Résumé du contenu de la page N° 1
This Manual is Bookmarked
Owner's Manual
®
XACTA Fence II Homeshop 30/52
WMH TOOL GROUP
2420 Vantage Drive
Elgin, Illinois 60123 Part No. M-708928Z
Ph.: 800-274-6848 Revision B 03/06
www.wmhtoolgroup.com Copyright © WMH Tool Group
Résumé du contenu de la page N° 2
WARRANTY AND SERVICE WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these WMH Tool Group Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or ® perform routine maintenance and major repair on your JET tools. For the name of an Authorized Service Center in your area call 1-800-2
Résumé du contenu de la page N° 3
Table of Contents WARRANTY AND SERVICE ........................................................................................................................2 Table of Contents..........................................................................................................................................3 Warnings .......................................................................................................................................................4 Unpacking ......
Résumé du contenu de la page N° 4
Warnings 1. Read and understand the entire owners manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace the warning labels if they become obscured or removed. 4. The Table Saw on which the XACTA Fence II is used is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper a
Résumé du contenu de la page N° 5
21. Keep visitors a safe distance from the work area. Keep children away. 22. Make your workshop child proof with padlocks, master switches or by removing starter keys. 23. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious injury. 24. Maintain a balanced stance at all times so that you do not fall into the blade or other moving parts. Do not overreach or use excessive force to perform any machine op
Résumé du contenu de la page N° 6
Unpacking Open shipping cartons and check that all parts are intact. Report any damage immediately to your distributor. Read the instruction manual thoroughly for assembly, alignment, and maintenance instructions. Contents of the Shipping Containers Box One: 1 XACTA Fence II 1 Lock Lever Knob Box Two: 1 Front Rail 1 Back Rail 1 Guide Tube 3 Black Plastic End Caps 1 Hardware Bag containing: 00014 ea 1/4-20 x 1-1/2 Hex Cap Screws 00007 ea 1/4-20 x 3/4
Résumé du contenu de la page N° 7
Installation Tools required Drill with 5/16" drill bit 10mm open end wrenches Cross point screwdriver Adjustable square Hammer (or rubber mallet) Straight edge The following instructions are for installing the XACTA Fence II and Rail System on JET Models JWCS-10 and JWTS-10 series table saws. Front Rail Installation Referring to Figures 1: 1. With a 5/16” drill bit, drill out the two threaded holes on the table front (C). Note: By drilling out the t
Résumé du contenu de la page N° 8
Back Rail Installation 1. Locate the back rail which is 1-1/2" x 1-1/2" with holes running along one side only. The height of the back rail when attached to the saw is not critical. 2. Align the holes in the back rail to the holes in the table top, as shown in Figure 4. 3. Secure the back rail to the holes in the saw table with four 1/4-20x 1-1/2 hex cap screws, eight 1/4 flat washers, four 1/4 lock washers, and four 1/4 hex nuts as shown in Figure 5. Tighten screws securely wit
Résumé du contenu de la page N° 9
3. Tap down the extension table at various points along its edge where it meets the saw table, until it is level with the saw table (Figure 7). As one part of the edge becomes level with the table, tighten the clamp on that side. Then move to the other side and repeat, until the full length of the edge is level with the saw table. Lay a straight edge across both extension table and saw table to ensure proper leveling. When extension table is properly aligned, holes Figure
Résumé du contenu de la page N° 10
Guide Tube Referring to Figure 11: The guide tube (A) is placed on top of the front rail (B) and is mounted with the scale facing toward the operator. 1. Align the holes in the bottom of the guide tube (A) with the holes in the front rail (B). 2. Fasten the guide tube (A) to the rail (B) from beneath with 1/4-20 x 3/4 hex cap screws (C), 1/4 lock washers (F) and 1/4 flat washers (G). Finger-tighten only. Figure 11 3. Measure from the guide tube to the table top in several place
Résumé du contenu de la page N° 11
A Fence Adjustments Fence Side Plate Note: Fence adjustments should be performed in Table Top the order given. C B Back Rail Guide Tube Front Rail Figure 14 Leveling Fence to the Saw Table 1. Place the fence on the table and lock it. 2. View the fence from the left side of the saw (Figure 14). Look for the space between the table and the fence bottom to be equal along the entire length of the fence (A, B, Fig. 14). If adjustment is necessary: 3. Unlock the fence. 4. Using a
Résumé du contenu de la page N° 12
90 ° to the Table Adjustment 1. Place the fence on the saw table and lock it. 2. Place a square (A, Fig. 17) on the table next to the fence. The fence should be 90 ° to the table. 3. If adjustment is necessary, unlock the fence, and turn one of the two nylon adjustment screws (B, Fig. 17) until the fence is 90 ° to the table. 4. Lock the fence and check the adjustment again. Cursor Adjustment 1. Disconnect the table saw from the power source. 2. Raise the saw
Résumé du contenu de la page N° 13
Parts Ordering Replacement Parts To order parts or reach our service department, call 1-800-274-6848 between 7:30 a.m. and 5:30 p.m. (CST), Monday through Friday. Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately. Parts for XACTA Fence II Homeshop 30/52 Fence Assembly Index No. Part No. Description Size Qty 1 ...............HF2-101 ...................Left Side Plate...........................................
Résumé du contenu de la page N° 14
Parts for XACTA Fence II Homeshop 30/52 Rail Assembly Index No. Part No. Description Size Qty 1 ...............HF2-201 ...................Front Fence Rail - Standard................................. .................................... 1 .................HF2-201A.................Front Fence Rail - Long Table ............................. .................................... 1 2 ...............TS-0050071 .............Hex Head Cap Screw (30" Table)........................ 1/4”-20 x 1-1/2” ....
Résumé du contenu de la page N° 15
Parts for the XACTA Fence II Homeshop 30/52 Leg Assembly Index No. Part No. Description Size Qty 1 ...............XF2-301 ...................Leg ....................................................................... .................................... 2 2 ...............TS-0561031 .............Hex Nut ................................................................ 3/8”-16......................... 2 3 ...............XF2-303 ...................Adjusting foot ................................
Résumé du contenu de la page N° 16
WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60123 Phone: 800-274-6848 www.wmhtoolgroup.com 16
