ページ1に含まれる内容の要旨
Operating Instructions
For Color Video Monitor
TCM-0902 / TCM-1001
TCM-1002S / TCM-1402S
TCM-1501 / TCM-1701
TCM-1901 / TCM-2102S
TATUNG Company Of America
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
Table of Contents 1. FCC Information - 2 2. Safety Precautions - 2 3. General Features - 4 4. TCM-0902 Monitor Front and Rear Views - 5 5. TCM-1001 HI-RES. Monitor Front and Rear Views - 6 6. TCM-1002S Monitor Front and Rear Views - 7 7. TCM-1402S Monitor Front and Rear Views - 8 8. TSCM-1501 HI-RES. Monitor Front and Rear Views - 9 9. TCM-1701 HI-RES. Monitor Front and Rear Views - 10 10. TCM-1901 HI-RES. Monitor Front and Rear Views - 11 11. TCM-2
ページ4に含まれる内容の要旨
FCC INFORMATION This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no g
ページ5に含まれる内容の要旨
7. Route power cords so that they cannot be walked upon or tripped over. Do not allow anything to rest on the power cord. 8. Do not install monitor in wet areas, or where it may be exposed to rain or water. Do not spill liquid of any kind on the unit. 9. Unplug the power cord from the unit before cleaning the display. Use only a damp cloth. Do not use alcohol, spirits, or ammonia to clean the display. DO NOT ATTEMPT TO CLEAN THE INTERIOR OF THIS UNIT- THIS ACTION MUST BE PERFORMED BY
ページ6に含まれる内容の要旨
GENERAL FEATURES 1. Compatible With : NTSC / PAL System 2. Scanning System : NTSC, 525 Lines, 60 Hz or PAL, 625 Lines, 50 Hz 3. Video Input Signal : CVBS1 / CVBS2 / S-Y/C 4. Audio Input Signal : AU1 / AU2 5. Input Power : 100~240V AC 6. Limited twelve months warranty STANDARD SYSTEM COMPONENTS AND ATTACHMENTS The various components and attachments are shown below: TCM-0902 TCM-1001 TCM-1002S TCM-1402S TCM-1501 TCM-1701 TCM-1901 TCM-2102S 4
ページ7に含まれる内容の要旨
TCM-0902 MONITOR FRONT AND REAR VIEW Front View 1. Power On/Off Switch 2. Power-On Indicator 3. Contrast Adjustment 4. Brightness Adjustment 5. Tint Adjustment 6. Color Adjustment 7. Sharpness Adjustment 8. Volume Adjustment 9. CVBS1 / CVBS2 / S-Y/C Select Switch TCM-0902 Rear View 1. Power Inlet 2. Video 1 Input : BNC Connector 3. Video 1 Output : BNC Connector 4. Video 2 Input : BNC Connector 5. Video 2 Output : BNC Connector 6. Audio 1 Input : RCA Jack
ページ8に含まれる内容の要旨
TCM-1001 MONITOR FRONT AND REAR VIEW Front View 1. Power On/Off Switch 2. Power-On Indicator 3. Contrast Adjustment 4. Brightness Adjustment 5. Tint Adjustment 6. Color Adjustment 7. Sharpness Adjustment 8. Volume Adjustment 9. CVBS / S-Y/C Select Switch TCM-1001 Rear View 1. Power Inlet 2. Video 1 / Video 2 Select Switch 3. Video Load Impedance Switch 4. Video 1 Input : BNC Connector 5. Video 1 Output : BNC Connector 6. Video 2 Input : BNC Connector 7. V
ページ9に含まれる内容の要旨
TCM-1002S MONITOR FRONT AND REAR VIEW Front View 1. Power On/Off Switch 2. Power-On Indicator 3. Contrast Adjustment 4. Brightness Adjustment 5. Tint Adjustment 6. Color Adjustment 7. Sharpness Adjustment 8. Volume Adjustment 9. CVBS1 / S-Y/C Select Switch TCM-1002S Rear View 1. Power Inlet 2. Video Load Impedance Switch 3. Video 1 Input : BNC Connector 4. Video 1 Output : BNC Connector 5. Audio 1 Input : RCA Jack 6. Audio 1 Output : RCA Jack 7. S-Y/C Loa
ページ10に含まれる内容の要旨
TCM-1402S MONITOR FRONT AND REAR VIEW Front View 1. Power On/Off Switch 2. Power-On Indicator 3. Contrast Adjustment 4. Brightness Adjustment 5. Tint Adjustment 6. Color Adjustment 7. Sharpness Adjustment 8. Volume Adjustment 9. CVBS1 / S-Y/C Select Switch TCM-1402S Rear View 1. Power Inlet 2. Video Load Impedance Switch 3. Video 1 Input : BNC Connector 4. Video 1 Output : BNC Connector 5. Audio 1 Input : RCA Jack 6. Audio 1 Output : RCA Jack 7. S-Y/C L
ページ11に含まれる内容の要旨
TCM-1501 MONITOR FRONT AND REAR VIEW Front View 1. Power On/Off Switch 2. Power-On Indicator 3. Contrast Adjustment 4. Brightness Adjustment 5. Tint Adjustment 6. Color Adjustment 7. Sharpness Adjustment 8. Volume Adjustment 9. CVBS1 / CVBS2 / S-Y/C Select Switch 10. Audio 1 / Audio 2 Select Switch TCM-1501 Rear View 1. Power Inlet 2. Video 1 Load Impedance Switch 3. Video 2 Load Impedance Switch 4. Video 1 Input : BNC Connector 5. Video 1 Output : BNC Connec
ページ12に含まれる内容の要旨
