ページ1に含まれる内容の要旨
OPERATOR'S MANUAL
FACSIMILE RECEIVER
MODEL
FAX-408
www.furuno.co.jp
ページ2に含まれる内容の要旨
*00016160811* *00016160811* **00016160811 00016160811**
ページ3に含まれる内容の要旨
IMPORTANT NOTICES General • The operator of this equipment must read and follow the descriptions in this manual. Wrong op- eration or maintenance can cancel the warranty or cause injury. • Do not copy any part of this manual without written permission from FURUNO. • If this manual is lost or worn, contact your dealer about replacement. • The contents of this manual and equipment specifications can change without notice. • The example screens (or illustrations) shown in this manual can be differ
ページ4に含まれる内容の要旨
SAFETY INSTRUCTIONS The user and installer must read the appropriate safety instructions before attempting to install or operate the equipment. Indicates a potentially hazardous situation which, if not avoided, WARNING could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, CAUTION may result in minor or moderate injury. Warning, Caution Prohibitive Action Mandatory Action Safety Instructions for the Operator WARNING WARNING Do not open t
ページ5に含まれる内容の要旨
WARNING LABEL A warning label is attached to the main unit. CAUTION Do not remove the label. If the label is missing or damaged, contact a FURUNO agent or Do not use commercial cleaners to dealer about replacement. clean the main unit. Commercial cleaners may remove paint WARNING and markings. Remove dust from the main To avoid electrical shock, do not remove cover. No user-serviceable unit with a soft cloth. For stubborn dirt, use parts inside. water-diluted mild detergent and a soft clo
ページ6に含まれる内容の要旨
TABLE OF CONTENTS FOREWORD...............................................................................................vi EQUIPMENT LIST .....................................................................................vii SYSTEM CONFIGURATION ....................................................................viii 1. OPERATION ..........................................................................................1 1.1 Control Description .................................................
ページ7に含まれる内容の要旨
3. INSTALLATION................................................................................... 21 3.1 Main Unit ....................................................................................................................21 3.2 Antenna......................................................................................................................22 3.2.1 General antenna connection ......................................................................... 22 3.2.2 Whip or wire ante
ページ8に含まれる内容の要旨
FOREWORD A Word to the Owner of the FAX-408 FURUNO Electric Company thanks you for purchasing the FURUNO FAX-408 Facsimile Receiv- er. We are confident you will discover why the FURUNO name has become synonymous with quality and reliability. For over 60 years FURUNO Electric Company has enjoyed an enviable reputation for quality and reliability throughout the world. This dedication to excellence is furthered by our extensive global network of agents and dealers. Your equipment is designed and
ページ9に含まれる内容の要旨
EQUIPMENT LIST Standard supply Name Type Code No. Qty Remarks Facsimile Receiver FAX-408 — 1 Installation Materials CP08-02101 000-163-087 1 set See the Packing Lists at the end of this manual. Accessories FP08-01000 000-163-088 1 set Spare Parts SP08-02301 000-163-082 1 set Optional supply Name Type Code No. Remarks Preamp Unit FAX-5 000-075-016 w/15 m cable FAX-5 000-075-049 w/1 m cable Whip Antenna 04S4176 000-153-122 2.6 m, for use with FAX-5 FAW-6R2 000-572-108 6 m FAW-6R2A 000-107-921 6 m
ページ10に含まれる内容の要旨
SYSTEM CONFIGURATION Choose one WIRE ANTENNA WHIP ANTENNA WHIP ANTENNA (2.6 m) (6 m) OR PREAMP UNIT FAX-5 MATCHING BOX ARD-1 External 12-24 VDC Receiver FACSIMILE RECEIVER FAX-408 : Standard supply : Optional suppply : Local supply viii
ページ11に含まれる内容の要旨
1. OPERATION 1.1 Control Description Control panel Paper cutter Paper compartment cover TIMER PRG FRQ 1 2 3 TUNE DIM CH 45 6 RCD POWER ON REV SPD 7 89 VOLUME SYNC FACSIMILE RECEIVER FAX-408 IOC RCD C 0 E OFF PAPER FEED Control description Control, Description indicator POWER ON Turns power on and off. OFF VOLUME Adjusts volume of Rx signal and key beep. SYNC Fine tunes the phasing signal. 1
ページ12に含まれる内容の要旨
