ページ1に含まれる内容の要旨
,
INSTALLATION INSTRUCTIONS / OWNER S MANUAL
CD8200
AM/FM HIGH POWER DETACHABLE FACE
CD PLAYER
ページ2に含まれる内容の要旨
INTRODUCTION Congratulations on your purchase of a Profile state-of-the-art single disc CD player. Your selection of a Profile car audio product indicates a true appreciation of fine musical reproduction. Whether adding to an existing system or including your Profile CD player in a new system, you are certain to notice immediate performance benefits. FEATURES 35W x 4 Power Output Loud Function Dual RCA Line Output(Front & Rear) Power Level Meter Auxiliary RCA Line Input ISO
ページ3に含まれる内容の要旨
SAFETY PRECAUTIONS Secure the CD player . When installing your CD player in the vehicle, make sure it is mounted properly in the dash, using an after market installation kit if needed. When using the supplied mounting sleeve, it is a must that you also use the supplied back brace to support the back of the CD player. Use caution when mounting the CD player. Remember there are many electrical wires, vacuum lines, brake lines and air bag deployment wire
ページ4に含まれる内容の要旨
CARE AND MAINTENANCE Cleaning the CD player When cleaning the vehicle, be sure not to get any water in or on the CD player. Clean only the exterior surface of the unit with a dry, clean soft towel using no chemical solvents. Operating in extreme temperatures Sometimes the unit will not operate in extreme, hot or cold temperatures. If this is the case, wait until the temperature in the vehicle is normal, then resume operation. Protect your CDs. When not using the disc player, it is recommende
ページ5に含まれる内容の要旨
DISC CARE AND PLAY: Before playing, clean the disc with a clean, lint-free cloth. Wipe the disc in the direction of the arrow. Do not use solvents such as benzine or thinners. Commercially available cleaners or anti static spray will damage the unit. Insert a disc with the labeled surface up. Label surface up Do not try to insert another disc when one has already been inserted. Doing so may damage the unit. Handle the disc by its edge to keep the disc clean and do not touch the
ページ6に含まれる内容の要旨
ELECTRICAL AND SIGNAL CONNECTIONS Before making the following connections, take time to look over the vehicle's wiring and determine the location and wires you will be connecting to. If you do not wish to cut or tap into the vehicles existing factory wiring, there are wiring kits available at your car audio retailer that will allow you to plug directly into the factory wiring harness. Make sure to test all wires before connecting to the CD Player. ! Connect Black wire to chassis ground. !
ページ7に含まれる内容の要旨
TWO SPEAKER SYSTEM ANTENNA CONNECTOR AUX RCA INPUT R Low level signal output for R CH RED BROWN L L CH WHITE connection to amplifier or MEMORY +12V YELLOW 10A Fuse signal processors. BLACK(GND) + - FRONT RCA OUTPUT FILTER BATTERY R R CH RED +12V BOX BLACK L L CH WHITE RED (B+) REAR RCA OUTPUT R R CH RED 0.5A Fuse SWITCHED +12V GRAY L 0.5 A L CH WHITE (ON WITH IGNITION) BLUE AUTO ANTENNA FUSE + + + + GRAY WHITE FRONT LEFT FRONT RIGHT SPEAKER SPEAKER WHITE/BLACK GRAY/BLACK NOT
ページ8に含まれる内容の要旨
MOUNTING THE CD PLAYER There are two different ways to mount the CD Player. In most Japanese vehicles you can use the factory mounting brackets, taking advantage of the ISO/DIN opening. If your vehicle does not have ISO/DIN opening, you can mount the CD Player using the supplied DIN sleeve and rear support bracket. When considering your mounting location, make sure the unit will be leveled. If you cannot mount the CD Player level, due to your vehicles design, make sure there is no more tha
ページ9に含まれる内容の要旨
Attach the back brace to the CD player using the supplied hardware. Then attach the other end of the brace to a firm mounting surface (i.e. Dash brace, fire wall, e.t.c.) This will brace the back of the CD player to ensure solid mounting to prevent theft and provide optimal CD play. Once the CD player is secured, fit the trim ring over outside edge of the radio until it snaps into place. To Attach the Face Plate: 1 Insert the face plate with the right side first. Angle in the r
ページ10に含まれる内容の要旨
ISO/DIN MOUNTING If you own a Japanese vehicle, you can use the standard ISO/DIN mounting screw holes on the side of the CD player to attach to the existing factory mounting bracket, without using the provided DIN sleeve. ! Remove the factory ISO/DIN mounting bracket from the car along with the factory radio. ! Remove the factory radio from the bracket by unscrewing the two Phillips screws on each side of the radio paying close attention to their screw positions and saving the screws t
