Resumen del contenido incluido en la página 1
KV-85
AMD Athlon 64 System Board
Socket 754
Users Manual
Rev. 1.01
Resumen del contenido incluido en la página 2
Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special, inciden
Resumen del contenido incluido en la página 3
Table of Contents Chapter 1. Introduction .......................................................................... 1-1 1-1. Features & Specifications ........................................................................1-1 1-2. Layout Diagram .......................................................................................1-3 Chapter 2. Hardware Setup.................................................................... 2-1 2-1. Install The Motherboard............................
Resumen del contenido incluido en la página 4
Chapter 4. Driver Installation ................................................................ 4-1 4-1. Setup Items...............................................................................................4-2 Appendix A. How to Get Technical Support............................................. A-1 KV-85
Resumen del contenido incluido en la página 5
Introduction 1-1 Chapter 1. Introduction 1-1. Features & Specifications 1. CPU • Supports AMD Socket 754 Athlon 64/Sempron Processor with 1600MHz Hyper-Transport • Supports AMD K8 CPU Cool n Quiet Technology 2. Memory • 2 x 184-pin DIMM sockets • Supports DDR400/333 Un-buffered ECC/ Non-ECC memory • Supports maximum memory capacity up to 2GB 3. Chipset • VIA K8M800 + VT8237R 4. Graphics • Integrated UniChrome Pro Graphics with 2D/3D/Video controller 5. SATA RAID • Serial ATA 1.5
Resumen del contenido incluido en la página 6
1-2 Chapter 1 9. Back Panel I/O • 1x PS/2 keyboard, 1x PS/2 mouse • 1x Parallel Port, 1x Serial Port, • 1x VGA Connector • 4x USB 2.0 Connectors • 1x RJ-45 LAN Connector • 1x Audio connector (Line-out, Line-in, MIC-in) 10. Miscellaneous • mATX form factor: 244 x 244 mm ! Specifications and information contained herein are subject to change without notice. KV-85
Resumen del contenido incluido en la página 7
Introduction 1-3 1-2. Layout Diagram Users Manual
Resumen del contenido incluido en la página 8
1-4 Chapter 1 KV-85
Resumen del contenido incluido en la página 9
Hardware Setup 2-1 Chapter 2. Hardware Setup Before the Installation: Turn off the power supply switch (fully turn off the +5V standby power), or disconnect the power cord before installing or unplugging any connectors or add-on cards. Failing to do so may cause the motherboard components or add-on cards to malfunction or damaged. 2-1. Install The Motherboard Most computer chassis have a base with many mounting holes to allow motherboard to be securely attached on and at the same time, pr
Resumen del contenido incluido en la página 10
2-2 Chapter 2 2-2. Install CPU, Heatsink and Fan Assembly Please pay attention to the following notices before installing the CPU and heatsink/fan assembly. 1. Always use the processor with the Heatsink and Fan Assembly installed. 2. Do not touch the pins on the processor. 3. If you ever need to reinstall the Heatsink and fan Assembly, please clean the heatsink surface and apply new thermal interface material first. 3. Lower the locking lever to the fully locked position. 1. Pu
Resumen del contenido incluido en la página 11
Hardware Setup 2-3 6. On the other side, push the retention clip straight down to lock into the plastic lug on the retention frame. 7. Turn the cam lever to lock into the retention frame. 8. Attach the four-pin power plug from the heatsink and fan assembly to the CPU FAN connector. For detailed information on how to install your heatsink and fan assembly, please refer to the instruction manual came packed with the heatsink and fan assembly you bought. Users Manual
Resumen del contenido incluido en la página 12
2-4 Chapter 2 2-3. Install System Memory This system board provides two 184-pin DDR DIMM slots for DDR400 memory modules with memory expansion size up to 2GB. Bank Memory Module Total Memory Bank 0, 1 (DIMM1) 256MB, 512MB, 1GB 256MB ~ 1GB Bank 2, 3 (DIMM2) 256MB, 512MB, 1GB 256MB ~ 1GB Total System Memory 256MB ~ 2GB NOTE: Usually there is no hardware or BIOS setup require after adding or removing memory modules, but you will have to clear the CMOS memory first if any memory module
Resumen del contenido incluido en la página 13
Hardware Setup 2-5 2-4. Connectors, Headers and Switches Here we will show you all of the connectors, headers and switches, and how to connect them. Please read the entire section for necessary information before attempting to finish all the hardware installation inside the computer chassis. A complete enlarged layout diagram is shown in Chapter 1 for all the position of connectors and headers on the board that you may refer to. WARNING: Always power off the computer and unplug the AC powe
Resumen del contenido incluido en la página 14
2-6 Chapter 2 (2). FAN Connectors These 3-pin connectors each provide power to the cooling fans installed in your system. The CPU must be kept cool by using a powerful fan with heatsink. The system is capable of monitoring the speed of the CPU fan. • CPUFAN1: CPU Fan Power Connector • CASFAN1: Auxiliary Fan Power Connector WARNING: These fan connectors are not jumpers. DO NOT place jumper caps on these connectors. KV-85
Resumen del contenido incluido en la página 15
Hardware Setup 2-7 (3). CMOS Memory Clearing Header This header uses a jumper cap to clear the CMOS memory. • Pin 1-2 shorted (default): Normal operation. • Pin 2-3 shorted: Clear CMOS memory. WARNING: Turn the power off first (including the +5V standby power) before clearing the CMOS memory. Failing to do so may cause your system to work abnormally or malfunction. Users Manual
Resumen del contenido incluido en la página 16
2-8 Chapter 2 (4). Front Panel Switches & Indicators Headers These headers are used for connecting switches and LED indicators on the chassis front panel. Watch the power LED pin position and orientation. The mark + align to the pin in the figure below stands for positive polarity for the LED connection. Please pay attention to connect these headers. A wrong orientation will only cause the LED not lighting, but a wrong connection of the switches could cause system malfunction. • S
Resumen del contenido incluido en la página 17
Hardware Setup 2-9 (5). Additional USB Port Headers These headers each provide 2 additional USB 2.0 ports connection through an USB cable designed for USB 2.0 specifications. Pin Pin Assignment Pin Pin Assignment 1 VCC 2 VCC 3 Data0 - 4 Data1 - 5 Data0 + 6 Data1 + 7 Ground 8 Ground 9 NC 10 NC Users Manual
Resumen del contenido incluido en la página 18
2-10 Chapter 2 (6). Front Panel Audio Connection Header This header provides the connection to audio connector at front panel. • To use the audio connector at front panel, remove all the jumpers on this header, and then connect to front panel by the extension cable provided with the chassis. • To use the audio connector at rear panel, disconnect the extension cable, attach the jumpers back at pin 5-6, and pin 9-10 (default setting). Pin Pin Assignment Pin Pin Assignment 1 Audio Mic
Resumen del contenido incluido en la página 19
Hardware Setup 2-11 (7). Serial ATA Connectors These connectors are provided to attach one Serial ATA device at each channel via Serial ATA cable. Users Manual
Resumen del contenido incluido en la página 20
2-12 Chapter 2 (8). Accelerated Graphics Port Slot This slot supports an optional AGP graphics card up to AGP 8X mode. ATTENTION: This motherboard does not support 3.3V AGP cards. Use only 1.5V or 0.8V AGP cards. (9). Internal Audio Connectors These connectors connect to the audio output of internal CD-ROM drive or add-on card. KV-85
