ページ1に含まれる内容の要旨
10/100 Bridging Converter
KS-220F series
Model:
KS-220F/T
KS-220F/C
KS-220F/S
KS-220F/S-A
KS-220F/S-3
KS-220F/S-5
-12-
ページ2に含まれる内容の要旨
! " #
$
% &
ページ3に含まれる内容の要旨
! "!#"#$#% TRADEMARKS WARNING:
! " #$ %&
ページ4に含まれる内容の要旨
Table of Contents Chapter 1 Introduction Introduction............................................................................... 1 Features ................................................................................... 2 Specifications .......................................................................... 3 Chapter 2 Installation Unpacking ................................................................................. 4 Installation ................................................
ページ5に含まれる内容の要旨
1. Introduction
-6--
-6--7 "
$ 3
'
-6--7 8'
' 2
-6--7 8'
--7
"
- --7
%
0
--7
%
8'
9
% "
9:
%
9:
ページ6に含まれる内容の要旨
Features ; :
333 .-2, --)93"* --)93"$* 333 .-2, -)93"
; 2
& ' " -6--7 ' ' 2 "
-6--7 ' --7 $
;
' & "
--7 -7
" "
5
; 3 '
7<"* =
7< =
0
" 8'
; 3
ページ7に含まれる内容の要旨
Specifications 9 & -)93"% --)93"*% --)93"$* :
& ' " 2 ?@"AB = ' 2 " 2 ?@"AB =
:
& -)93" " : ,% A% B 8'
--)93"* " : B 8'
--)93"$* " +2B62Bµ 77
--)93"$* " 62Bµ 97
>3< & >6 >3<
% <
06: >3<
% 9
>3<
% '
>3< $* >3< ' 2 $
& 7:
$
& A%..- -7 3
ページ8に含まれる内容の要旨
2. Installation Unpacking :
;
;
; (
:
Installation
"
"
"
-4-
ページ9に含まれる内容の要旨
Checking AC Power (
:
)
%
:
:
<:
:
:
& ; :
& :
; <:
&C2 D<: .-- ; <:
&
:
ページ10に含まれる内容の要旨
3. Making Network Connections Two Switched Ports
Configuration Switches (
% ' ' 2
& Port 1, Port 2 SW1 Off Auto-negotiation is enabled. On Auto-negotiation is disabled. Port 1, Port 2 SW2 Off 100Mbps is used. (When SW1 = On) On 10Mbps is used. (When SW1 = On) Port 1, Port 2 SW3 Off Full-duplex is used. (When SW1 = On) On Half-duplex is used. (When SW1 = On) Port 2 only S
ページ11に含まれる内容の要旨
Important Note: If any change are made to the configuration switch settings, the power to the unit must be turned off and turned on again before the changes can take effect.
"
0
5
"
%
ページ12に含まれる内容の要旨
UTP Connections
8'
'
" 8'
5
' ' 2
%
' 2 95A
($$ <
%
& Connected Device SW1 setting Port Operation Mode 10M Ethernet hub AUTO 10BASE-T, half-duplex 100M Fast Ethernet hub AUTO 100BASE-TX, half-duplex 10/100M dual speed hub
ページ13に含まれる内容の要旨
Fiber Port and Fiber Connection 5
--)93"$*
%
' 2 95A
( *""?*
9
"
" %
95 (
95
($$%
"
0
G
& Model /T model /C model /S series Fiber mode Multimode Multimode S
ページ14に含まれる内容の要旨
78>7(<3 $)3? :)>3 Connected device Duplex type Maximum length 100Base-FX NIC card Half-duplex 400 meters 100Base-FX NIC card Full-duplex 2K meters 100Base-FX hub port *1 Half-duplex 185 meters 100Base-FX hub port *2 Half-duplex 110 meters 100Base-FX switched port Half-duplex 400 meters 100Base-FX switched port Full-duplex 2K meters *1 : One Class II hub network *2 : Two Class II hub network 9 >3 7(<3 $)3? :)>3 Connecting to Duplex type Maximum length 100Base-FX NIC card Full-duplex 15Km
ページ15に含まれる内容の要旨
4. Interpreting LED Indicators
>3< & Power State Indication Interpretation On Normal The power of the unit is on. Off Problem No power is being supplied to the unit. Link/Act. (Link/Activity) State Indication Interpretation On Normal An active link is established. Off Normal No active link Blink Normal There are data transfer activities Duplex/Col (Full-duplex/Collision) State Indication Interpretation On Normal Full-duplex mode is used.
