ملخص المحتوى في الصفحة رقم 1
User’s Guide
L1954T/L1954TQ
Make sure to read the Important Precautions before using the product.
Keep the User's Guide(CD) in an accessible place for future reference.
See the label attached on the product and give the information to your
dealer when you ask for service.
ملخص المحتوى في الصفحة رقم 2
Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national stan
ملخص المحتوى في الصفحة رقم 3
Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation. If these openings are blocked, built-up heat can cause failures wh
ملخص المحتوى في الصفحة رقم 4
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand 1. Place the monitor with its front facing downward on a soft cloth. 2. Assemble the Stand Body into the product in the correct direction as shown in the picture. Stand Body Hinge Body 3. Assemble the Stand Base(Front, Rear) into the Stand Body in the correct direction. Stand Body Stand Base 4. Insert the Cable Deco Cove
ملخص المحتوى في الصفحة رقم 5
Connecting the Display Disassembling the stand 1. Put a cushion or soft cloth on a flat 2. Place the monitor face down on surface. the cushion or soft cloth. 3. Slide the Cable Deco Cover out from the stand body. 4. Nip Latch inside, Take off the stand base from stand body. 5. Please pull the stand body lightly to separate it from the hinge body. A4
ملخص المحتوى في الصفحة رقم 6
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range: -5˚~20˚ Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. A5
ملخص المحتوى في الصفحة رقم 7
Connecting the Display Using the Computer 1. Make sure to turn off the computer and product. Connect the cable as below sketch map form 1 to 2 . A Connect DVI Cable B Connect Dsub Cable (PC) C Connect Dsub Cable (Mac) Power Cord Signal Cable Analog signal Digital signal D-sub DVI Fix the power cord & signal cable as shown in the picture. Wall-outlet type PC-outlet type DVI-D(This feature is not available in all countries.) Mac adapter For Apple Macintosh use, a separate plug adapter is needed
ملخص المحتوى في الصفحة رقم 8
Control Panel Functions Front Panel Controls At the current display, Use 'ez Zooming' Key, then the display resolution is transferred to the one step low resolution. Use 'ez Zooming' Key one more, the display is back to the original display. *Only One touch of ez-zoom, you can fine the best resolution you want and it is possible to magnify the size of characters and pictures for the old not having good eye sight, housewives not dealing with computer well and children. The resolutions at which th
ملخص المحتوى في الصفحة رقم 9
Control Panel Functions Use these buttons to select or adjust functions in the On - + Buttons Screen Display. For more information, refer to page A14. Use this button to make D-Sub or DVI connector active. This feature is used when two computers are connected to the display. The default setting is D-Sub. Use this button to enter a selection in the On Screen AUTO/SET Display. Button AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press the AUTO/SET button before entering the O
ملخص المحتوى في الصفحة رقم 10
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making image adjustments. To make a
ملخص المحتوى في الصفحة رقم 11
On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. Main menu Sub-menu A D Reference BRIGHTNESS PICTURE To adjust the brightness, contrast and gamma of the CONTRAST screen GAMMA sRGB To customize the color of COLOR PRESET 6500K the screen 9300K RED GREEN BLUE To adjust the position of the HORIZONTAL screen POSITION VERTICAL CLOCK To improve the clarity and PHASE TRACKING stabilit
ملخص المحتوى في الصفحة رقم 12
On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears. PICTURE Menu Name Sub-menus Icons Button Tip MENU : Exit : Adjust (Decrease/Increase) SET : Enter : Select another sub-menu NOTE OSD (On Screen Display) menu languages on the monitor
ملخص المحتوى في الصفحة رقم 13
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description PICTURE PICTURE BRIGHTNESS To adjust the brightness of the screen. To adjust the contrast of the screen. CONTRAST GAMMA Set your own gamma value. : -50/0/50 On the monitor, high gamma values display whitish images and low gamma values display high contrast images. MENU : Exit : Decrease : Increase SET : Select another sub-menu COLOR COLOR • sRGB: Set the screen color to fit the PRESET SRGB standard color specificat
ملخص المحتوى في الصفحة رقم 14
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description TRACKING TRACKING CLOCK To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. PHASE To adjust the focus of the display. This item allows you to remove any horizontal noise and clear or sharpen the image of characters. MENU : Exit : Decrease : Increase SHARPNESS To adjust the clearness of the screen. SET : Select another sub-menu SETUP To choose the la
ملخص المحتوى في الصفحة رقم 15
On Screen Display(OSD) Selection and Adjustment The OSD screen will appear when you touch the button at the bottom of the monitor. Menu Name Icons Sub-menu Name FLATRON F-ENGINE Screen when applied Screen when not applied When you execute F-ENGINE, two tones will appear on the screen as shown. The applied screen will appear on the left side, whereas the non-applied screen will appear on the right side.Touch the SET button to use the adjusted screen. Main menu Sub menu Descript
ملخص المحتوى في الصفحة رقم 16
Troubleshooting Check the following before calling for service. No image appears No image appears ● Is the power cord of the • Check and see if the power cord is connected display connected? properly to the power outlet. ● Is the power indicator • Press the Power button. light on? • Adjust the brightness and the contrast. ● Is the power on and the power indicator blue or green? ● Is the power indicator • If the display is in power saving mode, try moving the mouse or pressing any key on the keyb
ملخص المحتوى في الصفحة رقم 17
Troubleshooting Display image is incorrect ● Display Position is • Press the AUTO/SET button to automatically incorrect. adjust your display image to the ideal setting. If the results are unsatisfactory, adjust the image position using the H position and V position icon in the on screen display. • Check Control Panel --> Display --> Settings and see if the frequency or the resolution were changed. If yes, readjust the video card to the recommend resolution. • Press the AUTO/SET button to automa
ملخص المحتوى في الصفحة رقم 18
Troubleshooting Have you installed the display driver? ● Have you installed the • Be sure to install the display driver from the display driver CD (or diskette) that comes with your display driver? display. Or, you can also download the driver from our web site: http://www.lge.com. • Make sure to check if the video card supports ● Do you see an Plug&Play function. "Unrecognized monitor, Plug&Play (VESA DDC) monitor found" message? A17
ملخص المحتوى في الصفحة رقم 19
Specifications Display 19 inches (48.19 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating 19 inches viewable 0.294 mm pixel pitch Horizontal Freq. Analog : 30 - 83 kHz (Automatic) Sync Input Digital : 30 - 71 kHz (Automatic) Vertical Freq. 56 - 75 Hz (Automatic) Input Form Separate TTL, Positive/Negative SOG (Sync On Green) Digital Video Input Signal Input 15 pin D-Sub Connector DVI - D connector (Digital) Input Form RGB Analog (0.7 Vp-p/ 75 ohm), Digital Max Analog : VESA 1280 x 1024
ملخص المحتوى في الصفحة رقم 20
Specifications Preset Modes (Resolution) Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz) 1 VGA 31.469 640 x 350 70 2 VGA 31.468 720 x 400 70 3 VGA 31.469 640 x 480 60 4 VESA 37.500 640 x 480 75 5 VESA 37.879 800 x 600 60 6 VESA 46.875 800 x 600 75 7 MAC 49.725 832 x 624 75 8 VESA 48.363 1024 x 768 60 9 VESA 60.023 1024 x 768 75 10 MAC 68.681 1152 x 870 75 11 VESA 61.805 1152 x 900 65 *12 VESA 63.981 1280 x 1024 60 **13 VESA 79.976 1280 x 1024 75 * Recommend Mode ** Only Ana
