Краткое содержание страницы № 1
Краткое содержание страницы № 2
Copyright Information FCC Regulations This equipment is designed to be connected to the telephone network or premises wiring © 2006 Copyright Hewlett-Packard This equipment has been tested and found using a compatible modular jack which is Development Company, L.P. to comply with the limits for a Class B digital Part 68 compliant. This equipment cannot be device, pursuant to Part 15 of the FCC rules. used on telephone company-provided coin Reproduction, adaptation or translation These limits are
Краткое содержание страницы № 3
Table of contents 1 Setting up the all-in-one Step 1: Prepare the location...................................................................................................................1 Step 2: Regulate the environment..........................................................................................................1 Step 3: Verify the package contents.......................................................................................................2 Step 4: Locate the all-in-on
Краткое содержание страницы № 4
vi ENWW
Краткое содержание страницы № 5
460 mm (18.1 inches) 430 mm (16.9 inches) 1 Setting up the all-in-one Step 1: Prepare the location Place the all-in-one on a sturdy, level surface in a well-ventilated area. Make sure that the air vents are not blocked and all doors can open freely. Step 2: Regulate the environment Do not place the all-in-one in direct sunlight or in an area that has abrupt temperature and humidity changes. The recommended ranges are 15 to 32.5°C (59 to 90.5°F) and 10 to 80% relative humidity. ENWW Step 1: Prepa
Краткое содержание страницы № 6
Краткое содержание страницы № 7
Step 4: Locate the all-in-one parts 5 4 6 3 2 7 1 1 tray 1 2 priority input slot 3 output bin 4 automatic document feeder (ADF) output bin 5 automatic document feeder (ADF) input tray 6 control panel 7 cartridge-door release 9 10 11 8 8 interface ports 9 security-lock slot 10 power switch 11 power connector ENWW Step 4: Locate the all-in-one parts 3
Краткое содержание страницы № 8
Step 5: Install the control-panel overlay (if not already installed) 1. Remove the adhesive backing from the overlay. 2. Align the bottom of the overlay with the bottom of the control panel, and make sure that the holes in the overlay align with the keys on the all-in-one. 3. Press the overlay from the bottom up toward the top until it is completely attached to the all-in-one. NOTE Make sure that the overlay is aligned correctly and is not pressing any buttons. The control panel includes the fol
Краткое содержание страницы № 9
Step 6: Install the media tray 1. Remove any shipping tape from the inside and outside of the tray. 2. Slide the tray in until it fits securely. 3. Open the top of the media input tray. 4. Slide out the media guides. 5. Pull out the long-media support. ENWW Step 6: Install the media tray 5
Краткое содержание страницы № 10
6. Place the media in the tray, and then adjust the media guides until they are flush with the media. NOTE Do not fan the media before placing it in the tray. 7. Close the top of the media input tray. 6 Chapter 1 Setting up the all-in-one ENWW
Краткое содержание страницы № 11
Step 7: Install the output bin support Insert the pin on one side of the support into the hole in the all-in-one. Flex the pin on the other side inward, and insert it into the hole. Step 8: Install the automatic document feeder (ADF) input tray 1. Align the two tabs on the input tray with the two grooves in the ADF lid. 2. Slide the tray into the grooves until the tray snaps into place. ENWW Step 7: Install the output bin support 7
Краткое содержание страницы № 12
Step 9: Install the ADF output support Insert the pin on one side of the support into the hole in the all-in-one. Flex the pin on the other side inward, and insert it into the hole. Step 10: Install the print cartridge 1. Press the cartridge-door release to open the print-cartridge door. 2. Remove the print cartridge from its packaging, and then rock the cartridge gently five or six times. 3. Bend the plastic tab at the end of the cartridge. 4. Pull the tab until all the sealing tape is removed
Краткое содержание страницы № 13
5. Hold the print cartridge by the handle and insert it into the all-in-one. 6. Close the print-cartridge door. CAUTION If toner gets on your clothing, wipe the toner off with a clean cloth, wash the items in cold water, and air dry. Hot water or heat from a dryer sets the toner in the fabric. NOTE Hewlett-Packard Company cannot recommend using non-HP print cartridges, whether they are new, refilled, or remanufactured. Because they are not HP products, HP cannot influence their design or control
Краткое содержание страницы № 14
Step 11: Connect the power cord 1. Connect the power cord to the power connector on the back of the all-in-one. 2. Connect the other end of the power cord to a grounded alternating current (AC) outlet. NOTE Use only the power cord that came with the all-in-one. Step 12: Connect a printer cable to the all-in-one NOTE If you are using the all-in-one as a standalone fax machine, go to step 14. If you are using it as a standalone copier, go to step 15. Connect the USB cable (A/B) cable to the correc
Краткое содержание страницы № 15
Step 13: Connect to a telephone line NOTE If you are not using the fax functionality, go to step 15. 1. Connect the included fax cord to the port on the all-in-one that is marked with an "L". 2. Connect the cord to a telephone jack. NOTE Use only the fax cord that came with the all-in-one. For more information about faxing, see the online User Guide. Step 14: Turn on the all-in-one Press the power switch on the back of the all-in-one. Hint If the all-in-one has no power and no lights are lit on
Краткое содержание страницы № 16
Step 15: Set the control-panel display language and location (if necessary) If prompted by the control panel, select your language and location. Follow the instructions on the control panel. NOTE The all-in-one automatically restarts after you select the location. Step 16: Test the hardware setup by printing a configuration report 1. Press Menu. 2. Use the < or the > button to select Reports, and then press . 3. Use the < or the > button to select Config report, and then press . Hint If the page
Краткое содержание страницы № 17
Step 17: Test the copier by using the automatic document feeder (ADF) 1. Load the configuration report that you just printed print-side down into the ADF input tray. 2. Adjust the media guides to sit against the page. 3. Press Start Copy. Hint If the copy job produces a blank page, make sure that the original is loaded print-side up and that no jams exist in the ADF and paper path. For information about removing jams and other troubleshooting tips, see the online User Guide. Step 18: Complete t
Краткое содержание страницы № 18
Step 19: Connect to a Windows computer (Windows only) The all-in-one software supports a full-featured installation for Windows 2000 and XP. Only print and scan functions are supported for Windows 98, Me, and Server 2003. NOTE To connect to a Macintosh computer, go to step 20. 1. Close all programs that are running on the computer. 2. Insert the software CD-ROM into the CD drive. If the installation program does not begin automatically, click Start, click Run, click Browse, select the HPSetup.ex
Краткое содержание страницы № 19
Step 20: Connect to a Macintosh computer (Mac OS X V10.3 and 10.4 only) 1. Connect the USB cable (A/B) to the Macintosh. 2. Close all of the programs that are running on the computer. 3. Insert the software CD-ROM into the CD drive. 4. In the CD folder, double-click the HP All-in-One Installer icon. 5. Follow the onscreen instructions, and then click Install. 6. When prompted, restart the computer. 7. When the HP All-in-One Setup Assistant starts, follow the instructions. ENWW Step 20: Connect t
Краткое содержание страницы № 20
Step 21: Fax setup If you installed the all-in-one software, the HP LaserJet Fax Setup Utility (Windows) or Setup Assistant (Mac) automatically runs. The software prompts you to set the time, date and fax header. In many countries/regions, this is a legal requirement. Hint If the utility does not run automatically, access it in the program group. If you are using the all-in-one as a standalone fax, complete the following steps: 1. Press Menu. 2. Use the < or the > button to select System Setup,
