ملخص المحتوى في الصفحة رقم 1
VERTICAL HORIZON
VH-2402S
FAST ETHERNET SWITCH
MANAGEMENT GUIDE
9033645-01
ملخص المحتوى في الصفحة رقم 2
ملخص المحتوى في الصفحة رقم 3
Notice Only qualified personnel should perform installation procedures. NOTICE Enterasys Networks reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Enterasys Networks to determine whether any such changes have been made. The hardware, firmware, or software described in this manual is subject to change without notice. IN NO EVENT SHALL ENTERASYS NETWORKS BE LIABLE FOR ANY INCIDENTAL
ملخص المحتوى في الصفحة رقم 4
Notice ii 9033645-01
ملخص المحتوى في الصفحة رقم 5
TABLE OF CONTENTS 1. MANAGEMENT OVERVIEW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Configuration Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Required Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Console Port (Out-of-Band) Connections . . . . . . . . . . . . . . . . . . . . 1 Remote Management via the Console Port. . . . . . . . . . . . . . . . . . . 2 In-Band Connections .
ملخص المحتوى في الصفحة رقم 6
Displaying the Unicast Address Table . . . . . . . . . . . . . . . . . . . . . 62 Displaying the IP Multicast Registration Table . . . . . . . . . . . . . . . 63 Configuring Static Unicast Addresses. . . . . . . . . . . . . . . . . . . . . . 64 Resetting the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Logging Off the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 3. CONFIGURING & MONITORING THE SWITCH . . . . . . . . .
ملخص المحتوى في الصفحة رقم 7
Remapping Network Topology . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 APPENDIX B. VIRTUAL LANS (VLANS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 VLANs and Frame Tagging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 VH-2402S VLAN Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Assigning Ports to VLANs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Forwarding Tagged/Untagged Frames . . . . . .
ملخص المحتوى في الصفحة رقم 8
vi Table of Contents VH-2402S
ملخص المحتوى في الصفحة رقم 9
1. MANAGEMENT OVERVIEW Configuration Options For advanced management capability, the VH-SMGMT Vertical Horizon Management Module provides a menu-driven system configuration program. This program can be accessed by a direct or modem connection to the serial port on the Management Module (out-of-band), or by a Telnet connection over the network (in-band). The Management Module is based on SNMP (Simple Network Management Protocol). This SNMP agent permits a switch stack to be managed from any
ملخص المحتوى في الصفحة رقم 10
When attaching to a PC, set terminal emulation type to VT100, specify the port used by your PC (i.e., COM 1~4), and then set communications to 8 data bits, 1 stop bit, no parity, and 19200 bps (for initial configuration). Also be sure to set flow control to “none.” (Refer to “Configuring the Serial Port” on page 19 for a complete description of configuration options.) Remote Management via the Console Port Configure the Switch Site Connect the Management Module’s DB9 serial port to the modem
ملخص المحتوى في الصفحة رقم 11
In-Band Network Connection The on-board configuration program can be accessed using Telnet from any computer attached to the network. The switch and stack can also be managed by any computer using a Web browser (Internet Explorer 4.0 or above, or Netscape Navigator 4.0 or above), or from a network computer using network management software. 9033645-01 Management Overview 3
ملخص المحتوى في الصفحة رقم 12
4 Management Overview VH-2402S
ملخص المحتوى في الصفحة رقم 13
2. VH-2402S USER INTERFACE Overview Access is gained to the console menus by connecting a terminal to the console port (with a direct cable connection or over modems), or using Telnet to access the Management Module over the network. These menus allow you to reconfigure the switch, as well as to monitor the status and performance of the switch or the attached stack. The menus have a layout similar to the sample Main Menu shown in Figure 2-1. The information is divided into the following pa
ملخص المحتوى في الصفحة رقم 14
User Access Once a direct connection to the serial port or a Telnet connection is established, the login screen for the on-board configuration program . You may need to press Enter a few times to display the screen. appears The default user names are “admin” and “guest,” with no passwords. The administrator has Read/Write access, which allows you to read and modify switch information. The guest has Read Only access to the management program, which allows you to view switch information, but
ملخص المحتوى في الصفحة رقم 15
Factory Defaults Table 2-1 lists the default settings for switch configuration parameters. Each parameter can be changed via the console menus or Telnet. Table 2-1. Factory Default Settings Parameter Default Value Multicast Filtering GMRP Disabled IGMP Multicast Filtering Disabled Port Configuration Flow Control Disabled Speed and Duplex Auto Admin Enabled Broadcast Storm Control Enabled - 500 pps Port Priority Default Ingress User Priority 0 Spanning Tree Algorithm Active Aging Time 300 Bri
ملخص المحتوى في الصفحة رقم 16
Parameter Default Value Virtual LANs Acceptable VLAN Frame Type All Configurable PVID Tagging Yes GVRP Disabled Untagged VLAN Group Assignment 1 VLAN Ingress Filtering False VLAN Learning SVL 8 VH-2402S User Interface VH-2402S
ملخص المحتوى في الصفحة رقم 17
Main Menu The Main Menu is the first screen seen after successfully logging into the system. Figure 2-2 shows the Main Menu and the accompanying table . describes the Main Menu Vertical Horizon Local Management -- VH-2402S Main Menu System Information Menu... Management Setup Menu... Device Control Menu... Network Monitor Menu... System Restart Menu... Exit Use or arrow keys to move. to select. Figure 2-2. Main Menu Selection Description System Information Menu System Informati
ملخص المحتوى في الصفحة رقم 18
Selection Description Device Control Menu Port Configuration Enables any port, enables/disables flow control, and sets communication mode to auto-negotiation, full duplex or half duplex. Port Information Displays operational status, including link state, flow control method, and duplex mode. Spanning Tree Enables Spanning Tree Algorithm; also sets parameters for Configuration hello time, maximum message age, switch priority, and forward delay; as well as port priority and path cost. Spanni
ملخص المحتوى في الصفحة رقم 19
Selection Description IP Multicast Displays all the multicast groups active on this switch, Registration Table including multicast IP addresses and corresponding VLAN IDs. Static Unicast Address Used to manually configure host MAC addresses in the Table Configuration unicast table. System Restart Restarts system with options to use POST, or to retain factory defaults, IP settings, or user authentication settings. Exit Exits the configuration program. System Information Menu Use the System
ملخص المحتوى في الصفحة رقم 20
Displaying System Information Use the System Information screen to display descriptive information about the switch, or for quick system identification as shown in the following figure and table. Vertical Horizon Local Management -- VH-2402S System Information System Description : Vertical Horizon VH-2402S System Object ID : 1.3.6.1.4.1.52.3.9.1.10.7 System Up Time : 48067 (0 day, 1 hr, 2min, 34 sec) System Name : DEFAULT SYSTEM NAME System Contact : DEFAULT SYSTEM CONTACT Syste
