ページ1に含まれる内容の要旨
OPERATOR’S MANUAL
MODEL GC-STT-CS
THIS MANUAL CONTAINS THE OPERATING
INSTRUCTIONS AND SAFETY INFORMA-
TION FOR YOUR SCAG ACCESSORY. READ-
ING THIS MANUAL WILL PROVIDE YOU
WITH MAINTENANCE AND ADJUSTMENT
PROCEDURES TO KEEP YOUR ACCESSORY
PERFORMING TO MAXIMUM EFFICIENCY.
THE SPECIFIC MODELS THAT THIS BOOK
COVERS ARE CONTAINED ON THE INSIDE
COVER. BEFORE OPERATING YOUR MA-
CHINE, PLEASE READ ALL THE INFORMA-
TION ENCLOSED.
PART NUMBER 03140
ページ2に含まれる内容の要旨
WARNING FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY. * Keep all safety shields in place. * Before performing any maintenance or service, stop the machine and remove the spark plug wire. * If a mechanism becomes clogged, stop the engine and wait for all moving parts to come to a complete halt before cleaning. * Keep hands, feet and clothing away from power-driven parts. * Read this manual completely as well as the Operator's Manual that came with your
ページ3に含まれる内容の要旨
2.1 SAFETY AND OPERATING 1.1 INTRODUCTION INSTRUCTIONS This manual has been prepared to provide the -NOTE- information you need to correctly assemble, operate, To avoid personal injury, it is imperative that all and maintain this grass catcher. Read it carefully and safety instructions be observed. keep it for future reference. 1. Read this operator's manual and the The replacement of any part on this product by other operator's manual that is supplied with the than the manufacturer's auth
ページ4に含まれる内容の要旨
5. To clean the hopper debris screen; 3. When dumping the hopper into a disposal area: A. Disengage the deck drive and allow all WARNING WARNING moving parts to come to a complete stop. DO NOT DUMP CLIPPINGS IN A DISPOSAL AREA THAT IS BURNING B. Apply parking brake and shut off the engine. A. Disengage the deck drive, apply the parking C. Stand on the left side of the hopper brake and allow all moving parts to come to assembly. a complete stop. D. Unhook the debris screen latches and B. Pul
ページ5に含まれる内容の要旨
3.1 ASSEMBLY INSTRUCTIONS FOR 52" 3. When installing this grass catcher on a machine CUTTER DECKS with a serial number below 8619999, you will need to remove the discharge baffle from the bottom of the cutter deck. See Figure 3-2. -NOTE- Replace the discharge baffle with the new baffle Use the illustrated parts list as a part provided with this grass catcher. Secure using number reference when following the the following hardware: assembly instructions. (1) 04001-12 Hex Head Bolt 5/16-18 x
ページ6に含まれる内容の要旨
LIFT LINK BELL CRANK SPACER NUT BOLT, 3/8-16 x 1-1/4" BOLT, 3/8-16 x 1-1/2" WASHER SPACER NUT CUTTER DECK REAR OF CUTTER DECK FRONT OF DISCHARGE CHUTE OPENING CUTTER DECK VIEW FROM RIGHT SIDE Figure 2-52"GC-STT install art OF CUTTER DECK FIGURE 3-3 BLOWER ELASTIC ASSEMBLY STOP NUTS HAIR PIN LOCK MOUNTING WASHERS POST PIN P R O P E R Y L CATCH S E C R E V I PLATE HEX HEAD E N N G E I BOLT W T H I O L I ELASTIC A N D STOP NUTS CARRIAGE F U E L . AND LOCK BOLTS WASHERS HEX HEAD
ページ7に含まれる内容の要旨
6. Install the blower mounting bracket to the deck 13. Install the plastic belt cover and secure with the using 1/2-13 x 1-1/2" hex head bolts (p/n 04001- plastic wing nuts. See Page 20 of the Illustrated 71), 1/2" spring lockwashers (p/n 04030-06), and Parts List for proper installation. 1/2-13 elastic stop nuts (p/n 04021-07). See Figure 3-3, Page 3. Do not fully tighten the 14. Install the hopper mounting brackets (p/n 451512 hardware at this time. & p/n 451595) to the outside of the frame o
