Résumé du contenu de la page N° 1
AC-2500E
High Pressure Washer
Operator’s Manual 1
Résumé du contenu de la page N° 2
Introduction THANK YOU for purchasing a John Deere product. The SERIAL NUMBER is located in the Specification or Identification Numbers section. Accurately record all the READ THIS MANUAL carefully to learn how to operate numbers to help in tracing the machine should it be stolen. and service your machine correctly. Failure to do so could Your dealer also needs these numbers when you order result in personal injury or equipment damage. This manual parts. File the identification numbers in a
Résumé du contenu de la page N° 3
Contents Page Safety ........................................................................ 5 Controls ................................................................. 13 Preparing the Washer ............................................ 14 Operating the Washer ............................................ 18 Troubleshooting ..................................................... 24 Storage .................................................................... 26 Specifications .....
Résumé du contenu de la page N° 4
Contents 4 Operator’s Manual
Résumé du contenu de la page N° 5
Safety RECOGNIZE SAFETY INFORMATION This is the safety alert symbol. When you see this symbol on your machine or in this manual, be alert to the potential for personal injury. Follow recommended precautions and safe operating practices. UNDERSTAND SIGNAL WORDS A signal word--DANGER, WARNING or CAUTION--is used with the safety-alert symbol. DANGER identifies the most serious hazards. DANGER or WARNING safety signs are located near specific hazards. General precautions are listed on CAUTI
Résumé du contenu de la page N° 6
PROTECT AGAINST HIGH PRESSURE SPRAY Spray from high pressure nozzles can penetrate the skin and cause serious injury. Keep spray from contacting hands or body. Never point the gun at yourself or anyone else. Never put your hand, fingers or body directly over the spray nozzle. Always keep operating area clear of all persons. Use extreme caution when operating near children. If an accident does occur and the spray appears to have penetrated the skin, SEEK EMERGENCY MEDICAL CARE. DO NOT
Résumé du contenu de la page N° 7
EXTENSION CORDS AC1000E-C AC1500E-C Extension cords are not recommended for use on this pressure Cable Length Wire Gauge Wire Gauge washer. If the use of an extension cord is unavoidable, it must Up to 50 Feet 14 AWG 12 AWG be plugged into a GFCI found in circuit boxes or protected receptacles. 50 to 100 Feet 12 AWG 10 AWG Use only 3-wire extension cords that have 3-prong grounding type plugs and 3-pole cord connectors that accept the plug from the washer. Use only extension cords that are
Résumé du contenu de la page N° 8
CLEANING DETERGENT PRECAUTIONS DO NOT use solvents or highly corrosive detergents or acid type cleaners with this pressure washer. Use only mild detergents. KNOW YOUR DETERGENTS! Be prepared to tell a physician exactly what you are using in the event of an emergency. Read the Material Safety Data Sheet (MSDS) provided with your detergent and all detergent labels. Follow all appropriate instructions regarding preparation use, safety and transportation. Keep ALL detergents out of the reac
Résumé du contenu de la page N° 9
IMPORTANT SAFETY INSTRUCTIONS WARNING: To reduce the risk of injury, read this operator’s manual completely. When using this product, the following basic precautions should always be followed: 1. Read all the instructions before using the product. 2. This product is equipped with a Ground Fault Circuit Interrupter (GFCI) in the power cord to reduce the risk of electrical shock. If replacement of the plug or cord is needed, use only identical replacement parts. 3. Follow the grounding ins
Résumé du contenu de la page N° 10
IMPORTANT SAFETY INSTRUCTIONS 13. NEVER ALLOW CHILDREN OR ADOLESCENTS TO OPERATE THIS UNIT! 14. Read and follow all handling, operations, maintenance and safety instructions listed in this manual and provide such information to ANYONE who will be operating this unit. 15. This pressure washer is provided with a Ground Fault Circuit Interrupter (GFCI) built into the plug or the power supply cord, Should replacement of the cord or plug become necessary, use only identical replacement parts t
Résumé du contenu de la page N° 11
WEAR PROTECTIVE CLOTHING Wear close fitting clothing and safety equipment appropriate to the job. Wear a suitable hearing protective device such as earmuffs or earplugs to protect against objectionable or uncomfortable loud noises. Operating equipment safely requires the full attention of the operator. Do not wear radio or music headphones while operating machine. PREPARE FOR EMERGENCIES Keep a first aid kit and fire extinguisher handy. Keep emergency numbers for doctors, ambulance service,
