nut (26) clockwise to begin standing pole upright. Continue to THREE CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. TWO PEOPLE ARE REQUIRED TO turn nut (26) until pole has come to rest GUIDE AND SUPPORT THE SYSTEM WHILE THE against washers (24) and pole is vertical. THIRD PERSON IS TIGHTENING NUT (26) TO RAISE THE SYSTEM UPRIGHT. Once pole is in its final position, install FAILURE TO FOLLOW THIS WARNING COULD washers
Краткое содержание страницы № 18
After pole has been secured to anchor plate (2) loosen nut (26), 17. remove cotter pin (9), and pull out pin (8). This will allow the removal of the threaded assembly rod (14) which is no longer necessary for the remainder of the assembly and installation of system. WARNING! ONLY AFTER THE ANCHOR PLATE HAS BEEN FULLY TIGHTENED: Remove cotter pin (9) and pin (8) to remove threaded assembly rod (14) from anchor plate (2). 26 24 27 14 9 8 25 ID# M88724C1 08/06 18
Краткое содержание страницы № 19
Check system leveling. Pole (1) 18. should be level in all directions. After system is leveled, completely tighten all nuts (25). NOTE: If adjustment is necessary, adjust system by rotating 1 the nuts (25) between anchor plate (2) and pole flange. 25 2 19. Apply height adjust ment label (11). Adjust system by turning crank until desired height is reached per height indicator (30). 30 WARNING! 10 feet 12 (3.05 m) 11 READ AND UNDERSTAND WARNING & HEIGHT ADJUSTMENT LABELS BEFORE USING THIS UNIT. F
Краткое содержание страницы № 20
LIMITED LIFETIME WARRANTY ® Subject to proper installation and normal use, Spalding warrants, subject to limitations below, to the original retail ® purchaser all structural components of the Spalding system to be free of defects in material and workmanship for the duration of ownership by the original retail purchaser. Merchandise must be shipped prepaid with a copy of proof of purchase to our factory for examination to see whether it needs to be repaired or replaced. Any labor costs, travel e
