ملخص المحتوى في الصفحة رقم 1
ENGLISH
OWNER’S MANUAL
MONITOR TV
Please read this manual carefully before operating
your set and retain it for future reference.
MONITOR TV MODELS
M2262D M2262DP
M2362D M2362DP
M2762D M2762DP
www.lg.com
ملخص المحتوى في الصفحة رقم 2
PREPARATION FRONT PANEL CONTROLS This is a simplified representation of the front panel. The image shown may be somewhat different from your set. P Po ow we er r IIn nd diic ca at to or r illuminates blue when the set is switched on. Note:You can adjust Power indicator in the OPTION menu. Headphone IR receiver Jack (Remote controller receiver) ENTER VOLUME CHANNEL Power INPUT MENU Button Buttons Buttons Button Button Button L Liig gh ht t S Se en ns so or r This is lens for light sensor sel
ملخص المحتوى في الصفحة رقم 3
VIDEO (MONO) AUDIO R L VIDEO AUDIO PREPARATION BACK PANEL INFORMATION This is a simplified representation of the back panel. The image shown may be somewhat different from your set. 1 6 2 3 4 5 COMPONENT AV-IN IN AV 1 AV 2 RS-232C IN Y (CONTROL & SERVICE) 1 PB S-VIDEO HDMI IN RGB IN (PC) ANTENNA/ 2 AC IN CABLE IN PR DVI-D IN (PC) L AC IN SERVICE AUDIO IN ONLY (RGB/DVI) OPTICAL R DIGITAL AUDIO OUT 7 8 9 12 10 11 1 6 Power Cord Socket S-Video Input This set operates on AC power. The voltage is
ملخص المحتوى في الصفحة رقم 4
N N E E P P O O < > PREPARATION STAND INSTALLATION The image shown may be somewhat different from your set. Carefully place the product screen side down on a Insert the S St ta an nd d B Ba as se e into the product. 1 2 cushioned surface that will protect product and screen from damage. S St ta an nd d B Ba as se e Turn the S St ta an nd d B Ba as se e L Lo oc ck k through 90° to fix the stand base t
ملخص المحتوى في الصفحة رقم 5
< > PREPARATION STAND INSTALLATION The image shown may be somewhat different from your set. Carefully place the product screen side down on a cushioned sur- 1 face that will protect product and screen from damage. Insert the S St ta an nd d B Ba as se e into the product. 2 S St ta an nd d B Ba as se e Use a C Co oiin n on the bottom of the stand base and turn the 3 screw clockwise to tighten. C Co oiin n 4
ملخص المحتوى في الصفحة رقم 6
N N N E E E P P P O O O < > PREPARATION DETACHING STAND The image shown may be somewhat different from your set. Detach the monitor to the S St ta an nd d B Ba as se e by Place the set screen side down on a cushion or 1 2 turning the screw to the left. soft cloth. S St ta an nd d B Ba as se e Turn the S St ta an nd d B Ba as se e L Lo oc ck k through 90° to separate the stand base from the stand body.
ملخص المحتوى في الصفحة رقم 7
< > PREPARATION DETACHING STAND The image shown may be somewhat different from your set. Place the set screen side down on a cushion or soft cloth. 1 Detach the stand base from the set by turning the screw to the 2 left with a coin. C Co oiin n Pull the stand base. 3 S St ta an nd d B Ba as se e 6
ملخص المحتوى في الصفحة رقم 8
PREPARATION DETACHING STAND BODY The image shown may be somewhat different from your set. Remove the Stand Body in the same way as the following when using it as a Wall Hook. < > 1. Remove the screw 2 point. 2. Pull the stand body. < > 1. Remove the screw 4 point. 2. Pull the stand body. 7
ملخص المحتوى في الصفحة رقم 9
PREPARATION WALL MOUNT: HORIZONTAL INSTALLATION For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Follow the instructions includ- ed with the wall mount. 1 10 0 c cm m 1 10 0 c cm m 1 10 0 c cm m 1 10 0 c cm m 1 10 0 c cm m DESKTOP PEDESTAL INSTALLATION For proper ventilation, allow a clearance of 10 cm on each side and from the wall. 1 10 0 c cm m 1 10 0 c cm m 1 10 0 c cm m 1 10 0 c cm m 8
ملخص المحتوى في الصفحة رقم 10
PREPARATION SWIVEL STAND(Only M2762D/M2762DP) The image shown may be somewhat different from your set. After installing the set, you can adjust the set manually to the left or right direction by 179 degrees to suit your viewing position. 179° 179° POSITIONING YOUR DISPLAY The image shown may be somewhat different from your set. Adjust the position of the panel in various ways for maximum comfort. • • T Tiillt t r ra an ng ge e -5° 15° 9
ملخص المحتوى في الصفحة رقم 11
PREPARATION LOCATION Position your set so that no bright light or sunlight falls directly onto the screen. Care should be taken not to expose the set to any unnecessary vibration, moisture, dust or heat. Also, ensure that the set is placed in a position to allow a free flow of air. Do not cover the ventilation openings on the back cover. If you intend to mount the set to a wall, attach the wall mounting interface (optional parts) to the back of the set. When you install the set using the wall mo
