Résumé du contenu de la page N° 1
MUSIC | AUDIO POST | VIDEO | FILM
artist
professional control surface
i
USER GUIDE
Document Revision: B
Résumé du contenu de la page N° 2
professional control surface In the interest of continued product development, Euphonix reserves the right to make improvements to this manual and the product it describes at any time, without notice or obligation. MC Mix, MC Control, MC Pro, System 5-MC, and EuCon are trademarks of Euphonix, Inc. ©2008 Euphonix, Inc. All rights reserved worldwide. No part of this publication may be reproduced, trans- mitted, transcribed, stored in a retrieval system, or translated into any language in any form
Résumé du contenu de la page N° 3
professional control surface Canada This Class B digital apparatus complies with Canadian ICES-003 Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada European Union Australia ABN 91 051 557 905 Japan iii Artist Series USER GUIDE
Résumé du contenu de la page N° 4
professional control surface IMPORTANT SAFETY INSTRUCTIONS The lighting flash with arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electrical shock to persons. The exclamation point within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions
Résumé du contenu de la page N° 5
professional control surface 13) Unplug this apparatus during lightning storms or when unused for long periods of time. 14) Refer all servicing to qualified service personnel. Servicing is required when the appa- ratus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15) WARNING – TO REDUCE THE RISK OF F
Résumé du contenu de la page N° 6
Résumé du contenu de la page N° 7
professional control surface Table of Contents List of Figures ........................................................................................................ xi Chapter 1: Introduction to the Artist ................................................................. 13 Chapter 2: Setup and Installation ..................................................................... 15 2.1 Setting Up the MC Control .......................................................... 15 2.1.1 Elevating the MC
Résumé du contenu de la page N° 8
professional control surface 4.5 Knobs ........................................................................................ 33 4.5.1 Knob Set Selection ........................................................ 33 4.5.2 Knob Functions.............................................................. 35 4.5.3 Knob Set Navigation Keys .............................................. 35 4.6 Soft Keys.................................................................................... 37 4.7 Jog Wheel an
Résumé du contenu de la page N° 9
professional control surface 6.4.2 Footswitch..................................................................... 54 6.4.3 MC Control Display ........................................................ 55 6.5 Assign........................................................................................ 56 6.5.1 Display application’s track numbers............................... 57 6.5.2 Lock to application ........................................................ 57 6.5.3 Clear All Assignments .....
Résumé du contenu de la page N° 10
Résumé du contenu de la page N° 11
professional control surface List of Figures 1-1 MC Control and MC Mix .................................................................................. 13 2-1 Foldout leg (left); riser bracket (right) ............................................................. 15 2-2 Removing side panels (left); removing riser brackets ...................................... 16 2-3 Removing screws from the bottom panel ........................................................ 17 2-4 Removing connecting part an
Résumé du contenu de la page N° 12
professional control surface 6-2 Surfaces tab ................................................................................................... 48 6-3 Workstations tab ............................................................................................ 50 6-4 General tab .................................................................................................... 52 6-5 Preferences tab ..............................................................................................
Résumé du contenu de la page N° 13
professional control surface Chapter 1: Introduction to the Artist The MC Control and MC Mix comprise the Artist desktop control surfaces. They use a 100 Mbs Ethernet EuCon connection to control audio/video applications run- ning on a workstation computer. EuCon is a high-speed communication proto- col and enables control of virtually every application feature. The MC Mix and MC Control can each run as standalone devices and up to four MC Mixes can be used, with or without an MC Control, to c
Résumé du contenu de la page N° 14
professional control surface Conventions Used in this User Guide The User Guide refers to all functions labeled on the MC Control surface and rear panel with all caps in bold type (i.e., NUDGE , PAN, SEL, SOLO). The Shift key is used in conjunction with other keys to access secondary functions labeled in blue above the primary function. Two Shift keys are located at the MC Control’s bottom-left and -right. To describe Shift functions simply, “press and hold the Shift key then press the NUDG
Résumé du contenu de la page N° 15
professional control surface Chapter 2: Setup and Installation Euphonix is dedicated to making your MC Control experience enjoyable and trou- ble-free so we will periodically update the following software and documentation: • EuControl: This software runs your MC Control and communicates to your audio/ video application. Always download the new version if prompted to do so when you launch EuControl. • MC Control User Guide (PDF): This is the complete user guide for your MC Control and the docu
Résumé du contenu de la page N° 16
professional control surface Two larger, detached riser brackets elevate and angle the unit more than the foldout legs. Use moderate force to snap them into the bottom panel as shown in Figure 2-1. To remove the riser brackets: 1. Slide the side panels off (Figure 2-2 left). Figure 2-2 Removing side panels (left); removing riser brackets 16 2. Press the tabs to release the riser brackets (Figure 2-2 right). 3. Lift the riser bracket out of the MC Control to remove 2.1.2 Physically Linking Arti
Résumé du contenu de la page N° 17
professional control surface To join an MC Control to an MC Mix: 1. On the MC Mix, use a #2 Phillips screwdriver to remove the two silver screws (Figure 2-3). The screws may be tight, so you may have to use some force. Figure 2-3 Removing screws from the bottom panel 2. Lift the black plastic connecting part and side panel up and out of the MC Mix (Figure 2-4). 17 Figure 2-4 Removing connecting part and side panel 3. On the MC Control, remove the side panel (see Figure 2-2 left) on the end w
Résumé du contenu de la page N° 18
professional control surface 2.2 Installation 1. If you downloaded the latest software from the web, double-click the installer. Otherwise, insert the installation CD into your Macintosh. NOTE: Be sure to eject the installation CD in your Mac if you downloaded the latest software from the web. 2. Follow the instructions to install the software. If prompted to download the most current version of EuControl, follow the onscreen instructions. EuControl will launch automatically and is running
Résumé du contenu de la page N° 19
Eucon professional control surface 6. Plug one end of the Ethernet crossover cable into the Ethernet jack (labeled with ) on the rear panel of the MC Control (Figure 2-8). Ethernet cable Figure 2-8 Ethernet cable and rear panel jack 7. Plug the other end of the Ethernet crossover cable into an open Ethernet jack on your computer, router, or Ethernet switch (Figure 2-9). An Ethernet router or switch is required to connect additional MC Mixes or to a local area network. Note that connecting di
Résumé du contenu de la page N° 20
professional control surface 9. Press and release the POWER switch on your MC Control. Look at the top-right of your screen and wait up to 60 seconds. A green icon in the menu bar indicates correct installation. If you did not see the green icon: •See My Surfaces on page 40 and add the MC Control manually. • Shut down the MC Control and the Mac and repeat steps 8 and 9. • If your Mac is pre-2002 and you are using an Ethernet router or switch, you need to purchase a normal straight-through
