ページ1に含まれる内容の要旨
INSTALLATION ANd OPERATION INSTRUCTIONS
CUSTOm PASS-ThRU bACk b AR CAbINET — SELf CONTAINEd ANd REmOTE
mOdEL NOS.
PS Series
Pr Series
PS Series
PR Series
ImPORTANT INfORmATION
Table of Contents
Fill out the enclosed warranty card and mail to the
PreP aring the Cabinet
Perlick Corporation to register the warranty. if the
card is not returned, the warranty period will begin Specifications .....................................................2,3
from the date the equipment is shipped from the
ページ2に含まれる内容の要旨
installation and Operating instructions Sizes and Specifications Custom Pass-t hru Cabinets – Self Contained mOdEL NOS. PS60 PS84* nUM ber OF DOOr S 2 Door 3 Door Cabinet Length 60” (1524) 84” (2134) 3 3 DiMen SiOn S Depth 26 /4” (679) 26 /4” (679) 1 1 (mm) h eight 34 /2” (876) 34 /2” (876) CaSe CaPaCit Y (based on 12oz. export bottle) 12.9 20.4 1 1 COn Den Sing Unit h .P. /4 /3 r Unning LOaD –aMPS 5.7 7.8 Ship Wt. Lbs. (kg.) 380 (172) 490 (222) interi Or door sill: h igh str
ページ3に含まれる内容の要旨
installation and Operating instructions Sizes and Specifications, Custom Pass-t hru Cabinets – r emote mOdEL NOS. PR48 PR72 nUM ber OF DOOr S 2 Door 3 Door Cabinet Length 48” (1219) 72” (1829) 3 3 DiMen SiOn S Depth 26 /4” (679) 26 /4” (679) 1 1 (mm) h eight 34 /2” (876) 34 /2” (876) CaSe CaPaCit Y (based on 12oz. export bottle) 12.9 20.4 aMPS .9 .9 bt U/hr 2060 2500 Ship Wt. Lbs. (kg.) 310 (141) 400 (181) interi Or door sill: h igh strength polyethylene. door pan and ceiling
ページ4に含まれる内容の要旨
Preparing the Cabinet for Use – Pass-thru back bar Cabinets Parts List Installing Legs (Optional) ■ (2) Shelves plus (1) Floor rack-per door. attach four legs to the cabinet bottom. Use the 1 3 ■ Shelf Clips. supplied /4”- 20 x /4” hex head self-tapping machine screws. Suggested Tools Placing the Cabinet ■ #2 Phillips Screwdriver. ■ 10” Crescent Wrench. Position the cabinet into place using rollers when 9 ■ /16” allen Wrench. necessary. Important: Proper air flow around the
ページ5に含まれる内容の要旨
general information the condenser fan motor turns off and on with Refrigeration and Temperature Control the compressor. the evaporator fan motor is on the cabinet is equipped with a heavy-duty all the time. refrigeration system designed to automatically NOTE: maintain a storage temperature of 36-41 degrees F. Cabinet t emperatures lower than 34° will not the control is factory set at 38 degrees F. allow for proper defrosting of the evaporator coil. if defrosting is necessary, turn the co
ページ6に含まれる内容の要旨
replacement Parts — Pass-t hru back bar Cabinets mOdEL NOS. PS60 PS84 PR48 PR72 Condensing Units (PS Only) Condensing unit 115 volt, 60 hz. C22647 C22646 Condensing unit 515301063 515301062 Compressor 513200314 513200003 Fan motor assembly 215315009 215315009 Condenser coil 15352019 15352019 t erminal board 219101538 219101538 Overload protector Mrt 20ag K5590 Mrt 22aFZ5590 r elay 213516191 213516051 Capacitor 13556529 13556539 Evaproator Assembly Self Contained (PS) compl
ページ7に含まれる内容の要旨
reversing Door hinge STEP 9: Tools Required re-insert top hinge pin. ■ Phillips Screwdriver. ■ #4 allen Wrench. STEP 10: ■ Flathead Screwdriver or Putty Knife re-assemble lock rail from Bottom Hinge Bracket Top Hinge Bracket SteP #3 Operations to Perform on door Right hinged door (as shipped from factory) Step #14 Operations to Perform on Cabinet STEP 1: remove bottom hinge pin from assembly. STEP 2: Carefully lift and tilt out door assembly from the unit and set aside. Step
ページ8に含まれる内容の要旨
Wiring Diagram – Custom back bar Cabinets LIGHT SWITCH BLACK WHITE PR Series Remote WHITE 2 and 3 door BLACK LIGHT LIGHT LIGHT LIGHT EVAPORATOR FAN EVAPORATOR FAN BLACK WHITE THESE WIRES CAPPED IN SINGLE CABINET BLACK INSTALLATIONS RED EVAPORATOR NOTE: HOUSING FIELD WIRING FROM CABINET GROUND WIRE JUNCTION BOX TO CONDENSING CABINET UNIT MUST COMPLY WITH ALL JUNCTION BOX LOCAL AND NATIONAL ELECTRICAL CODES. CONDENSING UNIT BLACK WHITE GREEN POWER CONNECTION JUNCTION BOX FIELD INSTALLED PRESS
