ページ1に含まれる内容の要旨
Installation and Service Guide
Point of Use Water Coolers
CONTENTS
Water Cooler Specifications........................................................................ 2
Set-up & Preparation Instructions ............................................................... 3
In-shop Unit Preparation ........................................................................... 3
Installation Instructions ............................................................................. 3
Service Informatio
ページ2に含まれる内容の要旨
WATER COOLER SPECIFICATIONS Cook and Cold Models PHT1AQK, PST1AQK and PHF1AQK (-D100 series) Voltage 115VAC +10%/1 PH/60 Hertz Size 43-1/2”(109cm)H., 13-1/2”(34cm)W., 16” (41cm)D. Shipping Weight (Approx) 60 lbs. (27kg) Cold Water Capacity* .5 G.P.H. (1.9 L.P.H.) Compressor 1/20 HP Compressor (Full Load) 1.1 Amps Refrigerant R 134a Refrigerant Charge 1.875 oz. (53 grams) Hot, Cook, and Cold Models PHT1AQHK, PST1AQHK and PHF1AQHK (-D200 series) Voltage 115VAC +10%/1 PH/60 Hertz Size 43-1/2”(109
ページ3に含まれる内容の要旨
WATER COOLER SET-UP & PREPARATION INSTRUCTION will void the warranty. The manufacturer A) Inspection accepts no liability for damage caused by 1) Inspect the carton and the water cooler for evidence of rough handling and concealed excessive water pressure. damage. Damage claims should be filed with the carrier. 1) Determine the best installation location considering 2) Remove the foam packing blocks from between customer preference, electrical outlet, water line the reservoir and the cabin
ページ4に含まれる内容の要旨
2) Periodic replacement of the filter/RO cartridges 6) RO Cooler only - complete instruction 6, will be required. The frequency of the change Filter models - proceed to instruction 7. will be determined by the attributes of the source Connect a ¼” OD copper tube to the drain fitting water. Foul taste or odor may occur if filters are located on the back of the unit. This tube should not changed at proper intervals. be routed to the most convenient drain location Filter change procedure: such a
ページ5に含まれる内容の要旨
b) To Remove the Reservoir Lid: it is easiest 5) A quart (1 liter) measuring container for hot to push down slightly near the lid center and liquids. lift on each tab at the front of the lid HOT TANK CLEANING PROCEDURE individually. Once those have loosened, lift 1) Unplug the service cord and turn off water up on each of the other two corners so the supply. lid lifts as straight up as possible. This will 2) Draw water from the hot faucet until the water is help avoid the sealing edge fro
ページ6に含まれる内容の要旨
21) Plug the service cord back into the grounded yellow “service” light will illuminate indicating fused outlet and turn on the water supply. below 70% TDS reduction. This patented, solid 22) Allow the unit to fill the reservoir half full. state electronic circuit does not require service. 23) Open the hot faucet and draw water from the 4) Safer Faucets faucet until it flows freely. This water cooler incorporates the “safer faucet” 24) Draw at least one (1) quart (1 liter) of water from fo
ページ7に含まれる内容の要旨
SHUT-OFF “BALL” VALVE ASSEMBLY Part Number 031177-001 (3/8” tubing) ACCESSORIES 031177-002 (1/4” tubing) It is recommended that all units have a shut-off valve SADDLE TAPPING VALVE installed directly behind the unit. This is a safety Part Number 400306 precaution in case the unit needs to be shut off for NOTE: State and local plumbing codes may any reason. It will also help in the filter replacement prohibit the use of saddle tapping valves**. All and sanitation process. connec
ページ8に含まれる内容の要旨
REPLACEMENT PARTS BREAKDOWN 031666-011 Rev B Page 8 of 11
ページ9に含まれる内容の要旨
REPLACEMENT PARTS BREAKDOWN 031666-011 Rev B Page 9 of 11
ページ10に含まれる内容の要旨
ELECTRICAL DIAGRAM 031666-011 Rev B Page 10 of 11
ページ11に含まれる内容の要旨
® OASIS Water Cooler Limited Warranty FIRST YEAR: These parts are: hot tank, hot tank The Manufacturer promises the original thermostat, heat limiter, cold thermostat, purchaser (user) to repair or, at the compressor starting relay and overload, and Manufacturer’s option, to replace any part of mechanical float assembly. this water cooler which proves to be inoperative The labor to change the parts in the above due to a defect in material or workmanship paragraph will be the responsibility of t
