Résumé du contenu de la page N° 1
TM
EZ Connect
802.11a Wireless Access Point
Protocol-independent networking functionality
54Mbps data rate per channel (up to 72 Mbps in turbo
mode): offers a high data rate and reliable wireless
connectivity with considerable cost savings over wired
LANs
Coverage area up to 1650 feet
Seamless connectivity to wired 10/100Mbps Ethernet
LANs augments existing networks quickly and easily
64/128/152-bit Wired Equivalent Privacy (WEP) support
Omni-directional antenna
Easy installati
Résumé du contenu de la page N° 2
Résumé du contenu de la page N° 3
TM EZ Connect User Guide From SMC’s EZ line of low-cost workgroup LAN solutions 6 Hughes December 2001 Irvine, CA 92618 Part No: 01-111320-006 Pub #: 150000013800AR01 Phone: (949) 707-2400
Résumé du contenu de la page N° 4
Copyright Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to change specifications at any time without notice. Copyright © 2001 by SMC Networks, Inc. 6 Hughes Irvine, CA 92618 All
Résumé du contenu de la page N° 5
LIMITED WARRANTY Limited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products to be free from defects in workmanship and materials, under normal use and service, for the applicable warranty term. All SMC products carry a standard 90-day limited warranty from the date of purchase from SMC or its Authorized Reseller. SMC may, at its own discretion, repair or replace any product not operating as warranted with a similar or functionally equivalent product, during the applicable
Résumé du contenu de la page N° 6
LIMITED WARRANTY WARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, CUSTOMER’S SOLE REMEDY SHALL BE REPAIR OR REPLACEMENT OF THE PRODUCT IN QUESTION, AT SMC’S OPTION. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. SMC NEITHER ASSUME
Résumé du contenu de la page N° 7
COMPLIANCES FCC - Class B FCC ID: HEDACCWA5001 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions, may cause harmful interference to radio communications. Howe
Résumé du contenu de la page N° 8
COMPLIANCES iv
Résumé du contenu de la page N° 9
EZ CONNECT™ 802.11A WIRELESS ACCESS POINT INTRODUCTION SMC’s EZ Connect 802.11a Wireless Access Point (SMC2755W) is an access point that provides transparent, wireless high speed data communications between the wired LAN (and/or within the wireless network) and fixed, portable or mobile devices equipped with a 802.11a wireless adapter (such as SMC2735W) employing the same radio modulation. This solution offers fast, reliable wireless connectivity with considerable cost savings over wired
Résumé du contenu de la page N° 10
EZ CONNECT™ 802.11A WIRELESS ACCESS POINT Please register this product and upgrade the product warranty at www.smc.com. Please inform your dealer if there are any incorrect, missing or damaged parts. If possible, retain the carton, including the original packing materials. Use them again to repack the product in case there is a need to return it. Hardware Description Ethernet Compatibility SMC’s Wireless Access Point can attach directly to 10BASE-T/ 100BASE-TX (twisted -pair) Ethernet LAN se
Résumé du contenu de la page N° 11
INTRODUCTION Applications The EZ Connect Wireless products offer a high speed, reliable, cost-effective solution for 10/100Mbps wireless Ethernet client access to the network in applications such as: • Remote access to corporate network information E-mail, file transfer and terminal emulation Difficult-to-wire environments Historical or old buildings, asbestos installations and open areas where wiring is difficult to employ Frequently changing environments Retailers, manufacturers and ba
Résumé du contenu de la page N° 12
EZ CONNECT™ 802.11A WIRELESS ACCESS POINT LED Indicators The Wireless Access Point includes three status LED indicators, as described in the following figure and table. Wireless Power Link/Activity Ethernet Link/Activity LED Status Description Power On Indicates the power is being supplied. Flashing Indicates - running a self-test loading software program system errors (refer to “Troubleshooting” on page 36 for details) Ethernet Link/Activity On Indicates a valid 100Mbps Ethernet cable
