Краткое содержание страницы № 1
Demolition Hammer
MODEL HM0810B
002874
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
www.makitatools.com
Краткое содержание страницы № 2
SPECIFICATIONS Model HM0810B Blows per minute 2,900 Overall length 433 mm (17-1/32”) Net weight 5.3 kg (11.7 lbs) • Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area 4. Double insul
Краткое содержание страницы № 3
6. Do not expose power tools to rain or wet Tool Use and Care conditions. Water entering a power tool will 15. Use clamps or other practical way to increase the risk of electric shock. secure and support the workpiece to a 7. Do not abuse the cord. Never use the cord stable platform. Holding the work by hand or to carry the tools or pull the plug from an against your body is unstable and may lead outlet. Keep cord away from heat, oil, to loss of control. sharp edges or moving parts. Replace 16.
Краткое содержание страницы № 4
24. When servicing a tool, use only identical Use of unauthorized parts or failure to follow replacement parts. Follow instructions in Maintenance instructions may create a risk of the Maintenance section of this manual. electric shock or injury. USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in l
Краткое содержание страницы № 5
tion. Without proper warm-up, hammering 11. Do not point the tool at any one in the area operation is difficult. when operating. The bit could fly out and injure someone seriously. 7. Always be sure you have a firm footing. Be sure no one is below when using the 12. Do not touch the bit or parts close to the tool in high locations. bit immediately after operation; they may be extremely hot and could burn your 8. Hold the tool firmly with both hands. skin. 9. Keep hands away from moving parts. 13
Краткое содержание страницы № 6
FUNCTIONAL CAUTION: DESCRIPTION Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 002887 Switch action 1 2 CAUTION: Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released. Switch can be locked in “ON” position for ease of operator comfort during extended use. Apply caution 1. Lock button when locking tool in “ON” position and maintain firm 2. Swit
Краткое содержание страницы № 7
002914 Installing or removing the bit Clean the bit shank before installing the bit. 1 Press in the tool retainer and turn it until the red dots on the 2 tool retainer and the tool holder are aligned. Release the tool retainer. 1. Red dot (Tool holder) 2. Red dot (Tool retainer) 002915 Insert the bit into the tool holder as far as it will go. Press in the tool retainer and turn it a full 180 degrees. Then release it to secure the bit. 1 To remove the bit, follow the installation procedure in rev
Краткое содержание страницы № 8
002949 Use a hex wrench to remove the rear cover. 1 2 1. Hex wrench 2. Rear cover 002950 Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure 1 the brush holder caps. 2 1. Screwdriver 2. Brush holder cap 002963 Lubrication 1 This tool requires no hourly or daily lubrication because it 2 has a grease-packed lubrication system. It should be relubri- cated after every 6 months of operation. Send the complete tool to Makita Authorized or
Краткое содержание страницы № 9
CAUTION: Do not tighten the crank cap excessively. It is made of resin and is subject to breakage. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of in
Краткое содержание страницы № 10
Memo 10
Краткое содержание страницы № 11
Memo 11
Краткое содержание страницы № 12
Memo 12
Краткое содержание страницы № 13
First-Class Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold 13 Cut
Краткое содержание страницы № 14
MAIL THIS PORTION Your answers to the following questions are appreciated. 1. This product was purchased from: 3. How did you learn about this product: Home Center Other ( ) Magazine Radio Hardware/Lumber Store From Dealer Exhibition Tool Distributor Newspaper From Friend Industrial Supply Store Display Previous Usage Construction Supply Catalog Other ( ) 2. Use of the product is intended for: 4. Most favored points are: Construction Trade Design Repair Se
Краткое содержание страницы № 15
FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ALABAMA COLORADO KENTUCKY NEW MEXICO PUERTO RICO 2365 Pelham Parkway 11839 E. 51st Ave. 1215 S. Hurstbourne Parkway 5805 Menaul Blvd. NE 200 Guayama St. Pelham, AL 35124 Denver, CO 80239-2709 Louisville, KY 40222 Albuquerque, NM 87110 Hato Rey, PR 00917 (205) 620-1791 (303) 371-2850 (502) 326-3740 (505) 881-4619 (787) 250-8776 ARIZONA CONNECTICUT LOUSIANA NEW YORK TENNESSEE 3707 E. Broadway Rd., Ste. 6 508 Spring St.
Краткое содержание страницы № 16
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement and other masonry products, and arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of