1. OPERATION Control description (con’t from previous page) Control, Description indicator • Enables a setting mode (in combination with numeric key). Press the key fol- PRG lowed by appropriate numeric key to choose setting mode. 1- Chooses internal or external receiver. 2- Sets timer reception functions. 3- Sets sleep timer. 4- Adds or edit channels. 5- Sets date and time. 6- Sets ISB shift. 7- Adjusts LCD contrast. 9- Clears RAM. • Returns to top page in setting mode. • Changes from channel m
ページ13に含まれる内容の要旨
1. OPERATION 1.2 Turning the Power On/Off Press the POWER key to turn the power on or off. When the power is applied, the last-used channel appears. 1.3 Adjusting LCD Contrast 1. Press the PRG key. 2. Press the 7 key to show the contrast setting screen. SET CONTRAST by / KEY 3. Press or key to adjust the contrast, in 10 levels (0-9). The chosen level is indicated on the LCD. 4. Press the E key. 5. Press the C key to return to the standby display. 1.4 Adjusting LCD Brilliance and LED
ページ14に含まれる内容の要旨
1. OPERATION 1.5.2 Selection of desired frequency, fine adjustment of frequency Frequency may also be entered manually by pressing the FRQ key, and then entering frequency by using the numeric keys and the REV/ key (for entering decimal point). The available frequency range is 2000.0 - 24999.9 kHz. In the frequency display mode, use the or key to fine tune a frequency when in the frequency display mode, in resolution of 0.1 kHz. When properly tuned, the center TUNE LED (green) lights. If
ページ15に含まれる内容の要旨
1. OPERATION 1.7 Manual Receiving This section shows you to manually receive a facsimile broadcast. For example, you may want to receive a facsimile broadcast already in progress or receive from a facsimile station that does not use start and stop signals. 1. Press the CH key to show the channel display. C000 JMH 3622.5 S120 I576 2. Press the or key to choose channel desired. Note: Alternatively, you may enter the frequency of the broadcasting station by pressing the FRQ ke
ページ16に含まれる内容の要旨
1. OPERATION 3. Press the 4 key to choose STR (Store). STORE TIMER REG SET REG No. 0-F 4. Use the or key to choose timer program number and press the E key. For example, choose “1” and the display then looks something like the one below. R1 SET CHANNEL No. in 3 FIGURES 5. Enter a channel number and press the E key. R1 C000 SET DAY of THE WEEK by 6. Set the day of the week which to receive the program, using the or key. Choose the asterisk (*) to get a broad
ページ17に含まれる内容の要旨
1. OPERATION 1.8.3 Disabling timer operation when awaiting reception Timer programs may be deleted from the timer reception schedule as follows. 1. Press the PRG key, and the message shown below appears. TIMER RCV : OFF? PUSH E KEY 2. Press the E key. 1.8.4 Unlocking the keyboard during timer reception All keys except the PRG key are locked during recording to prevent accidental adjustment of the equipment. If you need to operate the keyboard when timer reception is active, do the followi
ページ18に含まれる内容の要旨
1. OPERATION 1.9 Processing Facsimile Images Speed, IOC, phasing, synchronization and image format may be adjusted during recording. 1.9.1 Speed and IOC Choose the correct speed and IOC, otherwise the image will be received as shown in the illustra- tion below. Wrong Speed or IOC and Image Wrong speed: "60" chosen instead of "120" Two images are displayed. Wrong speed: "120" chosen instead of "60" Overlapped image appears. Wrong IOC The image will be extended (or foreshortened) when "288" (or 57
ページ19に含まれる内容の要旨
1. OPERATION IOC IOC is an acronym meaning Index of Cooperation, and it is the line density standard assigned by WMO: IOC 576, high density, IOC 288, low density. To choose IOC, do the following: 1. Press the IOC key to show the IOC display. IOC: 576 1-576 2-288 2. Press the 1 or 2 key to choose appropriate IOC. 1.9.2 Manual phasing When the FAX-408 starts recording a broadcast already in progress, or noise prevents detection of the phasing signal, a dead sector (black or white stripe) m
ページ20に含まれる内容の要旨
1. OPERATION 1.10 Sleep Timer The sleep timer feature sleeps the set after reception has passed. Fax signal will not be received when the sleep timer is active. 1.10.1 Activating the sleep timer 1. Press the PRG key. 2. Press the 3 key to show the sleep mode setting mode. SLEEP MODE : OFF 1-OFF 2-ON 3. Press the 1 key to disable the sleep timer or the 2 key to enable it. 4. If the 1 key was pressed at step 3, press the E key to turn off the sleep mode. If the 2 key was pressed, t