Résumé du contenu de la page N° 12
SAFETY SIGNS AD VER TENCIA W ARNING RIESGO DE INYECCION O LISION SEVERA RISK OF INJECTION OR SEVERE INJURY. 34-1253 Never put your hand, fingers or body directly Nunca coloque la mano, los dedos o el cuerpo over the spray nozzle. directamente sobre la boquilla de rocío. Location: Wand 34-1253-030801-ENG. 34-0631 34-1477 Location: Motor Housing Location: Frame Assembly W ARNING RISK OF ELECTROCUTION. DO NOT REMOVE THIS TAG. 34-1473 Location: Electrical Box 1. Connect only to a properly gr
Résumé du contenu de la page N° 13
Controls CONTROLS A -- Motor Overload D -- Pump G -- Detergent Strainer K -- Water Inlet B -- On/Off Switch E -- GFCI H -- Detergent Hose L -- Water Outlet C -- Motor F -- Power Cord I -- Adjustable Unloader M -- High Pressure Knob Discharge Hose J -- Adjustable Injector N -- Gun Assembly O -- Quick Connect Nozzle Operator’s Manual 13
Résumé du contenu de la page N° 14
Preparing the Washer SET-UP WARNING: RISK OF EXPLOSION! DO NOT OPERATE UNIT IN AN AREA WHERE FLAMMABLE GAS VAPORS MAY BE PRESENT. AN ELECTRIC SPARK MAY CAUSE AN EXPLOSION. RISK OF BURSTING! DO NOT STORE / OPERATE UNIT IN A FREEZING ENVIRONMENT 1. This unit should only be placed on a level surface to ensure proper lubrication for the water pump while operating. NEVER spray water directly on the unit! 2. Do not place unit in an area: a. where there is evidence of oil or ga
Résumé du contenu de la page N° 15
Preparing the Washer NOZZLE CONNECTION WARNING: RISK OF SEVERE INJURY! THE TRIGGER GUN SHOULD ALWAYS BE LOCKED IN THE OFF POSITION WHEN NOT IN USE! 1. Be certain the trigger gun is locked in the "OFF" position. 2. The nozzle assembly should be disconnected from the gun/wand assembly at this by retracting the locking ring on the quick-connect fitting to remove the nozzle. WATER SUPPLY 1. Select a water supply hose which is a quality grade of garden hose measuring at least 3/4"
Résumé du contenu de la page N° 16
Preparing the Washer POWER CORD CONNECTION WARNING: RISK OF ELECTROCUTION! THIS UNIT MUST BE CONNECTED TO A PROPERLY GROUNDED OUTLET. DO NOT USE AN ADAPTER OR REMOVE THE THIRD GROUNDING PRONG. TO REDUCE THE RISK OF ELECTROCUTION, KEEP ALL CONNECTIONS DRY AND OFF THE GROUND. DO NOT TOUCH PLUG WITH WET HANDS. 1. Make certain the motor switch is in the "OFF" position. 2. Ensure electrical supply is identical to the specifications listed on the pressure washer data plate. 3.
Résumé du contenu de la page N° 17
Preparing the Washer UNLOADER The unloader valve on your machine is equipped with an adjustment knob to adjust the pressure. Should less pressure be required, simply turn the adjustment knob counterclockwise. To set back to maximum, turn adjustment knob completely clockwise. DO NOT OVERTIGHTEN! CAUTION: RISK OF UNIT DAMAGE! DO NOT OVERTIGHTEN THE UNLOADER. BREAKAGE WILL RESULT IN IMMEDIATE LOSS OF WATER PRESSURE AND COSTLY REPAIRS. THERMAL RELIEF VALVE To ensure the bypass wa
Résumé du contenu de la page N° 18
Operating the Washer PRIMING THE PUMP 1. It is essential to prime the pump on initial start-up and each time the water supply is disconnected from the unit after initial use. 2. Lay the high pressure hose out to remove any loops. Water flow will constrict the hose, creating tight loops if the hose is not straight. 3. Securely connect the gun assembly to the high pressure hose. NOTE: The nozzle assembly should NOT be connected to the gun assembly at this time. See "Nozzle Connection" . 4.
Résumé du contenu de la page N° 19
Operating the Washer START-UP WARNING: RISK OF INJECTION CAUSING SEVERE INJURY! KEEP CLEAR OF NOZZLE! NEVER PLACE HAND OR FINGERS IN FRONT OF NOZZLE! DO NOT DIRECT DISCHARGE STREAM AT PEOPLE OR PETS! BE CERTAIN THE ADJUSTABLE NOZZLE ASSY. IS SECURELY CONNECTED TO THE WAND TO PREVENT AN ACCIDENTAL DISCHARGE! CAUTION: RISK OF DAMAGE. DO NOT ALLOW SPRAY PATTERN TO REMAIN ON A FIXED AREA FOR AN EXTENDED PERIOD OF TIME. POSSIBLE DAMAGE MAY OCCUR TO THE ARE
Résumé du contenu de la page N° 20
Operating the Washer CLEANING HORIZONTAL SURFACES Move nozzle wand from side to side. Direct spray at an angle to force debris ahead and away from the cleared area. Depending on the material to be removed and nozzle pressure, hold nozzle end 8 to 10 inches (20 to 25 cm) from the surface and use slow, overlapping strokes. If debris is easy to remove, move nozzle back to cover more area for faster cleaning. CLEANING VERTICAL SURFACES IMPORTANT: Remember that the washer can deliver a high
