Руководство по эксплуатации Clam Corp Fish Trap Voyager 8245

Краткое содержание страницы № 1

Model No.
- 8245 -
p/n 108304
Specifications
Height: 72” (23” packed)

Width: 72”

Depth: 93” (37” packed)

Weight: 135 lbs.

- Clam Customer Service Information -
NOTICE!! Once used, this shelter cannot be returned to the store. If you have a
Warranty Claim, please contact Clam Corporation Customer Service by email
inquiry or direct by calling:
Customer Service Hrs: - 8am to 4pm, Mon. - Fri. Central Standard Time

Clam Corporation, Inc.

600 Clydesdale Trail
Medina, MN 55340
P

Краткое содержание страницы № 2

- Parts List - Item Qty p/n Description 1 12 101048 Slide Block 2 6 101069 Canopy Pole 3 8 101080 1/4" Dia. X 1-1/4" Long Phillips Screw 4 8 101081 1/4" Flat Washer 5 40 101082 1/4" Thin Locknut 6 8 101083 Tube Cap Spacer 7 6 101088 1/4" Dia. X 3/4" Long Phillips Screw 8 1 101095 Tow Rope 9 1 101116 U-Channel Molding 10 2 101121 Porch Pole 11 1 101124 Short Roof Spreader Pole 12 1 101130 Long Roof Spreader Pole 13 6 101146 1-1/2" X 1-3/4" Aluminum Angle X 9" Long 14 12 101147 #10

Краткое содержание страницы № 3

- Assembly Diagram - 3

Краткое содержание страницы № 4

- Step One - 4

Краткое содержание страницы № 5

- Step Two - 5

Краткое содержание страницы № 6

- Step Three - 6

Краткое содержание страницы № 7

- Step Four - 7

Краткое содержание страницы № 8

- Step Five - 8

Краткое содержание страницы № 9

- Step Six - 9

Краткое содержание страницы № 10

- Step Seven - Slide the Canopy Hoop Poles onto the Canopy Poles until the spring buttons engage the holes near the ends of each Canopy Hoop Pole. Support the first Canopy Hoop Pole as pictured with the Rear Adjustable Spreader Poles (the shorter of the two provided lengths). Lean the two remaining Canopy Hoop Poles against the first. 10

Краткое содержание страницы № 11

- Step Eight - Drape the Tent over the supported hoops then go inside and spread out the Canopy Hoop Poles, attaching the Roof Velcro as you go. Orient the Porch Hoop Pole so that the holes face upward and then feed the length of the pole through the three Porch Hoop Sleeves sewn on the Tent. Slide the Porch Hoop Pole onto the Porch Poles, engaging the third hole position. Attach the Porch Hoop Velcro on each side of the Tent. Remove the Rear Adjustable Spreader Poles now supporting the

Краткое содержание страницы № 12

- Step Nine - To “set” the Tent, grasp the Tent Material at the rear of the shelter and pull it downward. Observe the porch area of the tent lifting accordingly as you pull. When the U-Channel Molding is correctly installed, the Porch Hoop Pole will lightly touch the floor. To achieve this condition, start by finding the center of the Molding. From behind the unit, pull the midpoint of the Tent downward and fold the Tent Material under the Base Lip. Press the midpoint of the Molding over

Краткое содержание страницы № 13

- Step Ten - Angle the Seat Assembly slightly while placing the bottom lip of the Front Seat Bracket under the outside edge of the Base lip. Tilt the complete assembly downward so that the Rear Seat Bracket lands upon the Support Tube. Reach under the Rear Seat Bracket and slide the Latch Clip outwards and then up against the underside of the Support Tube. Squeeze the Latch Clip into the horizontal slot of the Rear Seat Bracket. Secure the position of the Latch Clip by pushing it into the

Краткое содержание страницы № 14

- Tips for Use - Folding and transporting your Fish Trap is easy: Unsnap the Roof Spreader Poles, Rear Spreader Poles, and Front Spreader Poles. Lay them in the bottom of the base. Push the spring buttons and retract each hoop, starting with the rear hoop and working towards the front. Rotate all retracted hoops to the resting position. Tuck the tent into the base and between the hoops so that no material is left hanging on the ground for transport. Cover with the Travel Cover* (an o