TCM-1701 MONITOR FRONT AND REAR VIEW Front View 1. Power On/Off Switch 2. Power-On Indicator 3. Contrast Adjustment 4. Brightness Adjustment 5. Tint Adjustment 6. Color Adjustment 7. Sharpness Adjustment 8. Volume Adjustment 9. CVBS1 / CVBS2 / S-Y/C Select Switch 10. Audio 1 / Audio 2 Select Switch TCM-1701 Rear View 1. Power Inlet 2. Video 1 Load Impedance Switch 3. Video 2 Load Impedance Switch 4. Video 1 Input : BNC Connector 5. Video 1 Output : BNC Connec
ページ13に含まれる内容の要旨
TCM-1901 MONITOR FRONT AND REAR VIEW Front View 1. Power On/Off Switch 2. Power-On Indicator 3. Contrast Adjustment 4. Brightness Adjustment 5. Tint Adjustment 6. Color Adjustment 7. Sharpness Adjustment 8. Volume Adjustment 9. CVBS1 / CVBS2 / S-Y/C Select Switch 10. Audio 1 / Audio 2 Select Switch TCM-1901 Rear View 1. Power Inlet 2. Video 1 Load Impedance Switch 3. Video 2 Load Impedance Switch 4. Video 1 Input : BNC Connector 5. Video 1 Output : BNC Connect
ページ14に含まれる内容の要旨
TCM-2102S MONITOR FRONT AND REAR VIEW Front View 1. Power On/Off Switch 2. Power-On Indicator 3. Contrast Adjustment 4. Brightness Adjustment 5. Tint Adjustment 6. Color Adjustment 7. Sharpness Adjustment 8. Volume Adjustment 9. CVBS1 / CVBS2 / S-Y/C Select Switch 10. Audio1 / Audio2 Select Switch 11. Underscan Select Switch 12. 16:9 Select Switch TCM-2102S Rear View 1. Power Inlet 2. Video 1 Load Impedance Switch 3. Video 2 Load Impedance Switch 4. Video 1 I
ページ15に含まれる内容の要旨
OPERATION Operating Instructions 1. Place the monitor on a flat and firm surface (see Safety Precautions on page 2). 2. This monitor can be operated between 100VAC to 240VAC. 3. Plug the power cord into AC outlet on the wall. 4. Link the A / V terminal from your devices into the audio / video in RCA/BNC connectors of the monitor. 5. Turn your device system power switch ON. then turn the monitor power switch ON. The power indicator will be ON at this moment. 6. Allow about 30 seconds
ページ16に含まれる内容の要旨
MAINTENANCE If the quality of the picture is poor and cannot be improved by making adjustments on the front control panel, inspect all system connections and cable runs. To reduce the risk of electrical shock, do not remove the cover or back of monitor. No user- serviceable parts are inside. Refer servicing to qualified personnel, or contact the Tatung Customer Service Department for assistance. Refer to the Warranty and Return Information section. SPECIFICATIONS MODEL TCM-0
ページ17に含まれる内容の要旨
MODEL TCM-1001 TCM-1501 TCM-1701 TCM-1901 ELECTRICAL Input Voltage 100~240V AC, 60 / 50HZ , full range Power 50W 70W 72W 78W Consumption Horizontal 700 lines, Y/C 700 lines, Y/C 700 lines, Y/C 700 lines, Y/C Resolution more than 800 more than 800 more than 800 more than 800 lines lines lines lines Sweep Linearity 10 ﹪ GENERAL Input / Output Video / S-Video 2 BNC inputs, 2 BNC inputs, 2 BNC inputs, 2 BNC inputs, 75ohms, or Hi-Z 75ohms, or Hi-Z 75ohms, or Hi-Z 75ohms,
ページ18に含まれる内容の要旨
RACK MOUNT KIT TRD-294 TRD-294 can hold two 9” CRT monitors side by side mounting on the rack, monitor model: TCM-0902, TBM-0903. The installation procedure is simple: 1. Unscrew 4 rubber-foot from bottom of each monitor. 2. Secure monitors with TRD-294 bracket (FIG. 1) by using the screws and adapter bars provided in the package. 3. Secure the brackets directly to the rack frame, see FIG. 2 below. Warning: At least two persons are necessary to place the monitor mounting the rack
ページ19に含まれる内容の要旨
RACK MOUNT KIT TRK-141 TRK-141 used for rack mount of 14” or 15” CRT color monitors, model: TCM1402S and TCM-1501. The installation procedure is simple: 1. Unscrew two Screw (M5 x 10mm) on each side of the monitor. 2. Secure TRK-141 bracket to both side of the monitor with the screw provided in the package. (FIG. 1) 3. Secure the brackets directly to the rack frame, see FIG. 2 below. Warning: At least two persons are necessary to place the monitor mounting the rack. Notes: 1. S
ページ20に含まれる内容の要旨
RACK MOUNT KIT TRK-171, TRK-191 TRK-171 used for mount 17” CRT color monitor TCM-1701 on the rack. TRK-191 for 19” monitor, model: TCM-1901, VT19726DVR. The installation procedure is simple: 1. Unscrew three Screws (M6) on each side of the monitor. 2. Secure mounting brackets to both side of the monitor with original screws. (FIG 1) 3. Secure the brackets directly to the rack frame, see FIG. 2 below. Warning: At least two persons are necessary to mount the monitor on the rack.
