Résumé du contenu de la page N° 1
User’s Guide
W3000H
Make sure to read the Important Precautions before using the product.
Keep the User's Guide(CD) in an accessible place for future reference.
See the label attached on the product and give the information to your
dealer when you ask for service.
Résumé du contenu de la page N° 2
Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national stan
Résumé du contenu de la page N° 3
Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation. If these openings are blocked, built-up heat can cause failures wh
Résumé du contenu de la page N° 4
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand base or Removing the stand base 1. Place the monitor with its front facing downward on a cushion or soft cloth. 2. Align the hooks on the Stand Body with the matching slots in the Stand Base. 3. Insert the hooks into slots. Hook Stand Body Stand Base Slot Warning The tape and locking pin may only be removed from those mon
Résumé du contenu de la page N° 5
Connecting the Display 4. Attach the monitor to the Stand Base by turning the screw to the right. Screw : Turn the screw by using the screw handle. 5. Lift and turn the monitor to face towards the front after the connection is made to the female part of the cable you're attaching. 6. Take the screw out by turning to the left to separate the monitor and Stand Base. Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture
Résumé du contenu de la page N° 6
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5˚~20˚ Swivel Range : 350˚ Height Range : maximum 3.94 inch (100.0mm) 100.0mm * Please be sure to remove the Locking pin to adjust the height. Ergonomic You do not need to
Résumé du contenu de la page N° 7
Connecting the Display Using the Computer 1. First, make sure that the power on the PC, monitor and peripheral equipment are off and then, connect as follows. 2. Connect DVI-D signal cable . 1 When attached, tighten the thumbscrews to secure the connection. 2 3. Insert the power cord into the outlet. Varies according to model. Signal Cable Power Cord 2 1 Wall-outlet type DVI-D signal cable PC 4. Touch the power button on the front of the monitor to turn on the monitor. Power button
Résumé du contenu de la page N° 8
Connecting the Display Connecting the USB(Universal Serial Bus) Cable "USB (Universal Serial Bus)" is an innovation in connecting your different desktop peripherals conveniently to your computer. By using the USB, you will be able to connect your mouse, keyboard, and other peripherals to your display instead of having to connect them to your computer. This will give you greater flexibility in setting up your system. USB allows you to connect a chain of up to 120 devices on a single USB port; an
Résumé du contenu de la page N° 9
Connecting the Display To arrange the cables Connect the power cord and the signal cable as shown in the figure and then fix them to the cable holders 1 and 2. 1. Please insert the cable holder1 2. Please put the power cord and into a hole. the signal cable in the cable holder 1. Cable Holder 1 3. Please put the power cord and the signal cable in the cable holder 2. While pressing the bottom of cable holder 2 with one hand, pull the top of it with the other hand as shown in the picture.
Résumé du contenu de la page N° 10
Control Panel Functions Front Panel Controls 4 5 Power Button Touching the button to turn the power on and touch the button again to turn it off. This Indicator lights up blue when the display Power Indicator operates normally(On Mode). If the display is in Sleep Mode (Energy Saving), this indicator color changes to amber. You can adjust monitor brightness to be lighter ( ) Buttons or darker ( ). When adjusting brightness, it will beep once when you reach the maximum or minimum level.
Résumé du contenu de la page N° 11
Troubleshooting Check the following before calling for service. No image appears No image appears Is the power cord of the • Check and see if the power cord is connected display connected? properly to the power outlet. Is the power on and the • Adjust the brightness and the contrast. power indicator blue or green? Is the power indicator • If the display is in power saving mode, try moving amber? the mouse or pressing any key on the keyboard to bring up the screen. • Try to turn on the PC.
Résumé du contenu de la page N° 12
Troubleshooting Display image is incorrect The screen color is • Check if the signal cable is properly connected mono or abnormal. and use a screwdriver to fasten if necessary. • Make sure the video card is properly inserted in the slot. • Set the color setting higher than 24 bits (true color) at Control Panel - Settings. The screen blinks. • Check if the screen is set to interlace mode and if yes, change it to the recommend resolution. Have you installed the display driver? Have you insta
Résumé du contenu de la page N° 13
Specifications Display 30 inches (75.6228cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating 30 inches viewable 0.2505 mm pixel pitch Horizontal Freq. 98.71kHz (Automatic) Sync Input Vertical Freq. 59.97 Hz (Automatic) Input Form Digital(HDCP) Video Input Signal Input DVI - D connector (Digital) Input Form Digital Max VESA 2560 x 1600 @ 60 Hz Resolution Recommend VESA 2560 x 1600 @ 60 Hz DDC 2B Plug&Play : 130W(Typ.),140W(USB Full load) Power On Mode Sleep Mode ≤ 2 W Consumption Of
Résumé du contenu de la page N° 14
Specifications Stand Base Attached ( ), Detached ( O ) Power cord Wall-outlet type or PC-outlet type Standard USB 2.0, Self-Power USB Data Rate Max 480 Mbps Power Consumption Max 2.5W x 4 NOTE Information in this document is subject to change without notice. A13
Résumé du contenu de la page N° 15
Specifications Preset Modes (Resolution) Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz) 1 1280 x 800 49.310 60 *2 2560 x 1600 98.713 60 *Recommend Mode Indicator MODE LED Color Blue On Mode Amber Sleep Mode Off Off Mode A14
Résumé du contenu de la page N° 16
Installing the Wall mount plate This monitor satisfies the specifications of the Wall mount plate or the interchange device. 1. After moving the product to face downward, make sure to place it on a soft cloth or a cushion to avoid surface damage. 2. Remove the screw by using a screwdriver, and pull the Stand part in the arrow direction. Then the Head and Stand parts are separated. 3. Install the Wall mount plate. Wall mount plate(Separate purchase) This is stand-type or wall mount type and i
Résumé du contenu de la page N° 17
Digitally yours
