ページ1に含まれる内容の要旨
D-Link DI-804V
Broadband VPN Router
Manual
Rev. 031902
Building Networks for People
ページ2に含まれる内容の要旨
Contents Package Contents .................................................... 3 Introduction............................................................... 4 IP Address Settings and Computer Settings ............ 8 Using the Configuration Utility .................................. 9 Basic Setup ............................................................ 10 Device Information.................................................. 18 Device Status ..........................................
ページ3に含まれる内容の要旨
Package Contents Contents of Package: • D-Link DI-804V Broadband VPN Router • Manual • Quick Installation Guide • Power Adapter - 5V DC, 2A* *Using a power supply with a different voltage rating will damage and void the warranty for this product. If any of the above items are missing, please contact your reseller System Requirements: Internet Explorer 4.0 or higher or Netscape Navigator 4.0 or higher, with JavaScript enabled One computer with an installed 10Mbps, 100Mbps o
ページ4に含まれる内容の要旨
Introduction The D-Link DI-804V Broadband VPN Router enables your network to connect to the Internet via a secure, private connection using a Cable/DSL modem, such as the D-Link DCM-200 Cable Modem. The Virtual Private Network that is created on the Internet between your home and your office (with a VPN server) is secure from interference when you use the DI-804V. It is an ideal way to connect your computer to a Local Area Network (LAN). After completing the steps outlined in the Quic
ページ5に含まれる内容の要旨
This manual provides a quick introduction to network technology. Please take a moment to read through this manual and get acquainted with your DI-804V. Front View LED Indicators LAN (1-4) LINK (Green) Green LED will LIGHT when link is established. Link/Act ACT (Green) Green LED will BLINK when packet is transmitting or receiving. Serial (Green) Green LED will LIGHT when a good link is established. WAN (Green) Green LED will LIGHT when a good link is established. Status
ページ6に含まれる内容の要旨
Rearview Power (5V DC) Connect the DC power adapter to the Power port WAN Connect DSL/Cable modem to the WAN Ethernet port Serial Connect a 56k modem/ISDN TA to the serial port Ports 1-4 Connect networked devices such as computers and ftp servers to the four LAN ports, which support auto crossover Reset To reload the factory default settings, press the reset button for 5-6 seconds. Pressing the Reset button will clear the current data. Product Features VPN Provides Virtu
ページ7に含まれる内容の要旨
Firewall Protection Supports general hacker attack pattern monitoring and logging PPPoE Client Supports PPPoE client function to connect to the remote PPPoE server. Virtual Server Allows the internal server to be accessible from the Internet Upgradeable New Features Allows new features to be added in the future High Performance 32 bit RISC CPU Engine With the most advanced 32 bi
ページ8に含まれる内容の要旨
IP Address Settings and Computer Settings In order to install the DI-804V you will need to check your computer’s settings and the values from your ISP. The information offered by your ISP: • Dynamic IP settings • Your fixed IP address for the gateway • Your subnet mask for the gateway • Your default gateway IP address • Your DNS IP address If you would like to use PPPoE, you will need the following values from your ISP in order to install your router: • User Name • Password
ページ9に含まれる内容の要旨
Using the Configuration Utility Launch your web browser and type the device IP address (http:// 192.168.0.1) in the browser’s address box. This IP address is the default value of your gateway. Press Enter. Note: Please make sure that the computer’s IP Address is in the same IP Address range as the DI-804V. The IP Address of the DI-804V is 192.168.0.1. All computers on your network must be within that range, for instance, the computer IP Address could be 192.168.0.x. All computers on
ページ10に含まれる内容の要旨
Basic Setup Basic setup is a step-by-step process that will let you input all the basic settings. Click BASIC SETUP A username and password screen will appear. Leave the password box empty and type admin (the default username) in the username box. Click OK The Setup Wizard’s page will appear. Note: If you choose to input a password at any time, please remember it. If you should lose the password, you will need to reset the unit. After you reset the DI-804
ページ11に含まれる内容の要旨
Time Settings Please choose your local time zone. Device IP Settings You have to give your VPN Gateway an IP address on your network. This is not the IP address from your ISP but the local internal LAN IP address. The IP address “192.168.0.1” is the default value of your gateway. Device IP Address: The internal LAN IP address of your VPN Gateway. Device IP Subnet Mask: The subnet mask can usually be left as its default entry “255.255.255.0”.
