Краткое содержание страницы № 1
1822-I
Pipe and Bolt
Threading Machine
OPERATOR’S
MANUAL
• Français – 25
• Castellano – pág. 51
WARNING!
Read this Operator’s Manual
carefully before using this
tool. Failure to understand
and follow the contents of
this manual may result in
electrical shock, fire and/or
serious personal injury.
Краткое содержание страницы № 2
1822-I Pipe and Bolt Threading Machine Table of Contents Recording Form for Machine Serial Number...............................................................................................................................................1 General Safety Information Work Area Safety........................................................................................................................................................................................2 Electrical Safety ...........
Краткое содержание страницы № 3
1822-I Pipe and Bolt Threading Machine 1822-I Pipe and Bolt Threading Machine Record Serial Number below and retain product serial number which is located on nameplate. Serial No.
Краткое содержание страницы № 4
1822-I Pipe and Bolt Threading Machine • Do not abuse cord. Never use the cord to pull the General Safety Information plug from an outlet. Keep cord away from heat, oil, WARNING! Read and understand all instructions. Failure sharp edges or moving parts. Replace damaged to follow all instructions listed below may re- cords immediately. Damaged cords increase the risk of sult in electric shock, fire and/or serious per- electrical shock. sonal injury. SAVE THESE INSTRUCTIONS! • When operating a too
Краткое содержание страницы № 5
1822-I Pipe and Bolt Threading Machine ables better control of the tool in unexpected situa- Call the Ridge Tool Company, Technical Service De- tions. partment at (800) 519-3456 if you have any questions. • Use safety equipment. Always wear eye protec- WARNING Foot Switch Safety tion. Dust mask, non-skid safety shoes, hard hat, or Using a threading machine without a foot switch increases hearing protection must be used for appropriate con- the risk of serious injury. A foot switch provides bette
Краткое содержание страницы № 6
1822-I Pipe and Bolt Threading Machine Pump.............................Gerotor-Type Noise Level....................81 DBA Cutter.............................No. 364 – Roll-Type Cut-Off, 1 Pipe – /8″ through 2″ 1 Bolt – /4″ through 1″ Reamer..........................No. 344 5-Flute Cone, Figure 1 – Locked Foot Switch 1 Right Hand, /8″ through 2″ Weight ...........................210 Lbs. (95 kgs.) Description, Specifications and Standard Equipment Standard Equipment: • Model No. 1822-I Threadin
Краткое содержание страницы № 7
1822-I Pipe and Bolt Threading Machine Die Heads and Dies Pipe Bolt Model Capacity Capacity Dies Opening Operation 1 1 811A NPT /8″ - 2″ /4″ - 2″ Universal Quick R.H. 1 1 815A NPT /8″ - 2″ /4″ - 2″ Universal Self R.H. 1 842 NPT /4″ - 2″ — Universal Quick L.H. 1 3 816 NPT /8″ - /4″ — Universal TAP R.H. 1 817 NPT 1″ - 2″ /4″ - 2″ Universal TAP R.H. 1 1 811A BSPT /8″ - 2″ /4″ - 2″ Universal Quick R.H. 1 1 815A BSPT /8″ - 2″ /4″ - 2″ Universal Self R.H. 1 531 Bolt — /4″ - 1″ 500B Quick R.H./L.H. 1 5
Краткое содержание страницы № 8
1822-I Pipe and Bolt Threading Machine Figure 2 – Machine Dimensions 3 shown in the detail drawing. Use the four (4) /8″ - 16 bracket is held in place by the axle shaft. Slide a 1 x 2 /2″ hex bolts to secure the legs to the cross-mem- wheel onto the axle. Slide a flat washer over the axle ber. Adjust the two halves of the stand stop to the and install a cotter pin to hold the wheels on the axle. proper distance to fit into the rear legs on the stand. 5. Mount machine to the stand using four (4)
Краткое содержание страницы № 9
1822-I Pipe and Bolt Threading Machine Rear Latch Push Mounting Machine to No. 1406 Folding Wheel Stand 1. Raise rear handle of stand to a vertical position and tighten mounting bolts. 2. Using hand crank, raise stand to its operating height. Place machine on stand with carriage away from 1 wheels (Figure 4). Insert four /4″ – 20 bolts through rails into machine base. Tighten bolts. Oil Line Notch Installing No. 1460 Oil Pan Cover Oil Pan NOTE! No. 1460 Oil Pan Cover installs in machine oil Cove
Краткое содержание страницы № 10
1822-I Pipe and Bolt Threading Machine CAUTION DO NOT use a sling through the spindle tube RIDGID Center-Lock Chuck only. Rear Centering/Front Gripping No. 364 Cutter Front Cover No. 344 Reamer Rear Cover Top Cover Self-Opening Die Head Control Chip Pan Switch Transmission Lever Drain Plug Handwheel Figure 6 – Sling Transportation Machine Inspection Foot Switch WARNING Figure 7 – 1822-I Threading Machine 6. Inspect the Threading Machine for any broken, miss- ing, misaligned or binding parts as
Краткое содержание страницы № 11