ملخص المحتوى في الصفحة رقم 12
PREPARATION SECURING THE SET TO THE WALL TO PREVENT FALLING WHEN THE SET IS USED ON A STAND(Only M2762D/M2762DP) Image shown may differ from your set. We recommend that you set up the set close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the set be attached to a wall so it cannot be pulled in a forward direction, potentially causing injury or damaging the product. Caution: Please make sure that children don’t climb on or hang from the set. Insert
ملخص المحتوى في الصفحة رقم 13
PREPARATION ATTACHING THE TV TO A DESK (Only M2762D/M2762DP) The image shown may be somewhat different from your set. The TV must be attached to desk so it cannot be pulled in a forward/backward direction,potentially causing injury or damaging the product.Use only an attached screw. 1-Screw (provided as parts of the product) Stand Desk ! WARNING G To prevent TV from falling over,the TV should be securely attached to the floor/wall per installation instructions. Tipping,shaking, or rocking the
ملخص المحتوى في الصفحة رقم 14
PREPARATION KENSINGTON SECURITY SYSTEM - The product is equipped with a Kensington Security System connector on the back panel. Connect the Kensington Security System cable as shown below. - For detailed installation and use of the Kensington Security System, refer to the user’s guide provided with the Kensington Security System. For further information, contact h ht tt tp p::/ // /w ww ww w..k ke en ns siin ng gt to on n..c co om m, the internet homepage of the Kensington company. Kensington se
ملخص المحتوى في الصفحة رقم 15
EXTERNAL EQUIPMENT SETUP To prevent equipment damage, never plug in any power cords until you have finished connecting all equipment. ANTENNA CONNECTION For optimum picture quality, adjust antenna direction. An antenna cable and converter are not supplied. AV 1 AV 2 Multi-family Dwellings/Apartments Wall AV 1 AV 2 ANTENNA/ (Connect to wall antenna socket) CABLE IN Antenna AC IN Socket AC IN RF Coaxial Wire (75 ) Outdoor Antenna (VHF, UHF) Single-family Dwellings /Houses (Connect to w
ملخص المحتوى في الصفحة رقم 16
AUDIO VIDEO EXTERNAL EQUIPMENT SETUP To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment. The image shown may be somewhat different from your set. HD RECEIVER SETUP When connecting with a component cable Connect the SET-TOP outputs to the C CO OM MP PO ON NE EN NT T IIN N V VIID DE EO O sockets (Y PB PR) on the set. 1 Connect the audio cable from the SET-TOP to C CO OM MP PO ON NE EN NT T IIN N A AU UD DIIO O sockets of the set.
ملخص المحتوى في الصفحة رقم 17
1 AUDIO IN HDMI IN (RGB/DVI) 2 AUDIO L R DVI OUTPUT EXTERNAL EQUIPMENT SETUP When connecting with a HDMI 1 Connect the HDMI output of the digital set-top box to the HDMI IN 1 H HD DM MII IIN N jack on the set. 2 1 When connecting with a HDMI to DVI cable H HD DM MII IIN N Connect the digital set-top box to jack on 1 the set. Connect the audio output of the digital set-top box to 2 A AU UD DIIO O IIN N ( (R RG GB B/ /D DV VII) ) the jack on the set. ( Turn on the digital set-top box. Refe
ملخص المحتوى في الصفحة رقم 18
VIDEO AUDIO EXTERNAL EQUIPMENT SETUP DVD SETUP When connecting with a component cable Connect the video output sockets (Y PB PR) of the DVD to the C CO OM MP PO ON NE EN NT T IIN N V VIID DE EO O 1 sockets (Y PB PR) of the set. Connect the audio cable from the DVD to C CO OM MP PO ON NE EN NT T IIN N A AU UD DIIO O sockets of the set. 2 Press the IIN NP PU UT T button to select C Co om mp po on ne en nt t. 3 Press the P PL LA AY Y button on the DVD. 4 The DVD playback picture appears on the
ملخص المحتوى في الصفحة رقم 19
S-VIDEO VIDEO L R VIDEO (MONO) L AUDIO R EXTERNAL EQUIPMENT SETUP When connecting S-Video Connect the S-Video output of the DVD to the S-Video in put on the set. 1 Connect the audio output of the DVD to the AUDIO in put on the set. 2 AV-IN S-VIDEO 1 2 When connecting HDMI cable 1 HDMI IN H HD DM MII IIN N Connect the HDMI output of the DVD to the 2 1 jack on the set. 1 ! NOTE HDMI supports video and audio. You do not need to connect a sperate audio cable. G If the DVD player does not support A
ملخص المحتوى في الصفحة رقم 20
EXTERNAL EQUIPMENT SETUP VCR SETUP To avoid picture noise (interference), leave an adequate distance between the VCR and the set. If a user uses 4:3 picture format for a long time, an afterimage may remain on the sides of the screen for a short time. When connecting with an antenna ANTENNA/ S-VIDEO VIDEO L R CABLE IN ANT OUT 1 OUTPUT ANT IN SWITCH Wall Jack 2 Antenna Connect the RF out socket of the VCR to the antenna socket of the set. 1 Connect the antenna cable to the RF aerial in socket
