Руководство по эксплуатации Addonics Technologies RAID RACK RR2035ASDES

Краткое содержание страницы № 1

T E C H N O L O G I E S
User Guide
RAID Rack
(RR2035ASDES)
www.addonics.com
v8.1.11
Technical Support
If you need any assistance to get your unit functioning properly, please have your
product information ready and contact Addonics Technical Support at:
Hours: 8:30 am - 6:00 pm PST
Phone: 408-453-6212
Email: http://www.addonics.com/support/query/

Краткое содержание страницы № 2

I Front Power Switch O POWER System Reset RESET Buzzer Reset Buzzer Back Punch out for USIB connectors Fans POWER TEMP LED Display FAN Punch out for USIB connectors HDD Power Supply Punch out for eSATA Punch out for port multipliers/bridges Power Switch: This is the switch to power on devices connected to the power supply. The power LED will light up to indicate power is supplied. Note: The main power switch located at the back of the enclosure must be turned on first. Reset Button: Not opera

Краткое содержание страницы № 3

Installing drives into the RAID Rack 1. Be sure the lock on each drive door is in an unlock position. If not, use the key that comes with the Disk Array to unlock the drive door. Pull on the door lever to swing open the drive door all the way. 2. Slide a 3.5” SATA hard drive into the drive slot with the drive connector side facing in. Be sure to orient the hard drive correctly as shown in the yellow label on the inside of the drive door – with drive door swing open at the bo

Краткое содержание страницы № 4

Top Cover Screws How to Remove the Top Cover: 1. Locate the 2 screws at the back of the storage rack 2. Turn screws counterclockwise to loosen. 3. Lift the top cover and pull towards the rear end of the rack. To Mount Back the Top Cover: 1. Align the top cover with the edges of the rack. 2. Lay it flat on the rack and slide it towards the front of the rack. 3. Turn screws clockwise to tighten. Thermal Management Card on the RAID Rack* Fan Connectors Overheat Buzzer Floppy Power

Краткое содержание страницы № 5

HPM-XA Port Multiplier RAID Setting Button Dip Switch SATA Host Port (Port 5) SATA Port 2 SATA Port 1 SATA Port 0 Floppy Power Connector SATA Port 3 SATA Port 4 Drive activity LED Jumper Block (J1) Error LED Jumper Block (J3) Dip Switch Settings Raid Mode 1 2 3 4 5 Individual Drive OFF OFF OFF OFF OFF (Factory Default) 0 OFF OFF ON ON ON 1 and 10 OFF OFF ON ON OFF 3 OFF OFF ON OFF OFF 5 OFF OFF OFF ON OFF Clone OFF OFF OFF ON ON Large OFF OFF ON OFF

Краткое содержание страницы № 6

Default factory DIP Switch setting: SW1 – RAID Setting DIP Switch BZS – Error buzzer function EZ – Automatic rebuilding to spare drive (one of the drives on the raid is set as a spare). If EZ is ENABLED anda drive failure occurs, the spare will automatically act as a drive replacement and rebuilding will automatically start. M2 – RAID mode 2 M1 – RAID mode 1 M0 – RAID mode 0 SW1 1 2 3 4 5 BZS EZ M2 M1 M0 1. Error buzzer function is ENABLED (BZS) when

Краткое содержание страницы № 7

Cable Connections e. On the DIP switch, change (M0 to M2) setting to the desired RAID mode using the diagram below. 1. Attach the SATA hard drives (up to 5) to the SATA ports on the Hardware Port Multiplier (HPM) using SATA cables. It is recommended to connect All settings on the diagram shows drives to the SATA ports 1 to 5 successively. • Error buzzer function is ENABLED • EZ function is DISABLED. 2. To provide power to the HPM, connect a 4-pin floppy power cable from t

Краткое содержание страницы № 8

Cable Connections e. On the DIP switch, change (M0 to M2) setting to the desired RAID mode using the diagram below. 1. Attach the SATA hard drives (up to 5) to the SATA ports on the Hardware Port Multiplier (HPM) using SATA cables. It is recommended to connect All settings on the diagram shows drives to the SATA ports 1 to 5 successively. • Error buzzer function is ENABLED • EZ function is DISABLED. 2. To provide power to the HPM, connect a 4-pin floppy power cable from t

Краткое содержание страницы № 9

RAID Setting Notes: When 2 drives are RAID 1& RAID 10 Mode connected to the HPM-XA, and DIP switch is set to this setting, the 2 drives will be SW1 1 2 3 4 5 configured as a 2-drive RAID1 array. BZS EZ M2 M1 M0 When 4 drives are connected to the HPM-XA, the 4 drives will be configured as a 4-drive RAID10 array. Clone’s action is similar to Clone Mode RAID1. However, all of the hard drives will be mirrored. Clone mode is useful SW1 especially when users like

Краткое содержание страницы № 10

Cable Connections 1. Attach the SATA hard drives (up to 5) to the SATA ports on the Hardware Port Multiplier (HPM) using SATA cables. It is recommended to connect drives to the SATA ports 1 to 5 successively. 2. To provide power to the HPM, connect a 4-pin floppy power cable from the system power supply to the floppy power connector on the HPM. 3. Optional: Connect LEDs to the Activity & Error LED jumper block Setting or Modifying the RAID Mode Using the JMicron HW RAID Manager Util

Краткое содержание страницы № 11

Cable Connections 1. Attach the SATA hard drives (up to 5) to the SATA ports on the Hardware Port Multiplier (HPM) using SATA cables. It is recommended to connect drives to the SATA ports 1 to 5 successively. 2. To provide power to the HPM, connect a 4-pin floppy power cable from the system power supply to the floppy power connector on the HPM. 3. Optional: Connect LEDs to the Activity & Error LED jumper block Setting or Modifying the RAID Mode Using the JMicron HW RAID Manager Util

Краткое содержание страницы № 12

CONTACT US www.addonics.com Phone: 408-573-8580 Fax: 408-573-8588 Email: http://www.addonics.com/sales/query/