ページ11に含まれる内容の要旨
LOCATION AND FUNCTION OF CONTROLS 10 CD8200
ページ12に含まれる内容の要旨
1 POWER To tur n O N the unit, press any button except the and button. To tur n O F F the unit, press the button for more than seconds. 2 DETACH FACE PLATE Press the button to detach the face plate. This will allow you to remove the face plate. 3 CD PLAY To play a CD, gently insert the CD into the slot with the label side facing up. The disc will automatically be loaded into the unit and start playing the first track of the disc. The digital display will
ページ13に含まれる内容の要旨
I In CD play mode, press the 9 or 10 button to move to the next or previous track. I In CD play mode, press and hold the 9 or 10 button to fast forward or fast reverse through the song. The CD resumes playing when the button is released. 11 PRESET STATIONS There are 6 numbered buttons to store into memory and recall stations for each band. Select a band (if needed) as explained in 8 . Tune to a radio station that you wi
ページ14に含まれる内容の要旨
BEEP - The beep sound when you press a button on the unit can be turned on or off. Press the SEL button for more than 2 seconds to display the DSP function. Press the SEL button again momentarily to display BEEP ON/OFF. Then use 5 button to turn on/off the beep sound. + SEEK- The unit is equipped with two types of seeks, SEEK 1 and SEEK 2, for radio stations. Press the SEL button for more than 2
ページ15に含まれる内容の要旨
16 RANDOM PLAY In CD play mode, press the RDM 16 button to play all tracks of the disc in random sequence. Press it again to cancel random play. 17 LOUDNESS Press LOU button once to enhance the bass effect. Press again to cancel the loudness effect. 18 AUTOMATIC STORING & PRESET SCANNING In radio mode, press and hold the A.P. 18 button for more than 2 seconds to activate the automatic storing function. Once activated, the radio starts search- i
ページ16に含まれる内容の要旨
TROUBLE SHOOTING THE SYSTEM The following chart will help in solving most problems that may occur. Should any problem persist after you have made these checks, please consult your nearest Profile retailer. Before going through this check list, refer back to the wiring and operating procedures. ERROR CODES The unit cannot be operated because of trouble. Press the "RESET" button 22 . If the indicator still appears after pressing the "RESET" E 1~ E 10 Button 22 , your unit needs re
ページ17に含まれる内容の要旨
SYMPTOM CAUSE SOLUTION The compact The installation angle is Adjust the angle of the unit to less than 30 disc skips. greater than 30 degrees degrees The disc player is installed Check to see if the unit is fastened securely incorrectly with the back brace supporting the rear of the unit. The compact disc is Clean the compact disc with a compact disc extremely dirty or defective cleaning solution or replace the defective disc. compact disc. Condensation build-up on the Leave the disc player
ページ18に含まれる内容の要旨
SPECIFICATIONS GENERAL Power Supply Requirements...........................................DC 12 Volts, Negative Ground || || || || || || Chassis Dimensions ...................................................................7 (W) x 6 1/2 (D) x 2 (H) Tone Controls........................................................................................................................... Bass @ 100Hz............................................................................
ページ19に含まれる内容の要旨
LIMITED WARRANTY Profile Consumer Electronics, Inc. warrants this product to be free from defects in material and workmanship for a period of One (1) Year from the date of sale to the original consumer purchaser. If this product is proven to be defective within this one year period, Profile will repair it when said product is returned, with a copy of the dated sales receipt, freight prepaid to Profile. This warranty is valid only in the United States.
ページ20に含まれる内容の要旨
WARRANTY REPAIR POLICY In the unlikely event of product failure, the following procedures should be followed 1) The unit must be under the 1-year warranty period. 2) The unit must have no physical damage. 3) A copy of the original proof of purchase must be sent with the unit. 4) Include a brief description of the problem or failure with the unit. 5) Include the return street address and daytime telephone number. 6) Allow 2~3 weeks for rep