1822-I Pipe and Bolt Threading Machine NOTE! High speed dies are recommended for use with prevents others from accidentally contacting the ma- this machine when threading 1″ - 2″ pipe at 45 chine or workpiece and either causing the equipment RPM. Because of its high speed, alloy dies will to tip or becoming entangled in the rotating parts. wear quickly and produce poor quality threads. 5. If mounted on a 1406 Folding Wheel Stand, make 11. Clean metal shavings and other debris from the chip sure
Краткое содержание страницы № 12
1822-I Pipe and Bolt Threading Machine • Depress and hold the foot switch. Inspect the mov- WARNING To avoid equipment tip-overs, position the pipe supports under the workpiece. ing parts for misalignment, binding, odd noises or any other unusual conditions that may affect the 6. Place the control switch in the CLOSE position and safe and normal operation of the machine. If such step on machine’s foot switch. The machine will au- conditions are present, have the machine serviced. tomatically cen
Краткое содержание страницы № 13
1822-I Pipe and Bolt Threading Machine 7. Tighten the feedscrew handle slowly and continu- Speed Selection Chart ously until the pipe is cut. Do not force the cutter Size/Material Recommended RPM 1 into the workpiece. /8″ – 2″ Pipe 45 1 /4″ – 1″ Bolt 45 8. Release the foot switch and remove your foot from the High Torque Applications 16 housing. • Stainless Steel • Bolt Above 1″ 9. Swing pipe cutter back to the UP position. Low Voltage Conditions 16 NOTE! 20 amp circuits with good line voltage a
Краткое содержание страницы № 14
1822-I Pipe and Bolt Threading Machine 8. Move die head to UP position. 9. With head in vertical position, rotate cam plate until roll pin on lock screw can be positioned in slot under size 9. Release foot switch and remove your foot from the bar. In this position dies will lock in die head. Make housing. sure roll pin points toward end of size bar marked RE- MOVE DIES. Removing Pipe From The Threading Machine 10. Adjust die head size bar until index line on lock screw is aligned with proper siz
Краткое содержание страницы № 15
1822-I Pipe and Bolt Threading Machine NOTE! High speed dies are recommended for thread- (Figure 13 – Model 816/817 Die Head) against the ing 1″ to 2″ pipe at 45 RPM. plunger knob (as shown). 1. Lay die head on bench with numbers face up. 2. Lay the die head down flat on a table or bench with the numbers facing up. 2. Flip throwout lever to OPEN position. 3. Pull up on the plunger knob and rotate the handle 3. Loosen clamp lever approximately three turns. counter-clockwise all the way (to the le
Краткое содержание страницы № 16
1822-I Pipe and Bolt Threading Machine Nipple Threading Procedure Die Die 1. Ream, thread and cut pipe to desired length using Die Flush W W With End standard procedures. of Pipe Pipe 2. Install No. 819 and 839 adapter (Figure 16). Pipe 1 3. Position insert with small end toward adapter for /8″ to Starting to Cut Thread Completed Thread 3 /4″ pipe, large end toward adapter for 1″ pipe and no A - Full Width Die Thread 1 insert for pipe 1 /4″ and up. Thin Ring Gage 4. Install proper adapter and ti
Краткое содержание страницы № 17
1822-I Pipe and Bolt Threading Machine Operation Instructions Guide Post Using Geared Threaders Head Reference Lines (3) WARNING Drive Shaft Do not wear gloves or loose clothing when oper- ating Threading Machine. Keep sleeves and jack- ets buttoned. Do not reach across the machine or geared threader. Do not use this Threading Machine if the foot switch is broken or missing. Always wear eye protection to protect eyes from dirt and other for- eign objects. To prevent tipping, proper set-up of th
Краткое содержание страницы № 18
1822-I Pipe and Bolt Threading Machine 1 3. For straight threads, insert guide post with straight slot Threading 2 /2″ to 4″ Pipe (45 RPM) inward through die head to the gear case. 1. Adjust No. 141 Geared Threader and install on 1822-I Threading Machine. 4. With guide block in diagonal/straight slot, replace set screw. 2. Support pipe with a pipe stand. 3. Insert pipe into the throat of dies and tighten work- Changing Dies holder and clamp screw. (Figure 19) 4. Direct oil spout at dies and plac
Краткое содержание страницы № 19
1822-I Pipe and Bolt Threading Machine Guide Post Oil Spout Pipe Connecting Link Oil Manifold/Lever (Hidden) Workholder VJ-99 Pipe Stand Clamp Screw Carriage Drive Shaft Saddle (Set Screws) Pinion Sleeve Handwheel Figure 20 – Operation of the No. 141 Geared Threader No. 821 Blade Cutter and Left Hand Machine Operation No. 822 Adapter Kit Machine is capable of left hand operation. However, user or Authorized Service Center modification is re- No. 821 Blade Cutter allows the machine to groove, qu
Краткое содержание страницы № 20
1822-I Pipe and Bolt Threading Machine Positioning Rear Centering Jaws for Left Hand Operation (Figure 21) 1. Rear centering jaws will be pointing outward after front jaw reversal to left hand operation. 2. Remove three E-Clips holding the rear retainer in place and remove retainer. 3. Remove spacers and rear jaws. 4. Reverse rear jaws and reinstall on square pin or rods. 5. Reinstall spacers, rear retainer and retaining clips. NOTE! Before reinstalling machine covers make sure both front and re
