Resumen del contenido incluido en la página 1
IP CAMERA
INSTRUCTIONS
VN-V25U
(Setting)
VN-V26U
VN-X35U
VN-V225U series
VN-X235U series
Thank you for purchasing this JVC product.
Before operating this unit, please read the
instructions carefully to ensure the best
possible performance.
LST0886-001A
Resumen del contenido incluido en la página 2
Getting Started Operation Contents Operation of Built-in Viewer...................... 66 Screen Configuration........................... 66 lmage Settings..................................... 68 Getting Started PTZ Settings........................................ 70 Contents ................................................... 2 PTZ Control ......................................... 72 JPEG Viewer Settings ......................... 74 Network Settings MPEG4 Viewer Settings...................... 76
Resumen del contenido incluido en la página 3
Network Settings VFS(Variable File Size) Network Requirements (TX) is applicable to VN-X series only. Distribution File Size ● Ensure that there is sufficient network (typical sizes) bandwidth for the data volume to be sent out by camera. Do not send multicast stream that Quad VGA QVGA exceeds the bandwidth. If the entire bandwidth (TX) is used by the multicast stream, control of this Setting 1 (High) 180 KB 80 KB 27 KB camera via the network may fail. Values ● Data volume to be sent by
Resumen del contenido incluido en la página 4
Network Settings ● When both JPEG and MPEG4 images are distributed Network Requirements When both JPEG and MPEG4 images are distributed simultaneously, distribution up to two clients for JPEG (continued) and three clients for MPEG4 respectively is possible. However, distribution requests that exceed a total bit rate of 20 Mbps will be denied. Bit Rate of Audio Maximum number of distributions when JPEG and Only 1 audio data stream can be received. Data volume MPEG4 data is distributed for
Resumen del contenido incluido en la página 5
● When both JPEG and MPEG4 images are distributed When both JPEG and MPEG4 images are distributed, Packet Loss distribution works in the same way as frame rate priority When acquiring images from camera via TCP, mode if the distribution request would be accepted in the packet loss may be recovered by TCP frame rate priority mode. If the distribution request would transmission. When there is considerable delay be denied in the frame rate priority mode, the frame rate in the network, howeve
Resumen del contenido incluido en la página 6
Network Settings Set up the computer for setting the IP IP Address Settings address. ● Minimum computer specifications for setting OS : Windows XP (Professional or IP address setting procedure Home Edition) (SP2) Web browser Follow the procedure below to configure the IP : Internet Explorer Version 6.0 address of the camera. XP : Version 6.0 Step1 IP address setting at the Vista : Version 7.0 computer Note: (APage
Resumen del contenido incluido en la página 7
IP address setting at the computer Set the computer to an IP address that enables communication with the camera. Procedures described in this item are intended for Windows XP users. 1. Click [Start] ● Select in the sequence of [Control Panel]-[Network Connection]-[Local Area]. Windows Vista : ● Select in the sequence of [Settings]-[Control Panel]-[Network and Sharing Center]-[Manage network connections]. 2. The computer on which Internet Explorer is launched automatically selects the connected
Resumen del contenido incluido en la página 8
Network Settings IP Address Settings (continued) Internet Explorer Setting 1. Launch the Internet Explorer on the computer 2. When proxy settings are enabled in the Internet Explorer, follow the steps below to disable the proxy of the Internet Explorer ● Select in the order of [Tool]-[Internet Options]-[Connections]-[LAN Setting], followed by deselecting the check for [Use a proxy server for your LAN] under [Proxy Server] of the [Local Area Network (LAN) Settings] window. Deselect the check
Resumen del contenido incluido en la página 9
4. If ActiveX controls and plug-ins of the Internet Explorer is disabled, follow the steps below to enable it ● Click [Trusted sites] under [Tool]-[Internet Options]-[Security]. Select the [Custom Level] button and open the [Security Settings] window. Set all items under [ActiveX controls and plug-ins] in the opened window to [Enable]. Enable also [Allow Script-initiated window without size or position constraints.] under [Miscellaneous]. Select [Enable] 5. Disable pop-up block Connection of
Resumen del contenido incluido en la página 10
Network Settings IP Address Settings (continued) Connecting the camera to the computer 1. Launch the Internet Explorer Click [Go]. Enter the following IP address into the address field. B A http://192.168.0.2 Memo: ● If the proxy server settings for access to the Internet via the Internet Explorer is enabled, you may not be able to specify the IP address directly.
