ملخص المحتوى في الصفحة رقم 1
D-Link AirPlus
DWL-810+
2.4GHz Ethernet-to-Wireless Bridge
Manual
Building Networks for People
ملخص المحتوى في الصفحة رقم 2
Contents 1. Package Contents ............................................. 3 2. Introduction........................................................ 4 3. Wireless Basics ................................................. 7 4. Getting Started ................................................ 10 5. Web Configuration........................................... 12 6. Troubleshooting............................................... 18 8. Technical Specifications ..............................
ملخص المحتوى في الصفحة رقم 3
1. Package Contents Contents of Package: • D-Link AirPlus DWL-810+ Ethernet-to-Wireless Bridge • AC Power Adapter – 5V; 2.5A • Manual and Warranty on CD • Ethernet Cable (the DWL-810+ Auto MDI/MDIX Ethernet port works with straight-through or crossover cable) • Quick Installation Guide If any of the above items are missing, please contact your reseller. System Requirements for Configuration: • A computer with an Ethernet adapter. (We recommend that you use an Ethernet connectio
ملخص المحتوى في الصفحة رقم 4
2. Introduction The D-Link AirPlus DWL-810+ Ethernet-to-Wireless Bridge is a device that can be implemented in a variety of ways to provide wireless access by converting an Ethernet connection. For devices with a built-in Ethernet port, the DWL-810+ provides a cost effective way to gain wireless connectivity, virtually transforming wired devices into wireless units! Connect any Ethernet-enabled device to an existing 802.11b wireless network using the DWL-810+. Typical applications
ملخص المحتوى في الصفحة رقم 5
Features and Benefits • Transforms an Ethernet device into a wireless device • Up to 22Mbps transfer rates* • Fully compatible with standard 802.11b-compliant devices • Equipped with one 10/100 Ethernet port, Auto-MDI/MDIX • Quick and Simple connectivity via Ethernet • Supports Ad Hoc or Infrastructure modes • Easy web-based configuration when changing settings • Encryption to provide a level of security for data transfers LEDs LED stands for Light-Emitting Diode. The DWL-810+ ha
ملخص المحتوى في الصفحة رقم 6
Connections Ethernet Port – this RJ-45 Auto MDI/MDIX port provides Reset Button connection to a network device using a Cat 5 Ethernet cable. (The auto MDI/MDIX port accommodates either Straight- Through or Cross-Over cable and is auto-sensing.) Power Receptor Ethernet Port Reset Button – press this button to revert to the factory default settings of the DWL-810+ Power Receptor – connect one end of the 5V DC Power Adapter (included) to the power receptor on the DWL-810+ and conn
ملخص المحتوى في الصفحة رقم 7
3. Wireless Basics With the DWL-810+ you can provide instant wireless access to the LAN (Local Area Network) for Ethernet-enabled devices. With an Ethernet (CAT5) cable simply connect the DWL-810+ to the Ethernet port of a network device (such as a printer or web camera) to establish a wireless connection with another device equipped with a wireless network adapter set to Ad-Hoc mode. If you are planning a larger wireless network, D-Link offers a wide array of products for most of you
ملخص المحتوى في الصفحة رقم 8
Wireless Basics People use WLAN technology for many different purposes. Mobility - Productivity increases when people have access to data in any location within the operating range of the WLAN. Management decisions based on real-time information can significantly improve worker efficiency. Low Implementation Costs – WLANs are easy to set up, manage, change and relocate. Networks that frequently change, both physically and logically, can benefit from WLANs ease of implementation. WLANs
ملخص المحتوى في الصفحة رقم 9
Wireless Basics The DWL-810+ is also compatible with the following D-Link AirPlus family of products: DWL-650+ Enhanced 2.4GHz Wireless Cardbus Adapter for laptop PCs DWL-520+ Enhanced 2.4GHz Wireless PCI card for desktop PCs DWL-900AP+ Wireless Access Point DI-614+ Wireless Router Standards - Based Technology The IEEE standard-based technology assures that this product is interoperable with existing compatible wireless technology. This means you will be able to transfer larg
ملخص المحتوى في الصفحة رقم 10
Wireless Basics meters), at a 45-degree angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters) thick! Position Access Points and Adapters so that the signal will travel straight through a wall or ceiling (instead of at an angle) for better reception. 3. Building Materials can impede the wireless signal - A solid metal door or aluminum studs may have a negative effect on range. Try to position the DWL-810+, the Access Points, and computers
