Руководство по эксплуатации Harbor Freight Tools PACIFIC HYDROSTAR 1/3 HP Submersible Sump Pump with Vertical Float Switch 68476

Краткое содержание страницы № 1

1/3 HP Submersible Sump Pump
with Vertical Float Switch
Item 68476 Specifications
Float Switch Operation Height 7.1 IN. ON / 2.8 IN. OFF
Electrical Requirements 120V~ / 60Hz / 7.6A
Power Cord Length 10 FT.
Maximum Capacity 3000 GPH
Maximum Delivery Height 25 FT.
1.5 IN. NPT
Discharge Size
(includes 1.25 IN. Adaptor)
Maximum Water Temperature 77° F (25°C)
252728
Read the separate Sump Pump Safety Warnings,
Installation and Operation Instructions before
using this product.
Failure to do so ca

Краткое содержание страницы № 2

PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEM

Краткое содержание страницы № 3

Sump Pump Safety Warnings, Installation and Operation Instructions Read this material before using this product. Failure to do so can result in serious injury. SAVE THIS SUMP PUMP SAFETY WARNINGS, INSTALLATION AND OPERATION INSTRUCTIONS AND THE SPECIFICATION SHEET FOR FUTURE REFERENCE. When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call 1-800-444-3353 as soon as possible. Note: There may be some slight differences in the app

Краткое содержание страницы № 4

reproductive harm. Wash hands after handling. Before start-up, note the following: (California Health & Safety Code § 25249.5, et seq.) The pump can be connected to any shock-proof plug 14. The warnings, precautions, and instructions which has been installed according to regulations. discussed in this instruction manual cannot The plug must have a supply voltage of 120 V~ at 60 Hz. cover all possible conditions and situations that may occur. It must be understood by the CAUTION operato

Краткое содержание страницы № 5

at least 22 IN. deep WARNING! If either power cord or plug is damaged, 3. Fit a sump cover with a hole for the output pipe do not use the pump. The power cord or plug and power cords. Thread the Power Cords may only be repaired by a certified electrician. through their holes, but do not plug them in yet. Set the sump cover aside for now. Areas of use Note: The sump cover can also be fitted with a vent pipe, if desired. 1. This pump is designed to pump clear water only. 4. Attach a disch

Краткое содержание страницы № 6

10. After connecting power to the pump and Operation periodically afterwards, test the pump: a. Fill the basin to above the Float Switch Operation After reading these instructions, ON Height. The pump should start pumping. consider the following points before starting the pump: b. The pump should pump the water down to below its Float Switch Operation OFF 1. Verify that the pump rests on the floor of the shaft, Height and then stop pumping. if it is not suspended by the handle. c. If the

Краткое содержание страницы № 7

Cold Weather Storage Maintenance In cold weather, when the Pump is not in use, protect the interior of the Pump from freezing by draining the water and pumping a permanent type automobile anti-freeze containing a rust inhibitor TO PREVENT SERIOUS INJURY FROM through the system. A 50% mixture with water is ACCIDENTAL OPERATION: recommended. Be sure to flush the system with a Unplug the Pump from its electrical outlet and neutralizing liquid prior to re-use of the Pump. ALLOW TO COOL FO

Краткое содержание страницы № 8

Troubleshooting Problem Possible Causes Possible Solutions Pump runs, but Disconnect power cords immediately Disconnect power cords immediately will not deliver to prevent damage from running dry. to prevent damage from running dry. any water. 1. Pump “airlock”. 1. Drill a 3/16 IN. diameter air bleed hole Impeller trapped in an air bubble. through the Discharge Pipe just above the Lower Base. 2. Shut off valve closed (if installed). 2. Open valve. 3. Filter clogged. 3. Clean out dirt and deb

Краткое содержание страницы № 9

To take advantage of this warranty, the product or part LIMITED 90 DAY WARRANTY must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If Harbor Freight Tools Co. makes every effort to assure our inspection verifies the defect, we will either repair that its products meet high quality and durability or replace the product at our election or we may elect standards, and warrants to the original