ページ1に含まれる内容の要旨
EN
GUIDEBOOK
HARD DISK CAMERA
U
GZ-HD320
U
GZ-HD300
Dear Customers
Thank you for purchasing this camcorder.
Before use, please read the safety
information and precautions contained
in pages 2 and 3 to ensure safe use of
this product.
For Future Reference:
Enter the Model No. (located on the
bottom of the camcorder) and Serial No.
(located on the battery pack mount of the
camcorder) below.
Model No.
Serial No.
ENGLISH
ページ2に含まれる内容の要旨
Safety Precautions When the equipment is installed in a cabinet or on CAUTION a shelf, make sure that it has sufficient space on all RISK OF ELECTRIC SHOCK DO NOT OPEN sides to allow for ventilation (10 cm (3-15/16") or more on both sides, on top and at the rear). CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, Do not block the ventilation holes. DO NOT REMOVE COVER (OR BACK). (If the ventilation holes are blocked by a NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
ページ3に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS Remember that this camcorder is intended for 1. Read these instructions. private consumer use only. 2. Keep these instructions. Any commercial use without proper permission 3. Heed all warnings. is prohibited. (Even if you record an event such 4. Follow all instructions. as a show, performance or exhibition for personal enjoyment, it is strongly recommended that you 5. Do not use this apparatus near water. obtain permission beforehand.) 6. Clean only with dry c
ページ4に含まれる内容の要旨
Easy Start Guide Charge the battery before recording Turn off the camcorder and attach the battery pack. Access lamp Power/charge lamp blinks: Accessing files blinks: Charging goes out: Charging finished Do not remove the AC adapter, the battery pack or the Open the cover microSD card when the lamp is blinking. The battery pack is not charged at the time of Battery Pack purchase. AC Adapter To AC Outlet (110V to 240V) CAUTION Be sure to use JVC battery packs. If you use any other battery p
ページ5に含まれる内容の要旨
Select the city closest to Date/Time Setting T the area where you use Open the LCD monitor to the camcorder Q turn on the camcorder Power button LCD monitor Select [ON] if daylight U saving time is observed Select [YES] within R 10 seconds Slide your finger up and down on the sensor. Then touch OK. Set the date and time V Touch sensor: Sets the date and time : Moves the cursor to the right } When the message disappears, press the • OK: Clock starts power button for at least 2 seconds to
ページ6に含まれる内容の要旨
Video recording CAUTION Before recording an important scene, it is recommended to conduct a trial recording. Slide the mode switch to select ! (video) mode Q Select recording mode (REC) R The mode changes when you press the button. The auto recording indicator appears. Start recording S Remaining space on the hard disk Record-standby Video Quality Press the START/STOP button to start recording, and press it again to stop. Recording EN
ページ7に含まれる内容の要旨
Playing back Select playback mode (PLAY) Q The mode changes when you press the button. Select the desired file R Index screen Select (Touch OK) F S Playback screen To perform operations such as forward search or reverse search ( Z p. 24) To view files on TV ( Z p. 32) CAUTION Do not forget to make copies after recording! To copy files onto discs ( Z p. 47) • To dub files to a VCR/DVD recorder ( Z p. 53) • To play back a created disc ( Z p. 50) • To edit files on your computer ( Z p.
ページ8に含まれる内容の要旨
Contents GETTING STARTED EDITING Accessories ............................................10 Managing Files ........................................35 Preparing the Remote Control ...................... 11 Capturing a Still Image from a Video ............ 35 Deleting Files ................................................ 35 Index ........................................................12 Protecting Files ............................................. 37 Indications on LCD Monitor .................