ページ8に含まれる内容の要旨
18. Install the weight support bar to the front of the machine by resting it directly on top of the caster support arms and sliding it tight against the frame of the machine. Secure the weight bar to the machine using (2) bar clamps, (4) 3/8-16 x 1-1/2" bolts and (4) 3/8-16 elastic stop nuts. See Figure 3-6. 19. Install the weight assemblies to the weight support bar and secure them to the bar using the 1/2"x 6-1/4" pin and lanyard. See Figure 3-6 WEIGHT (5x) LANYARD ELASTIC STOP PIN NUT BAR
ページ9に含まれる内容の要旨
3. When installing this grass catcher on a machine 4.1 ASSEMBLY INSTRUCTIONS FOR 61" with a serial number below 8619999, you will CUTTER DECKS need to remove the discharge baffle from the bottom of the cutter deck. See Figure 3-2. -NOTE- Replace the discharge baffle with the new baffle Use the illustrated parts list as a part provided with this grass catcher. Secure using number reference when following the the following hardware: assembly instructions. (1) 04001-12 Hex Head Bolt 5/16-18
ページ10に含まれる内容の要旨
REAR OF CUTTER DECK FRONT OF DISCHARGE CHUTE OPENING CUTTER DECK VIEW FROM RIGHT SIDE OF CUTTER DECK Figure 2-61"GC-STT install art FIGURE 4-3 BLOWER ELASTIC ASSEMBLY STOP NUTS HAIR PIN MOUNTING LOCK POST WASHERS PIN ELASTIC STOP NUTS P R O P E R Y L AND LOCK CATCH WASHERS S E C R E V I PLATE E N N G E I W T H I O L I A N D CARRIAGE F U E L . BOLTS HEX HEAD BOLTS RIGHT SIDE OF CUTTER DECK SHOWN (Note: Some parts not shown for viewing purposes.) GC-STT install art 3 FIGURE 4-4
ページ11に含まれる内容の要旨
6. Install the blower mounting bracket to the deck 12. Install the hopper mounting brackets (p/n 451512 using 1/2-13 x 1-1/2" hex head bolts (p/n 04001- & p/n 451595) to the outside of the frame on the 71), 1/2" spring lockwashers (p/n 04030-06), and rear of the machine using 3/8-16 x 1" hex head 1/2-13 elastic stop nuts (p/n 04021-07). See bolts (p/n 04001-19) and 3/8-16 elastic stop nuts Figure 4-3, Page 8. Do not fully tighten the (p/n 04021-09). See Figure 5-6, Page 15. hardware at this tim
ページ12に含まれる内容の要旨
16. Install the weight support bar to the front of the machine by resting it directly on top of the caster support arms and sliding it tight against the frame of the machine. Secure the weight bar to the machine using (2) bar clamps, (4) 3/8-16 x 1-1/2" bolts and (4) 3/8-16 elastic stop nuts. See Figure 4-6. 17. Install the weight assemblies to the weight support bar and secure them to the bar using the 1/2"x 6-1/4" pin and lanyard. See Figure 4-6. WEIGHT (5x) LANYARD ELASTIC STOP PIN NUT BAR
ページ13に含まれる内容の要旨
3. When installing this grass catcher on a machine 5.1 ASSEMBLY INSTRUCTIONS FOR 72" with a serial number below 8619999, you will CUTTER DECKS need to remove the discharge baffle from the bottom of the cutter deck. See Figure 5-2. -NOTE- Replace the discharge baffle with the new baffle Use the illustrated parts list as a part provided with this grass catcher. Secure using number reference when following the the following hardware: assembly instructions. 1. Remove all packaging materials.
