ページ1に含まれる内容の要旨
XR-C8100/C8100R
SERVICE MANUAL
AEP Model
UK Model
XR-C8100R
E Model
XR-C8100
Photo : XR-C8100R
Model Name Using Similar Mechanism XR-C7200/C7200W
Tape Transport Mechanism Type MG-25D-136
SPECIFICATIONS
AM (C8100)
Cassette player section
Tuning range AM tuning interval:
Tape track 4-track 2-channel stereo
9 kHz / 10 kHz switchable
Wow and flutter 0.08 % (WRMS)
531 - 1,602 kHz
Frequency response 30 - 20,000 Hz (C8100)
(at 9 kHz step)
10 - 20,000 Hz (C8100R)
530 - 1,710 kHz
Signal-to-noise ratio
(a
ページ2に含まれる内容の要旨
General TABLE OF CONTENTS Outputs Line outputs (3) Power antenna relay control 1. GENERAL lead Power amplifier control Location of Controls ............................................................... 3 lead Getting Started ........................................................................ 4 Telephone ATT control Setting the Clock .................................................................... 4 lead Illumination control lead (C8100) Cassette Player ................................
ページ3に含まれる内容の要旨
SECTION 1 GENERAL This section extracted from XR-C8100R’s instruction manual. – 3 –
ページ4に含まれる内容の要旨
– 4 –
ページ5に含まれる内容の要旨
– 5 –
ページ6に含まれる内容の要旨
– 6 –
ページ7に含まれる内容の要旨
– 7 –
ページ8に含まれる内容の要旨
– 8 –
ページ9に含まれる内容の要旨
– 9 –
ページ10に含まれる内容の要旨
– 10 –
ページ11に含まれる内容の要旨
– 11 –
ページ12に含まれる内容の要旨
– 12 –
ページ13に含まれる内容の要旨
– 13 –
ページ14に含まれる内容の要旨
– 14 –
ページ15に含まれる内容の要旨
– 15 –
ページ16に含まれる内容の要旨
– 16 –
ページ17に含まれる内容の要旨
– 17 –
ページ18に含まれる内容の要旨
SECTION 2 DISASSEMBLY Note : Follow the disassembly procedure in the numerical order given. 2-1. COVER 1 claw 4 cover 3 claws 2 claw 2-2. FRONT PANEL ASSY 3 Push the bearing (L). 2 Push the bearing (R). 4 front panel assy 1 Push the button (open). – 18 –
ページ19に含まれる内容の要旨
2-3. SUB PANEL ASSY 4 claws 7 CN500 3 PTT 2.6x6 6 CN802 5 claw 2 PTT 2.6x6 1 PTT 2.6x6 8 sub panel assy 2-4. MECHANISM DECK 1 screws (2.6x6) (C TIGHT) 4 mechanism deck 2 CN201 3 CN250 – 19 –
ページ20に含まれる内容の要旨
2-5. MAIN BOARD 3 ground point screw 4 ground point screws 2 PTT 2.6x10 5 MAIN board 6 insulated plate 1 PTT 2.6x10 2-6. HEAT SINK 1 CN551 2 J10 9 heat sink 4 cord (with connector) (INVERTER) 3 PTT 2.6x10 7 PTT 2.6x10 8 PTT 2.6x10 6 cord (with connector) 5 PTT 2.6x10 (ANTENNA) – 20 –