Résumé du contenu de la page N° 13
INTRODUCTION System Requirements Before you install the Wireless Access Point, be sure you can meet the following requirements: An A/C power outlet (100~240 V, 50~60 Hz) which will supply power for the Access Point An available RJ-45 (UTP) port on a 10/100Mbps Ethernet hub or switch 802.11a compliant wireless Ethernet adapters with TCP/IP compatible protocol installed Web browser for configuration 5
Résumé du contenu de la page N° 14
EZ CONNECT™ 802.11A WIRELESS ACCESS POINT HARDWARE INSTALLATION SMC2755W - Top Panel TM EZ Connect 802.11a Wireless Access Point SMC2755W 1. Select the Site – Choose a proper place for your SMC2755W Wireless Access Point. In general, the best location is at the center of your wireless coverage area, within line of sight to all wireless devices. 2. Placement of the Wireless Access Point – Proper placement will improve performance. Try to place the Access Point in a position that can best cov
Résumé du contenu de la page N° 15
SMC2755W - Rear Panel Reset Button 3.3V 4A MAX RJ-45 3.3 V DC Connector Power Socket 3. Connect the Ethernet Cable – The SMC2755W can be wired to a 10/100Mbps Ethernet through a network device such as a hub or a switch. Connect to the RJ-45 connector socket on the back panel with category 3, 4 or 5 UTP Ethernet cable and an RJ-45 connector. 4. Connect the Power Cable – Connect the power adapter cable to the 3.3 V DC power socket on the rear panel. Warning: USE ONLY the power adapter suppli
Résumé du contenu de la page N° 16
EZ CONNECT™ 802.11A WIRELESS ACCESS POINT SYSTEM CONFIGURATION The CD-ROM that comes with the package contains a utility program for the EZ Connect Wireless Access Point. Any updates can be downloaded from SMC’s Web site at: http://www.smc.com Note: Check the SMC website for more support options (See “Troubleshooting” on page 36). You can access the online support options at: http://www.smc.com/index.cfm?action=tech_support_support_tools The SMC2755W can be configured over an Ethernet netw
Résumé du contenu de la page N° 17
Windows Installation (98/2000/Me/NT/XP) 1. Insert the CD-ROM that comes with the package into the CD-ROM drive on your PC, and then enter the following command: “D:\utility\setup.” Follow the on-screen instructions to install the utility program. 2. After you finish the installed utility, choose “Programs,” then “SMC EZ Connect 802.11a,” and select “EZ Connect 802.11a Configuration Utility,” from the “Start” menu. 3. The program will then detect all the SMC2755W Wireless Access Point(s) o
Résumé du contenu de la page N° 18
EZ CONNECT™ 802.11A WIRELESS ACCESS POINT 5. The Web management window will appear. You can also manually launch a web browser from a PC and enter the IP address that is assigned to the SMC2755W. The SMC2755W 802.11a AP Web-based configuration page will be displayed. Setup Wizard 1. To access the Access Point’s management interface, enter the username “Admin” with a password “5up” and click “Login.” 2. The home page displays the Main Menu on the screen. 10
Résumé du contenu de la page N° 19
SYSTEM CONFIGURATION 3. Click on “Setup Wizard” to display basic configurations including SSID, Channel, Authentication Type and Standard WEP Setup. 4. Click on the “Next” button to start using the “1-2-3 Setup Wizard.” SSID – The Service Set ID. This should be set to the same value as other wireless devices in your network. (Default: ANY) Note: The SSID is upper/lower case sensitive and can consist of 11
Résumé du contenu de la page N° 20
EZ CONNECT™ 802.11A WIRELESS ACCESS POINT up to 32 alphanumeric characters. Channel – You can select “Enable” to have the Access Point operating in turbo mode with data rate up to 72 Mbps. (Default: Disable) Authentication Type – Click on the “Shared Key” radio button to start filtering the frames with the addresses defined 12