ページ14に含まれる内容の要旨
BLOWER ELASTIC ASSEMBLY STOP NUTS HAIR PIN MOUNTING LOCK POST WASHERS ELASTIC PIN STOP NUTS AND LOCK WASHERS CATCH PLATE CARRIAGE BOLTS HEX HEAD BOLTS RIGHT SIDE OF CUTTER DECK SHOWN (Note: Some parts not shown for viewing purposes.) GC-STT install art 3 FIGURE 5-3 P R O P E R Y L S E C R E V I E N N G E I W T H I O L I A N D F U E L . 12
ページ15に含まれる内容の要旨
6. Install the blower mounting bracket to the deck 12. Install the plastic belt cover and secure with the using 1/2-13 x 1-1/2" hex head bolts (p/n 04001- plastic wing nuts. See Page 20 of the Illustrated 71), 1/2" spring lockwashers (p/n 04030-06), and Parts List for proper installation. 1/2-13 elastic stop nuts (p/n 04021-07). See Figure 5-3, Page 12. Do not fully tighten the 13. Install the hopper mounting brackets (p/n 451512 hardware at this time. & p/n 451595) to the outside of the frame
ページ16に含まれる内容の要旨
17. Install the weight support bar to the front of the machine by resting it directly on top of the caster support arms and sliding it tight against the frame of the machine. Secure the weight bar to the machine using (2) bar clamps, (4) 3/8-16 x 1-1/2" bolts and (4) 3/8-16 elastic stop nuts. See Figure 4-6. 18. Install the weight assemblies to the weight support bar and secure them to the bar using the 1/2"x 6-1/4" pin and lanyard. See Figure 5-5 WEIGHT (5x) LANYARD ELASTIC STOP PIN NUT BAR CL
ページ17に含まれる内容の要旨
Item # Part # Description 1 04001-19 Bolt, Hex Head 3/8-16 x 1" 2 04021-09 Nut, Elastic Stop 3/8-16 3 04066-03 Quick Pin 4 423670 Spacer, Hitch 5 451512 Hitch Bracket Weldment 451595 Hitch Bracket Weldment, Floating Hopper Assembly 5 1 2 3 Liquid Cooled 2 Only 1 4 1 Note: 2 Illustration is for reference only. Some parts have been Frame 3 removed for visual purposes and may vary depending 5 on model. FIGURE 5-6 15
ページ18に含まれる内容の要旨
6.1 GRASS CATCHER REMOVAL INSTRUCTIONS 1. Prepare the work area making sure that it is a REMOVE clean, safe environment. 2. Remove the rubber strap holding the adapter to the blower assembly. See Figure 5-1. 3. Remove the belt from the spindle pulley. 4. Remove the pin holding the blower assembly to the mounting bracket on the cutter deck and REMOVE remove the blower assembly. See Figure 5-1. ADAPTER FIGURE 5-2 6. With the help of an assistant, remove the hopper BLOWER MOUNTING ASSEMBL
ページ19に含まれる内容の要旨
Notes 17
ページ20に含まれる内容の要旨
WARNING INSTALL BELT COVER BEFORE OPERATING MACHINE READ OPERATOR'S MANUAL DANGER ROTATING BLADES AND BLOWER Stop engine before cleaning or removing DO NOT OPERATE MOWER UNLESS GRASS CATCHER OR DISCHARGE GUARD IS INSTALLED GC-STT BLOWER HOUSING ASSEMBLY 9 48 10 11 12 13 2 4 8 1 9 5 3 11 7 6 10 10 14 44 47 27 14 12 11 15 43 16 42 14 15 26 17 41 39 40 18 34 27 19 17 20 28 21 41 25 38 22 3 35 27 23 36 24 46 29 14 24 14 30 33 32 37 31 31 45 34 47 36 390STT0200A 45 35 49 18
