Краткое содержание страницы № 1
Security Label Applier
Operator Manual
Model
SLA-1, SLA-2 ML-44180
SLA-2A ML-44197
SLA-3 ML-44192
701 S. RIDGE AVENUE
TROY, OHIO 45374
937 332-3000
www.hobartcorp.com
© HOBART 2006 F33995 (Rev. A, 6/06)
Краткое содержание страницы № 2
Security Label Applier (SLA) SAVE THESE INSTRUCTIONS Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
Краткое содержание страницы № 3
The Security Label Applier (SLA) is designed to apply an Electronic Article Surveillance (EAS) label to a standard Ultima Security Label Applier scale label. The SLA works in conjunction with an Ultima (with remote keypad) and an Ultima Wrapping System (UWS), Compact Label Applier (CLA) or Indexing Label Applier (ILA). As a label is printed and expelled from the Ultima Printer, the SLA attaches a security label to the adhesive side of the merchandising label. The UWS, CLA or ILA then
Краткое содержание страницы № 4
Note If used with an HWS or NSW Semi Automatic System, the security label is automatically placed on the Ultima scale label. The Operator then hand applies the labels to the package. There are two types of security labels available. Depending on your store security system, you will either use the Checkpoint label (similar in size to the safe handling label) or the Sensormatic label (similar to what is used with audio CDs). Note For label ordering information, contact you
Краткое содержание страницы № 5
1. At the Ultima Keypad, PRESS [SUPER MENU ON/OFF]. If applicable, enter your Secret ID. The Supervisor Menu displays. 2. PRESS [F5] to select Scale Setup Menu. 3. PRESS [F3] to select Labels Menu. 4. PRESS [F6] to select Security Labels. © HOBART 2006 Page 5 of 12 F33995 (Rev. A, 6/06)
Краткое содержание страницы № 6
5. From the Security Labels screen, enter the minimum Unit Price and/or the minimum Total Price. A security label will be applied to any package with a Unit Price and/or Total Price that is the same as or higher than the amounts entered. If the Unit Price and Total Price are lower than the entered prices, the security label will not be applied. 6. PRESS [ESC] to return to the Start a Run screen. To set up the SLA to apply a label by PLU: 1. At the Ultima Keypad, PRESS [SUP
Краткое содержание страницы № 7
3. Use the numeric keypad to enter PLU number in the Product number and PRESS [ENTER]. 4. PRESS [F2] to select Apply Security Label. 5. PRESS [ESC] to return to the Start a Run screen. Once set up, the SLA runs with minimal operator intervention. The labels are automatically generated, combined and placed Operating the SLA on the appropriate package. The SLA contains a label sensor to alert the operator when out of labels or when labels are not advancing. When the
Краткое содержание страницы № 8
The SLA contains a label sensor to alert the operator when out of labels or when labels are not advancing. When applicable, Loading Labels the message Out of Security Labels displays on the Ultima console and a beep sounds to alert the operator. Although, when out of security labels, the Ultima merchandising labels continue to print. You may also receive this message if the SLA is turned off, but you are still operating the Ultima printer. Refer to the following procedures and diagrams
Краткое содержание страницы № 9
Fig 1 Fig 2 Fig 3 Fig 4 © HOBART 2006 Page 9 of 12 F33995 (Rev. A, 6/06)
Краткое содержание страницы № 10
Maintain the SLA by regularly cleaning the paper dust from inside the unit. Clean the SLA exterior surfaces with a cloth and Cleaning and warm water/detergent solution. When cleaning, be sure to Maintaining protect the unit from direct water entry. To clean the SLA: 1. Dampen a soft cloth with mild detergent and water. 2. Wipe the exterior surfaces. Note Remove any adhered labels with an alcohol soaked cloth. Do not use metal to scrape the labels or adhesive off of the unit.
Краткое содержание страницы № 11
SYMPTOMS POSSIBLE CAUSES/REMIDIES Multiple labels are issued followed by an 1. Verify labels threaded correctly. audible beeping sound. 2. Call local Hobart office. No label is issued followed by an audible 1. Out of security labels. beeping sound. 2. Missing security labels on backing paper. 3. Verify labels threaded correctly. 4. Call local Hobart Office. Security label placement on Ultima label is 1. Verify that dwell control lever is resting incorrect. against the ba
Краткое содержание страницы № 12
© HOBART 2006 F33995 (Rev. A, 6/06)
