ページ1に含まれる内容の要旨
Installation & User Guide
Dual-Flush Toilet
OVE PANACHE
OPIAZ PARLIAMENT
PERSUADE ESCALE
1102602-A2-D
ページ2に含まれる内容の要旨
Tools and Materials Thank You For Choosing Kohler Company We appreciate your commitment to Kohler quality. Please take a few minutes to review this manual before you start installation. If you encounter any installation or performance problems, please don’t hesitate to contact us. Our phone numbers are listed on the back cover. Thanks again for choosing Kohler Company. Before You Begin CAUTION: Risk of personal injury or product damage. Handle with care. Vitreous china can break o
ページ3に含まれる内容の要旨
Installation 1 Remove the existing toilet: Turn off the water supply and flush the toilet, then sponge out all remaining water from the cistern. Disconnect the supply shut-off valve (if present), and remove the old pan and cistern. CAUTION: Risk of hazardous gases. If the new toilet is not installed immediately, temporarity stuff a rag in the closet flange. 2 Define the position of connector: Place the connector onto the pan, position between outlet and waste pipe. Case 1 Case 2 Finishe
ページ4に含まれる内容の要旨
Floor fixing option 4 Bracket Drill 3/8” (10 mm) fixing holes at the marked locations on the floor and insert the anchor. Install the washer and insert the hexagon screw into the bracket then tighten the screw. Position the toilet in the installed position. Install the sleeves, tighten the screw and attach the caps. Hexagon Lag Screw Bracket Hole Anchor Washer Anchor Cap Sleeve Screw 5 Screw Drill 5/16” (8 mm) mounting holes at the marked locations. Insert anchors into the holes. Plac
ページ5に含まれる内容の要旨
Installation 6 In cistern. OVE PANACHE Tank Hose Stop Valve OPIAZ PARLIAMENT Optional Bottom Water Inlet Kit PERSUADE 148794A-NA for use on ESCALE OPIAZ PARLIAMENT PERSUADE ESCALE Kohler Co. 5 1102602-A2-D
ページ6に含まれる内容の要旨
Tank fixing option 7 Position the cistern on the pan by centering the gasket on the pan inlet. Assemble the retaining washing and sealing washer to the screw. Securely tighten the screw so the cistern is level. * Optional for different product Gasket Screw Screw Plastic* Washer Nut Brass* Retaining Washer Plan Washer Fiber Washer Sealing Washer Screw 8 Connect the supply shut-off valve to the supply hose and connect supply hose to toilet supply shank. Water Supply Hose Water Supply Hose (
ページ7に含まれる内容の要旨
Install the Push Buttons 1 Disassemble the push rods. 2 Using the push rod, measure the distance between the flush valve and the top of the tank lid. Mark this lengh and cut the push rod to length. Cut the push rod to length. 3 Reassemble the push rods. 4 Fit the lid and test the buttons. Adjust the rods as required. Kohler Co. 7 1102602-A2-D
ページ8に含まれる内容の要旨
Install Flush Valve Flush Valve A 1 Release flush valve by turning righ 2 Assembly flush valve by pushing and pull straight up on the canister. straight down into the canister and turning left. 2 1 1 2 Flush Valve B 1 Release flush valve by squeezing 2 Assembly flush valve by pressing it the tabs on both side of the canister into the flush valve so it snaps into and pulling straight up out of the place. flush valve. 1102602-A2-D 8 Kohler Co.
ページ9に含まれる内容の要旨
Kohler Co. 9 1102602-A2-D
ページ10に含まれる内容の要旨
1102602-A2-D 10 Kohler Co.
ページ11に含まれる内容の要旨
Kohler Co. 11 1102602-A2-D
ページ12に含まれる内容の要旨
CONTACT AND WARRANTY INFORMATION For warranty information, please visit our website Australia www.au.kohler.com. New Zealand www.kohler.co.nz CALL US FOR HELP NEW ZEALAND A U S T R A L I A KOHLER NZ LTD KOHLER CO. Free Ph: 0800 564 537 (0800 KOHLER) Free Ph: 1300 658 277 Free Fax: 0800 664 488 Free Fax: 02 9618 1189 www.kohler.co.nz www.au.koh ler.com 1102602-A2-D
