ページ1に含まれる内容の要旨
Installation
Instructions
ENFIELD
T373.742
BATH/SHOWER
T373.741
TRIM KITS
T373.740
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
Certified to comply with ANSI A112.18.1
read these instructions carefully before you begin.
M968294 REV 1.1
ATTENTION:
CAUTION: Protect finish on SHOWER ARM,
INSTALL
1
If TRIM T373.742 or diverter tub spout is used SHOWER HEAD and TUB SPOUT when installing.
TRIM
m
ページ2に含まれる内容の要旨
INSTALL HANDLES 2 2 Align CROSS HANDLE (1) and push onto VOLUME CONTROL ADAPTER (2). Tighten set screw in CROSS HANDLE (1) securley with HEX WRENCH (3) supplied. 1 Align LEVER HANDLE (4) and push onto TEMPERATURE CONTROL ADAPTER (5). Tighten set screw in LEVER HANDLE (4) securley with HEX WRENCH (3) supplied. 4 5 3 TRANSPOSED SUPPLY PIPING OR BACK TO BACK INSTALLATION 3 CHECK STOP (BLUE TO RED) Should the hot and cold water supply pipes have been transposed making adjustment impossible, proceed
ページ3に含まれる内容の要旨
ENFIELD M962289-YYY0A SHOWER ARM BATH/SHOWER AND ESCUTCHEON TRIM KITS MODEL NUMBER T373.742 T373.741 T373.740 M953565-YYY0A SHOWER HEAD M962365-YYY0A ESCUTCHEON AND SCREWS M909625-YYY0A DIAL PLATE M918318-0070A HANDLE SCREW M950119-YYY0A 907090-YYY0A CROSS HANDLE ESCUTCHEON CAP ASSEMBLY A918434-YYY0A ESCUTCHEON SCREWS M950118-YYY0A LEVER HANDLE ASSEMBLY M918990-0070A SELF TAPPING HANDLE SCREW M918038-0070A HANDLE ADAPTER M950220-YYY0A DIVERTER SPOUT (IPS) M962256-YYY0A DIVERTER SPOUT REPAIR KIT
ページ4に含まれる内容の要旨
DO NOT SOLDER DIRECTLY TO THE VALVE BODY; THIS WILL DAMAGE MIXED WARNING ROUGHING-IN THE VALVE THE TEMPERATURE CONTROL ELEMENT AND CHECK STOP VALVES. Installation 1 Instructions COLD Prepare water supplies per ROUGHING-IN DIMENSIONS. Make sure the finished wall is between the minimum and maximum rough dimension. 3/4" CENTRAL THERMOSTAT R540 Install VALVE at indicated height and depth. Make sure the "TOP" marking on the PLASTER GUARD is up. WITH VOLUME CONTROL Connect the hot and cold water suppli
ページ5に含まれる内容の要旨
DO NOT SOLDER DIRECTLY TO THE VALVE BODY; THIS WILL DAMAGE MIXED WARNING ROUGHING-IN THE VALVE THE TEMPERATURE CONTROL ELEMENT AND CHECK STOP VALVES. Installation 1 Instructions COLD Prepare water supplies per ROUGHING-IN DIMENSIONS. Make sure the finished wall is between the minimum and maximum rough dimension. 3/4" CENTRAL THERMOSTAT R540 Install VALVE at indicated height and depth. Make sure the "TOP" marking on the PLASTER GUARD is up. WITH VOLUME CONTROL Connect the hot and cold water suppli
ページ6に含まれる内容の要旨
DO NOT SOLDER DIRECTLY TO THE VALVE BODY; THIS WILL DAMAGE MIXED WARNING ROUGHING-IN THE VALVE THE TEMPERATURE CONTROL ELEMENT AND CHECK STOP VALVES. Installation 1 Instructions COLD Prepare water supplies per ROUGHING-IN DIMENSIONS. Make sure the finished wall is between the minimum and maximum rough dimension. 3/4" CENTRAL THERMOSTAT R540 Install VALVE at indicated height and depth. Make sure the "TOP" marking on the PLASTER GUARD is up. WITH VOLUME CONTROL Connect the hot and cold water suppli
