Краткое содержание страницы № 1
Краткое содержание страницы № 2
PREFACE FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subjected to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. FCC WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provi
Краткое содержание страницы № 3
CE mark for Class B ITE (Following European standard EN55022/1998; EN61000- 3-2/1995; EN61000-3-3/1995, EN55024/1998, EN60950/1992+A1+A2+A3+A4+A11) Radio Frequency Interference Statement Warning: This is a Class B product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures. Canadian Doc Notice For Class B Computing Devices This digital apparatus does not exceed the Class B limits for radio noise emi
Краткое содержание страницы № 4
Important Safety Instructions Please read the following instructions carefully. This manual should be retained for future use. 1. To clean the LCD Monitor screen, first, make sure the Monitor is in the power off mode. Unplug the Monitor from its power source before cleaning it. Do not spray liquid cleaners directly onto the unit. Stand away from the LCD Monitor and spray cleaning solution onto a rag. Without applying excessive pressure, clean the screen with the slightly dampened
Краткое содержание страницы № 5
9. If you lost the power cord that we given, you must to purchase a same configuration/type of power cord (with ground-connection) Japan ：VCTF type, 3 wires or with ground-wire, T-mark approval is required. U.S. ：VW-1; 18AWG X 3C; SVT with national approval as UL and/or CSA approval/number(s) 2 Europe ：VDE/ÖVE and/or KEMA approval; H05VV-F, 3G, 0.75mm , or equivalent. Above power cord should bear with the type and manufacturer name on. iv
Краткое содержание страницы № 6
TABLE OF CONTENTS PREFACE..................................................................................................................... I TABLE OF CONTENTS............................................................................................ V CHAPTER 1 .................................................................................................................1 Unpacking 1 Identifying Components 2 Hot-Key Buttons for Quick Adjustment of Monitor Settings 2 The LCD
Краткое содержание страницы № 7
Краткое содержание страницы № 8
CHAPTER 1 The LCD Monitor Unpacking After you unpack your LCD Monitor; make sure the following items are included in the box and in good condition: • LCD Monitor • Monitor-to-PC Analog signal cable (15-pin) • Monitor-to-PC Digital signal cable (24-pin) (optional) • Stereo Jack Audio Cable (optional) • USB Cable (optional) • Power cord • Landing Strip • User’s manual • CD Manual If you find that any of these items are missing or appear damaged, contact your dealer immediately. D
Краткое содержание страницы № 9
Identifying Components Hot-Key Buttons for Quick Adjustment of Monitor Settings Figure 1-1: Hot-Key buttons 1.”Auto-adjust” short-cut button: Press button 2 to apply the monitor setting automatically. A small “AUTO ADJUST” OSD is also displayed. 2.” Adjust-volume” short-cut button: Press button 3 to allow you to adjust the audio volume directly. 3.” Contrast-adjust” short-cut button: Press button 4 to allow you to adjust the contrast of the display directly. ** To close t
Краткое содержание страницы № 10
The LCD Monitor — Rear View Figure 1-2: LCD Monitor’s Rear Ports 1. Audio Line-in (optional) 2. AC Power Jack 3. Upstream USB Port (optional) 4. Downstream USB Ports (optional) 5. Digital VGA Cable Connect (optional) 6. VGA Cable Connector 7. VESA interface: It can be mounted to VESA arm. (75mm pitch) 3
Краткое содержание страницы № 11
Adjusting the Viewing Angle The LCD Monitor’s vertical angle setting range is from -3° to 20° . Please see Figure 1-3. Figure 1-3: Angle Settings 4
Краткое содержание страницы № 12
Raising Your Monitor to an Upright Position and Adjusting Monitor Angle 5
Краткое содержание страницы № 13
6
Краткое содержание страницы № 14
Connecting AC Power, Video, Audio and USB Cable (Optional) Figure 1-4:Connecting the LCD Monitor to the PC Power Management System The LCD Monitor complies with the VESA DPMS (version 1.0p) power management proposal. The VESA DPMS proposal provides four phases of power saving modes by detecting the horizontal or vertical sync signal. When the LCD Monitor is in power saving mode or detects an incorrect timing, the Monitor screen will go blank and the power LED indicator will start
Краткое содержание страницы № 15
CHAPTER 2 The Display Controls The LCD Monitor’s Display Controls Figure 2-1: The LCD Monitor Panel 1. OSD Menu Button Press this button to pop up the OSD (On-Screen Display) menu. This button is also a Function Select button. 2. Adjustment Control Buttons These two buttons allow you to adjust the selected control functions in the OSD. 3. Function Select Buttons These two buttons allow you to select the control functions in the OSD. Press either button to scroll through the main me
Краткое содержание страницы № 16
Adjusting the Monitor’s Display OSD Main Menu (Please refer to Chapter 1 for details on functions) To access the OSD main menu, press the OSD Menu button. Use the Function Select buttons to scroll between the OSD main menu options. The option that is currently selected is highlighted. Analog mode: Each main menu and submenu item is covered below. Pressing the OSD Menu button causes the following screen to appear (an example): Figure 2-2: The OSD Main Menu The Monitor-Control Opt
Краткое содержание страницы № 17
AUTO-ADJUST : Use the Adjustment Control buttons to apply the automatic monitor settings. H-POSITION: Use the Adjustment Control buttons to move the LCD monitor’s display left or right on a horizontal plane. V- POSITION: Use the Adjustment Control buttons to move the LCD monitor’s display up or down on a vertical plane. PHASE: Use the Adjustment Control buttons to adjust the focus and clarity of the display. CLOCK: Use the Adjustment Control buttons to adjust the display
Краткое содержание страницы № 18
OSD-V- POSITION: Use the Adjustment Control buttons to change the position of the OSD on a vertical plane. OSD-TIMER : Use the Adjustment Control buttons to change the OSD display time. EXIT: Pressing the Function Enter button exits the OSD-Control submenu. Graphic-Control Option The Graphic-Control option lets you make adjustments that effect the contrast, brightness and color of the LCD monitor’s display. With the Graphic-Control icon selected, press the Function Enter
Краткое содержание страницы № 19
RESET: Pressing either of the Adjustment Control buttons resets Contrast, Brightness and Color parameters. EXIT: Pressing the Function Enter button exits the Graphic-Control submenu. Misc-Control Option The Misc-Control menu option lets you select the OSD display language, adjust the volume setting and view system information. With the Misc-Control icon selected (use the Function select buttons), press the Function Enter button to display the submenu. Use the Function Sele
Краткое содержание страницы № 20
Figure 2-3: The OSD Main Menu The Monitor-Control Option The Monitor-Control option allows you to adjust the LCD monitor’s display characteristics. With the Monitor-Control icon selected, press the Function Enter button to display the submenu. Use the Function Enter buttons to select one of the following submenu options: PORT-SELECT: Press the Adjust buttons to change input between VGA port and DVI digital port (optional). EXIT: Pressing the Function Enter button exits the
