ملخص المحتوى في الصفحة رقم 1
GROUTHOG
TILE AND GROUT MACHINE
Operating Instructions (ENG)
MODEL: GH3 (115V)
10050060
Read instructions before operating the machine.
N
86038000 07/14/08
PRV NO. 98108
ملخص المحتوى في الصفحة رقم 2
SAFETY IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. To reduce the risk of fire, electric shock, or injury: ! WARNING: Use only indoors. Do not use outdoors or expose to rain. Use only as described in this manual. Use only manufacturer’s recommended components and attachments. If the machine is not working properly, has been dropped, da
ملخص المحتوى في الصفحة رقم 3
SAFETY This appliance is for use on a nominal 120-volt INSPECTION circuit, and has a grounded plug that looks like the Please carefully unpack and inspect your plug in “Fig. A” below. A temporary adaptor that GROUTHOG for shipping damage. Each unit is looks like the adaptor in “Fig. C” below may be used operated and thorougly inspected before shipment, to connect this plug to a 2-pole receptacle as shown and any damaged is the responsibliltiy of the in “Fig. B” below, if prope
ملخص المحتوى في الصفحة رقم 4
OPERATION The brush-drive motor is SELECT THE RIGHT CHEMICAL FOR THE JOB: thermally protected and should an overload condition occur causing the 1. For greasy or oily soil – Use a heavy-duty motor to stop, the machine will not start until the degreaser. “ON” switch is depressed. 2. For sealer or old wax - Use a heavy-duty 8. Start cleaning at the farthest corner and work stripper. toward the door. For best results, pull machine backwards at a steady pace. 3. For soap r
ملخص المحتوى في الصفحة رقم 5
MAINTENANCE DAILY MAINTENANCE BEARING REPLACEMENT 1. Before storing the machine, clean exterior. Using a small torch, heat the aluminum bearing block Remove brush and rinse clean with hot water. just enough to allow the bearing and shaft (items 31 and 32, respectively) to be removed. 2. Periodically inspect electrical cable and connections. Because the cable will lie on wet, Use a bearing puller to remove old bearing. When abrasive floors, the cable must be well insulated. rep
ملخص المحتوى في الصفحة رقم 6
WIRING DIAGRAM 115V GH3 BLACK 86268310 PRV NO. 88240 BLACK 86268150 PRV NO. 88165 BLACK 86268600 PRV NO. 88421 BLACK 86268150 PRV NO. 88165 BLACK 86268170 PRV NO. 88618 BLACK 86268150 PRV NO. 88165 GROUTHOG 86038000 05/17/07 6
ملخص المحتوى في الصفحة رقم 7
THIS PAGE LEFT BLANK INTENTIONALLY GROUTHOG 86038000 05/17/07 7
ملخص المحتوى في الصفحة رقم 8
GROUT HOG ASSEMBLY 78 62 66 69 71 81 67 70 77 61 76 65 63 80 68 64 69 72 63 64 75 73 79 39 60 10 74 51 50 59 52 58 45 53 49 42 45 56 28 57 55 38 48 54 39 16 14 FRAME 41 15 47 42 46 17 30 4 5 18 20 13 28 17 3 19 40 18 1 4 43 23 18 31 22 44 30 7 38 2 45 37 21 12 3 3 6 25 22 30 30 3 9 33AB 10 24 28 35 34 27 6 29 32 23 FRAME 26 10 31 11 35 GROUTHOG 86038000 07/14/08 8
ملخص المحتوى في الصفحة رقم 9
GROUT HOG ASSEMBLY SERIAL NO. REF PART NO. PRV NO. DESCRIPTION NOTES: FROM 1 86278140 70002 SHOULDER BOLT, 3/8 OD X 2.0 L 2 86259660 89038 WHEEL, GH 4" DIA. 3 86010680 87030 WASHER, 3/8 ID X 3/4 OD NYLON 4 86278910 87003 WASHER, 3/8 ID X 7/8 OD SS 5 86005750 57113 NUT, 5/16-18 HEX NYLOCK 6 86274050 70078 SCR, 5/16 X 3/8 PHSB PH SS DL 7 86091970 14222 BRKT ASM, GH HANDLE ADJ. 8 - OPEN - 9 86226780 73044 SPRING, EXT .44 D X 2.25 L X .054 W 10 86005720 57106 NUT, 1/4-
ملخص المحتوى في الصفحة رقم 10
GROUT HOG ASSEMBLY SERIAL NO. REF PART NO. PRV NO. DESCRIPTION NOTES: FROM 49 86092320 34111 FRAME, GH3 MAIN 50 86090390 89037 WEIGHT, GROUT HOG COUNTERBALANCE 51 86251350 67064 RELAY, 120V SPDT 52 86197560 40015 HOSEBARB, 1/4 FPT X 3/8 53 86237150 35065 GASKET, GH3 COVER 54 86076200 36051 GUSSET, GH3 55 86279090 87067 WASHER, 5/16 LOCK INT. STAR PLT 56 86277940 70126 SET SCR, 1/4-28 X 1/4 KCP DL 57 86229270 11011 BELT, GH3 DRIVE 58 86250430 64028 PULLEY, GH MOTOR 1