ページ9に含まれる内容の要旨
How to use the Touch Read This First! Sensor Make a backup of important recorded data It is recommended to copy your important After the menu is displayed on the LCD recorded data to a DVD or other recording monitor: media for storage. JVC will not be responsible for any lost data. Make a trial recording Before the actual recording of important data, make a trial recording and play back the recorded data to check that the video and sound have been recorded correctly. Reset the camcorder
ページ10に含まれる内容の要旨
GETTING STARTED Accessories AP-V20U BN-VF808U AC Adapter Battery Pack Component Cable AV Cable CR2025 RM-V751U USB Cable Remote Control Lithium Battery CD-ROM Pre-installed in the remote control. NOTE Make sure to use the provided cables for connections. Do not use any other cables. 10 EN
ページ11に含まれる内容の要旨
Preparing the Remote Control A battery is included inside the remote control at the time of purchase. Remove the insulation sheet before use. Beam Effective Area To Reinsert the Battery Pull out the battery holder by pressing the lock Remote Sensor tab. Lock Tab Lithium Battery (CR2025) Effective distance: Max. 5 m (16 ft) NOTE The transmitted beam may not be effective or may cause incorrect operation when the remote sensor is directly exposed to sunlight or powerful lighting. EN 11
ページ12に含まれる内容の要旨
Index NOTE Be careful not to cover 3, 4, 5, and 6 • during shooting. The LCD monitor can rotate 270°. • 1 EN
ページ13に含まれる内容の要旨
Camcorder Remote Control ! Power Button Q Infrared Beam Transmitting Window # HDMI Mini Connector ( Z p. 32) R ZOOM (T/W) Buttons (Zoom in/Out) $ Component Connector ( Z p. 32) S Up Button % DISPLAY Button ( Z p. 15) T Skip Backward Button & Speaker ( Ventilation hole U Left Button ) Zoom Lever ( Z p. 22) V Back Button Speaker Volume Control W PLAYLIST Button * SNAPSHOT Button ( Z p. 21) X START/STOP Button + Touch Sensor Y S.SHOT(SNAPSHOT) Button , OK Button Z INFO Button - MENU Button a Skip F
ページ14に含まれる内容の要旨
Indications on LCD Monitor During both Video and Still Image During Video Recording Only Recording NOV. 1. 2009 4:55 PM ! Mode Indicator # EXPORT Mode Indicator ( Z p. 59) ! Selected Recording Mode Indicator $ Counter ( Z p. 29) % Upload Mode Indicator ( Z p. 61) @: Auto Mode & Video Quality ( Z p. 64) 3: Manual Mode ( Remaining Time # Effect Mode Indicator ( Z p. 31) ) REC: (Appears during recording.) $ Tele Macro Mode Indicator ( Z p. 31) M M Q: (Appears during record-standby % LED Light
ページ15に含まれる内容の要旨
During Video Playback During Still Image Playback 8 NOV. 1. 2009 4:55 PM NOV. 1. 2009 4:55 PM ! Mode Indicator ! Mode Indicator # Wipe/Fader Effect Indicator ( Z p. 26) # Quick Review Indicator ( Z p. 21) $ Playlist Playback Indicator (Appears when $ Folder/File Number playing back a playlist.) ( Z p. 44) % Slide Show Playback Indicator % Quick Review Indicator ( Z p. 20) & Battery Indicator & Video Quality ( Z p. 64) ( Date/Time ( Z p. 16) ( Counter ) Output with 1080p ( Z p. 67) ) Playback Mod
ページ16に含まれる内容の要旨
Necessary Settings before Use To detach the battery pack Charging the Battery Pack 1 Close the LCD monitor to turn off the camcorder. 2 Attach the battery pack, then connect the AC adapter. NOTE You can also use the camcorder with just the • AC adapter. The actual recording time may shorten • depending on the recording environment, such as when recording scenes with fast moving subject. Please do not pull or bend the AC adapter • plug and cable. This may damage the AC AC Adapter ada
ページ17に含まれる内容の要旨
5 Select [CLOCK SETTING]. 6 Select the city closest to the area you are traveling. 6 Select the city closest to the area To return to the previous screen where you use the camcorder. Selected area is highlighted Select @. To quit the screen Principal city of the Select [QUIT]. selected area Time difference to GMT Language Setting 7 Select [ON] if daylight saving time is The language on the display can be changed. observed. 1 Open the LCD monitor to turn on the camcorder. 2 Touch MENU.
ページ18に含まれる内容の要旨
Other Settings Grip Adjustment Tripod Mounting Align the camcorder stud hole with the tripod stud, and the mounting socket with the screw, and then rotate the camcorder clockwise to mount it to the tripod. NOTE Do not use a tripod on unsteady or unlevel surfaces. It could tip over, causing serious damage to the camcorder. NOTE Fasten the strap when you grip the • camcorder. When carrying the camcorder, please be • careful not to drop it. 1 EN
ページ19に含まれる内容の要旨
To remove a microSD card Using a microSD Card Push the microSD card once. After the card comes out a little, pull it out. The camcorder is programmed to record on NOTE the built-in hard disk when it is shipped from the factory. You can change the recording Insert and remove the microSD card only • medium to microSD card. while the power is turned off. Otherwise, data Operations are confirmed on the following on the card may be corrupted. • microSD cards. Do not touch the terminal on t
ページ20に含まれる内容の要旨
RECORDING/PLAYBACK Recording Files Video Recording Slide the mode switch to select Press PLAY/REC to select the ! (video) mode. recording mode. SNAPSHOT Press START/STOP to start recording. Approximate remaining time for recording You can also start/stop recording by selecting [REC] on the LCD monitor. (On-screen recording control) To stop recording To change the video quality Press START/STOP again. Change the settings in [VIDEO QUALITY]. ( Z p. 64) To view the last recorded scene Se