ملخص المحتوى في الصفحة رقم 11
Getting Started Setup #2: This example illustrates an Infrastructure setup. To connect the DWL-810+ to a wireless network with a wireless router or access point, please refer to the printed Quick Installation Guide included with the product. Web configuration is required to connect the DWL-810+ in Setup #2. Setup #2 DWL-810+ 11
ملخص المحتوى في الصفحة رقم 12
5. Web Configuration Before using the Web Configuration for the DWL-810+, please consider the following: You will need a JavaScript-enabled web-browser such as the Internet Explorer 6.0 or later, or the Netscape Navigator 6.0 or later. The computer that you are using for initial configuration must have an IP Address within the same range as the IP Address of the DWL- 810+. The DWL-810+ has a default IP Address of 192.168.0.30 with a subnet mask of 255.255.255.0 You will need to
ملخص المحتوى في الصفحة رقم 13
Configuration Menu Whenever you want to configure your network or the DWL-810+, you can access the Configuration Utility by opening the web-browser and typing in the IP Address of the DWL-810+. The DWL-810+ default IP Address is shown below: • Open the web browser • Type in the IP Address http://192.168.0.30 of the Access Point (The IP Address shown in the example above is the default setting. Use this IP address when connecting to a network consisting of other D-Link devices
ملخص المحتوى في الصفحة رقم 14
Configuration Menu Network This window displays the default settings of the DWL-810+. The default IP Address is 192.168.30. If you select Dynamic IP Address, you will obtain a dynamic IP Address from a DHCP server on your network. The Subnet Mask is 255.255.255.0. Input the IP Address of the Gateway (the router on your network.) Click Apply if you have made any changes. Operating Mode: Wireless Select Ad-hoc or Infrastructure. Infrastructure is the default sett
ملخص المحتوى في الصفحة رقم 15
Configuration Menu Channel: Channel 6 is the default channel. Input a new number if you want to change the default setting. All devices on the network must be set to the same channel to communicate on the network. WEP Encryption: Select Enable Encryption to use WEP (Wired Equivalent Privacy) on the network. All devices on the network, and the Access Point, must share the same WEP selection – either Enable or Disable, and they must share the same WEP key. The WEP key is generated from
ملخص المحتوى في الصفحة رقم 16
Configuration Menu Admin 1.5 Monday, December 30, 2002 Administrator Settings: Change your password in this window. Re-enter the new password to confirm. It can be up to 14 characters in length. Please keep a copy of your password in a safe place. Click Apply, if you have made any changes. System Settings: The current system settings can be saved as a file onto the local hard drive by cli
ملخص المحتوى في الصفحة رقم 17
Configuration Menu Help The Help window displays information about each window in the Configuration menu. When you change the settings in the Configuration menu, you will need to restart the DWL-810+ for the changes to take effect. 17
ملخص المحتوى في الصفحة رقم 18
6. Troubleshooting This section provides solutions to situations that can occur during the installation and operation of the DWL-810+ Ethernet-to-Wireless Bridge. Read the following descriptions if you are having problems. 1. How do I assign a Static IP Address in Windows XP/2000? Please note that Residential Gateways/Broadband Routers will automatically assign IP Addresses to the computers on the network, using DHCP (Dynamic Host Configuration Protocol) technology. If you are using
ملخص المحتوى في الصفحة رقم 19
How do I assign a Static IP Address in Windows XP/2000? (continued) • Right-click on Local Area Connections • Double-click Properties • Click on Internet Protocol (TCP/IP) • Click Properties • In the window below, select Use the following IP address • Input your IP address and subnet mask. (The IP Addresses on your network must be within the same range. For example, if one computer has an IP Address of 192.168.0.2, the other computer
ملخص المحتوى في الصفحة رقم 20
How do I assign a Static IP Address in Windows XP/2000? (continued) • IP Address: e.g., 192.168.0.2 • Subnet Mask: 255.255.255.0 • Default Gateway: Enter the LAN IP address of the wireless router. (D-Link wireless routers have a LAN IP address of 192.168.0.1) • Select Use the following DNS server address. Enter the LAN IP address of the Wireless Router. (D-Link wireless routers have a LAN IP address of 192.168.0.1) • Click OK You have completed the assignment of a Stat
