Resumen del contenido incluido en la página 1
User’s Guide
L192WS
LCD Computer Monitor
Make sure to read the Important Precautions before using this product.
Keep the User's Guide(CD) in an accessible place for furture reference.
Have the model and serial number ready when calling for support.
Resumen del contenido incluido en la página 2
Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national stan
Resumen del contenido incluido en la página 3
Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation. If these openings are blocked, built-up heat can cause failures wh
Resumen del contenido incluido en la página 4
REAR REAR FRONT FRONT Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand 1. Place the monitor with its front facing downward on a soft cloth. 2. Assemble the Stand Body into the product in the correct direction as shown in the picture. Make sure you push it until you hear it “click”. 3. Assemble the Stand Base(Front, Rear) into the Stand Body in the correct directio
Resumen del contenido incluido en la página 5
Connecting the Display To remove the Stand: 1. Put a cushion or soft cloth on a flat surface. 2. Place the monitor face down on the cushion or soft cloth. The Head part The Stand base part 3. Hold the product as it follows and lift up the Stand slightly. 4. Change your hold on the product as it follows and turn the Stand Base in the arrow direction until you hear a "click." 5. Pull out the Stand to remove. A4
Resumen del contenido incluido en la página 6
Connecting the Display To remove the Stand Base: 1. Separate the Stand Body by lifting it as pressing the arrow on the Stand Body while holding the Stand Base with the other hand. 2. The body of the Stand and the Stand Base are successfully separated. A5
Resumen del contenido incluido en la página 7
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5˚~20˚ 20 Warning: When adjusting the angle of the screen, do not put your finger(s) in between the head of the monitor and the stand body . You can hurt your finger(s). Ergonomic It is recommended that
Resumen del contenido incluido en la página 8
Connecting the Display Using the Computer 1. Place the monitor in a convenient, well-ventilated location near your computer. 2. Connect the signal cable. When attached, tighten the thumbscrews to secure the connection. 1 3. Connect the power cord into a proper power outlet that is easily accessible and close to the display. 2 Signal Cable Power Cord Varies according to model. NOTE Wall-outlet type This is a simplified representation of the rear view. This rear view represents a 2 general mo
Resumen del contenido incluido en la página 9
Control Panel Functions Rear Front Panel Controls Control Function Use this button to enter or exit the On Screen Display. MENU Button OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear. You can unlock the OSD controls at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" should appear. Use these
Resumen del contenido incluido en la página 10
Control Panel Functions Control Function Use this button to enter a selection in the On Screen AUTO/SET Display. Button AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press the AUTO/SET button before entering the On Screen Display(OSD). This will automatically adjust your display image to the ideal settings for the current screen resolution size (display mode). The best display mode is L192WS : 1440 x 900 Power Button Use this button to turn the display on or off. This Indic
Resumen del contenido incluido en la página 11
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making image adjustments. To make a
Resumen del contenido incluido en la página 12
On Screen Display(OSD) Selection and Adjustment The following table describes all the On Screen Display control, adjustment, and setting menus. Main menu Sub menu Reference To adjust the brightness, PICTURE BRIGHTNESS contrast and gamma of the CONTRAST screen GAMMA COLOR PRESET sRGB To customize the color of the screen 6500K 9300K RED GREEN BLUE HORIZONTAL POSITION To adjust the position of the VERTICAL screen CLOCK TRACKING To improve the clarity and PHASE s
Resumen del contenido incluido en la página 13
On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears. Menu Name PICTURE Sub-menus Icons Button Tip MENU : Exit : Adjust (Decrease/Increase) SET : Enter : Select another sub-menu NOTE OSD (On Screen Display) menu languages on the monitor
Resumen del contenido incluido en la página 14
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description PICTURE Adjusts the brightness of the screen. BRIGHTNESS PICTURE Adjusts the contrast of the screen. CONTRAST Set your own gamma value. : -50/0/50 GAMMA On the monitor, high gamma values display whitish images and low gamma values display high contrast images. MENU : Exit : Decrease : Increase SET : Select another sub-menu COLOR Selects the color temperature. PRESET • sRGB: Set the screen color to fit the COLOR SR
Resumen del contenido incluido en la página 15
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description POSITION POSITION Adjusts the screen image left and right. HORIZONTAL Adjusts the screen image up and down. VERTICAL MENU : Exit : Decrease : Increase SET : Select another sub-menu TRACKING TRACKING CLOCK Adjusts any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. PHASE Adjusts the focus of the display. This item allows you to remove any horizontal noise and cl
Resumen del contenido incluido en la página 16
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description LANGUAGE To choose the language in which the control names are displayed. SETUP OSD To adjust position of the OSD window POSITION on the screen. SETUP WHITE If the output of the video card is different BALANCE the required specifications, the color level may deteriorate due to video signal distortion. Using this function, the signal level is adjusted to fit into the standard output level of the video card in order to
Resumen del contenido incluido en la página 17
Troubleshooting Check the following before calling for service. No image appears No image appears Is the power cord of the • Check and see if the power cord is connected display connected? properly to the power outlet. Is the power indicator • Press the Power button. light on? • Adjust the brightness and the contrast. Is the power on and the power indicator blue or green? Is the power indicator • If the display is in power saving mode, try moving amber? the mouse or pressing any key on t
Resumen del contenido incluido en la página 18
Troubleshooting Display image is incorrect Display Position is • Press the AUTO/SET button to automatically incorrect. adjust your display image to the ideal setting. If the results are unsatisfactory, adjust the image position using the H position and V position icon in the on screen display. • Press the AUTO/SET button to automatically On the screen adjust your display image to the ideal setting. background, vertical If the results are unsatisfactory, decrease the bars or stripes are vert
Resumen del contenido incluido en la página 19
Troubleshooting Display image is incorrect The screen color is • Check if the signal cable is properly connected mono or abnormal. and use a screwdriver to fasten if necessary. • Make sure the video card is properly inserted in the slot. • Set the color setting higher than 24 bits (true color) at Control Panel - Settings. The screen blinks. • Check if the screen is set to interlace mode and if yes, change it to the recommend resolution. Have you installed the display driver? Have you insta
Resumen del contenido incluido en la página 20
Specifications Display 19 (48 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating 19 inches viewable 0.2835 mm pixel pitch Horizontal Freq. 30 - 83 kHz (Automatic) Sync Input Vertical Freq. 56 - 75 Hz (Automatic) Input Form Separate TTL SOG (Sync On Green) Signal Input 15 pin D-Sub Connector Video Input Input Form RGB Analog (0.7 Vp-p/ 75 ohm) Resolution Max VESA 1440 x 900 @75 Hz Recommend VESA 1440 x 900 @60 Hz Plug&Play