Resumen del contenido incluido en la página 11
3. Built-in Viewer of camera is displayed 4. The operator password entry screen appears A B A Enter the password (default is AjvcB) of AoperatorB authority. B Click [OK]. Memo: ● The operator password entry screen does not appear if the password is stored on the computer. Proceed to configure the IP address setting for the camera. (A Page 12)
Resumen del contenido incluido en la página 12
Network Settings IP Address Settings (continued) IP address setting for the camera 1 Click [Details] of the camera Built-in viewer Click 2 The [Basic Settings1] screen appears C Click A Set the [IP Setting] item to [DHCP Disable]. Enter the values you wish to specify in the [IP Address], [Subnet Mask] and [Default Gateway] fields. B Select the [Time Zone]. A Set the [IP Setting]. ● When selecting ADHCP DisableB: Select ADHCP DisableB, and specify a value in the [IP Address], [Subnet Mask]
Resumen del contenido incluido en la página 13
B Select the [Time Zone]. C Click [OK]. 3 A confirmation screen appears Click [OK]. Camera restarts using the new IP address. It takes about one minute for the camera to reboot. Memo: ● Access from the connected computer may fail when the IP address of the camera is changed. To enable access to camera from the same computer, alter the IP address at the computer acc
Resumen del contenido incluido en la página 14
Network Settings Pages that users have access to Enter user name and password Restrictions are placed on the pages that users have access to. In addition, links on the web User name and password entry will be required pages are also displayed according to the at the beginning. access authority of the user. There are three access authorization levels to ● admin camera. The factory settings are as follows. (TX) is applicable to VN-X series only. User Default Authorization Name Password lev
Resumen del contenido incluido en la página 15
● operator (TX) is applicable to VN-X series only. Basic Settings2 [Camera] [Encoding] [JPEG] [MPEG4] Details [Camera] [Encoding] [Audio] (This feature is not available in VN-V25U) [Alarm] [Alarm Environment] [PTZ] (TX) [Auto Patrol] (TX) [Privacy Mask] [Motion detection] [Streaming] [LED Settings] [Miscellaneous] [Operation] [Settings] [Position List] (TX) [Patrol Settings] (TX) ● user Details [Miscellaneous] Memo: ● The [Security Setting
Resumen del contenido incluido en la página 16
Setting Using Internet Explorer Setting How to open the setting page 1. Enter IP address of camera in the address bar of Internet Explorer (A Page 10) A unified viewer is opened. Click 2. Click [Details]. ● [Basic Settings1] page will be opened if accessed by user name AadminB. (A Page 17) ● [Basic Settings2] page will be opened if accessed by user name AoperatorB. (A Page 18) ● [Miscellaneous] page will be opened if accessed by user name AuserB. (A Page 59) 16
Resumen del contenido incluido en la página 17
Basic Settings1 This page is for performing basic setting related to the network. This page can be used during access using AadminB. ● Click [Basic Settings1]. ● Press the [OK] button to enable the new settings. ● If the [OK] button is pressed upon entering an invalid value, a warning message will appear and the entry will be denied. Press the [Cancel] button to restore the invalid entry to the current value. Click A B C D E F Memo:
Resumen del contenido incluido en la página 18
Setting Using Internet Explorer Setting (continued) Basic Settings2 Page for setting fundamental parameters of ACameraB, AJPEGB and AMPEG4B. This page can be used during access using AadminB or AoperatorB. ● Click [Basic Settings2]. ● Press the [OK] button to enable the new settings. ● If the [OK] button is pressed upon entering an invalid value, a warning message will appear and the entry will be denied. Press the [Cancel] button to restore the invalid entry to the current value. Click A B C
Resumen del contenido incluido en la página 19
(TV) is applicable to VN-V series only. (TX) is applicable to VN-X series only. A Camera ID Character strings entered here will be written to the JPEG comment segment (item name: camera). Refer to the API Guide on the file formats of JPEG. B Monitor Type For selecting the monitor type according to the monitor used to display the video images. The picture quality varies according to the type of monitor selected. Custom : Enables setting of picture quality according to the user's preference. D
Resumen del contenido incluido en la página 20
Setting Using Internet Explorer Setting (continued) Basic Settings2 (continued) (TV) is applicable to VN-V series only. (TX) is applicable to VN-X series only. DJPEG Frame Size For specifying the JPEG picture quality (rate control mode) and size (target file size). When AVFS1B to AVFS7B is selected, the quantization table during JPEG encoding will be maintained and the file size will increase/decrease according to the input signals. Typical sizes will be displayed in the Size field. When reco
