ページ1に含まれる内容の要旨 
                    
                        LTC9316/00P
Security Systems
Installation Manual
Standard Pole
EN                                                                                                                                                                                                                                                                                                                                                                                                                                                   
                    
                    ページ2に含まれる内容の要旨 
                    
                        LTC9316/00P Instruction Manual Introduction EN 2 Table of Contents 1    DESCRIPTION 2 2    UNPACKING 2 3    SERVICE 2 4    4    INSTALLATION 3       4.1 Site Preparation 3       4.2. Installation 3       4.3  Mounting the AutoDome™ 4 4  INSTALLATION 1  DESCRIPTION This installation should be made by qualifi ed service personnel and  The LTC 9316/00P units are 16 foot steel mounting poles for  conform to the National Electrical Code and applicable local codes. use with Unity® Domes, AutoDomes®, an
                    
                    ページ3に含まれる内容の要旨 
                    
                        LTC9316/00P Instruction Manual Installation 3 EN 7.778 24" 6" 4X O 1.000 BASED ON A 11.00" B.C. 6" 36" 13.0007.778 4.000 32" 24" 24" O 11.000 4.000 O 3.000 13.000 24" 32" Figure 3 Anchor Bolt Dimensions 36" PV4 Anchor jig (if applicable) NOTE: Prepare the concrete per manufacturer's   directions. The concrete must have a compressive  ! 8" 8" strength of 3000 psi, and must be fabricated following  ACI318-89 requirements.  Allow the concrete  foundation to cure thoroughly before proceeding with  1
                    
                    ページ4に含まれる内容の要旨 
                    
                        LTC9316/00P Instruction Manual Installation 4 EN Access opening plates Bolts or  anchor jig Figure 7 Lifting the Pole into Position CAUTION:  Pull all slack in the wiring as you lift the pole into  position to keep from pinching and possible damage. Pad Figure 5 Placement of Pole on Pad   6.     Ensure that the pole is vertical on all sides.  Use a                    bubble level or plumb bob to check.     3.     Insert the wiring into the 3" diameter hole in the base of the            pole. Be 
                    
                    ページ5に含まれる内容の要旨 
                    
                        Mount the LTC 9540/xx  Wall Bracket Using  Adapter Plate These Holes Figure 9  Aligning Adapter Plate with Mounting Plate Figure 11  Mounting the LTC 9540/xx Wall Bracket 5 SPARE PARTS 2. Attach the LTC 9540/xx Wall Bracket adapter plate, using the provided hex head nuts and bolts, flat washers, and Part No. Description lockwashers (see Figure 10). LTC9316AP        LTC 9540/xx Wall Arm  Adapter Plate Lockwashers Flat Washers 5/16-18 Nuts Figure 10  Attaching the Adapter Plate 3. Attach the LTC 9
                    
                    ページ6に含まれる内容の要旨 
                    
                        Bosch Security Systems, Inc. Robert Bosch GmbH Bosch Security Systems B.V. 850 Greenfield Road Geschäftsbereich P.O. Box 80002 Lancaster, PA  17601 EE.UU. Postfach 10 60 50 5600 JB Eindhoven Tel: 800-326-3270  70049 Stuttgart The Netherlands Fax: 1-717-735-6560 Telefax (0711) 811-12 34 Tele +31 40 27 80000 www.boschsecuritysystems.com © 2005 Bosch Security Systems GmbH 3935 890 38012 28 June Data subject to change without notice.