ページ12に含まれる内容の要旨
Cable/DSL ISP Settings To use the xDSL/Cable ISP settings, you must configure the router. ISP use either static or dynamic IP addresses. Check with your ISP if you are not certain which one it uses. If your ISP uses a static IP address, it means that the IP address of your router is always the same. Most ISPs use dynamic IP addresses. They assign you a new IP address every time you connect to the Internet. If you have a static IP address, do the following: Enter the IP address tha
ページ13に含まれる内容の要旨
ISP Additional Settings (PPPoE Settings) You can configure the router to use additional ISP settings. Some ISPs require PPPoE for authentication purposes. Do the following to set up PPPoE: User name: Enter the user name of your ISP account. Password: Enter the password of your ISP account. Retype password: Enter the password of your ISP account again to re- confirm. Some ISPs use Host Name and Domain Name to authenticate the user; if this is the case, you need to enter: Host Name
ページ14に含まれる内容の要旨
Modem Settings The modem dialup can be used as a backup for the xDSL/Cable connection. If you would like to use the modem dialup or VPN features you must enable the modem settings. Click on the Advanced Settings tab and enter the ISP account information. Note: If you would like to change the baud rate settings, please click on the “ADVANCED SETTINGS”. Then click on the MODEM SETTINGS button. Note: When your Cable/DSL connection comes back on-line, you will need to return to this
ページ15に含まれる内容の要旨
VPN Settings Use this screen to enable the IPSec feature. This feature allows a secure connection between two parties. The connection is made over the Internet. To enable the VPN function, check the Enable VPN checkbox and enter a string into the connection name field, then click the “ADD” button. Enabled NetBIOS Broadcast Computers running Microsoft Windows can communicate with one another using NetBIOS. Users can access remote network resources by browsing the Window Network Neigh
ページ16に含まれる内容の要旨
Incoming SPI Enter the Incoming SPI that the remote VPN Gateway will use to identify this SA. Outgoing SPI Enter the Outgoing SPI that the local VPN Gateway will use identify this SA Encryption Protocol VPN Internet Gateway supports three encryption algorithms (Null, DES, or 3DES); user can select an appropriate encryption algorithm. Encryption Key This string is used as a key to encrypt and decrypt the data transmitted. Authentication Protocol VPN Internet Gateway suppo
ページ17に含まれる内容の要旨
Save & Restart After you have finished making all the changes on the various pages, please click Save & Restart to save the settings and restart the device. After the restart, the device will function according to the saved settings. During the startup process the LED of the device will blink. Please wait until the blinking of the device stops before proceeding. 17
ページ18に含まれる内容の要旨
Device Information Device information displays the current settings of the VPN Internet Gateway. Device Name This is the host name of the VPN Internet Gateway. IP Address This is the IP address of the VPN Internet Gateway. Private LAN Mac Address This is the Mac address of the VPN Internet Gateway LAN port. Public WAN (xDSL/Cable) Mac Address This is the Mac Address of the VPN Internet Gateway WAN Ethernet port. Firmware version Displays the Firmware Version of the DI-804V
ページ19に含まれる内容の要旨
Device Status Device status displays the current connection status of the VPN Gateway. Modem Dialup The modem can be used as a dialup backup for the xDSL/Cable connection. If modem dialup is connected, it will show “Modem: Active,” otherwise it will show “Not Active”. Device IP Shows the Device IP address, private LAN Mac address and public WAN Mac address of the VPN Internet Gateway. Release and Renew Click Release button, the VPN Internet Gateway will disconnec
ページ20に含まれる内容の要旨
Advanced Settings Advanced settings include DHCP server, virtual server static routing, dynamic routing, filter settings, modem string settings and administration settings. A username and password will appear. Type “admin” in the user name box, and type the password that you have set the device (the default is no password) Click OK The Advanced Settings page will appear. DHCP Server Settings The VPN Internet Gateway’s DHCP server is enabled by default. If you would like to d
