Summary of the content on the page No. 1
All products are trademarks of Nostalgia Products Group, LLC.
Worldwide design & utility patented or patents pending.
© 2010 Nostalgia Products Group, LLC.
www.nostalgiaelectrics.com
(rev. 05/12/10)
Summary of the content on the page No. 2
KRS2000 SERIES Kegorator™ Instruction Manual
Summary of the content on the page No. 3
Summary of the content on the page No. 4
ENGLISH CONTENTS IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . 3 IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . 3 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . 5 PARTS & ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . 6 WASHERS . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 REGULATOR . . . . . . . . . . . . . . . . . . . . . . . . . . 8 INSTALLING THE CASTERS . . . . . . . . . . . . . . . . . . 9 INSTALLING THE GUARDRAIL . . . .
Summary of the content on the page No. 5
IMPORTANT PRECAUTIONS 1. NEVER use an abrasive sponge, cloth or scouring pad on this appliance. 2. NEVER leave appliance unattended while in use. 3. Unplug unit from outlet when not in use and during cleaning. 4. DO NOT operate this appliance with a damaged cord or plug, or if the appliance ever malfunctions. 5. DO NOT clean any parts of this appliance in a dishwasher. 6. Keep out of reach of children. 7. This appliance is NOT A TOY. 8. Unsupervised young children and cognitively challenged i
Summary of the content on the page No. 6
ENGLISH 13. Do not operate this appliance when parts are missing or broken. 14. Do not use this appliance for commercial use. 15. This appliance is designed for indoor use only and should not be used outdoors. 16. To reduce is the risk of injury, do not allow children to play in or on the appliance. Close supervision is necessary when the appliance is used near children. 17. The appliance door must be closed during operation. Do not leave the door open when children are near the dispenser. 18.
Summary of the content on the page No. 7
INTRODUCTION To ensure that your KEGORATOR™ works to the maximum efficiency for which it was designed, keep it in a location where there is proper air circulation and electrical outlets. Choose a location where the KEGORATOR™ will be away from heat and will not be exposed to direct sunlight. • The KEGORATOR™ is designed for indoor use only. It should not be used outdoors. • The KEGORATOR™ is designed to be freestanding and should not be placed in a built-in or recessed area. • The KEGOR
Summary of the content on the page No. 8
ENGLISH PARTS & ASSEMBLY Read assembly instructions carefully before installing the KEGORATOR™ . If still unsure whether the KEGORATOR™ has been properly installed after assembly is complete, it is recommended that you contact a qualified installer. Allow the KEGORATOR™ to stand in an upright position for about 8 hours before turning on the power. Once the unit is laid on its side, the coolant in the refrigeration unit is shifted. The coolant in the refrigeration unit needs to stabilize be
Summary of the content on the page No. 9
Parts #1 Keg Coupler #2 Backflow Stopper #3 Rubber Washer #4 CO 2 Rubber (Fits D-Shankey Keg Qty. 1 Qty . 1 Directional Washer Valves) Qty. 1 Qty. 1 #5 Beer Tower Washer #6 Beer Tap/Hose #7 CO 2 Regulator #8 High Pressure Qty. 1 Assembly Qty. 1 Washer, White Qty. 1 Nylon Qty. 1 #9 CO 2 Tank Valve #10 Guard Rail #11 Drip Tray Grate #12 Drip Tray Pan Qty. 1 Qty. 1 Qty. 1 Qty. 1 #13 Rubber Foot #14 Keg Base Board #15 Me
Summary of the content on the page No. 10
ENGLISH REGULATOR The Double Regulator works the CO Tank and measures PSI (pounds 2 per square inch), as well as the volume of the CO gas in the Cylinder. 2 Set Output Pressure Gauge between 8-12 PSI for a nice, frothy head. Output Pressure Gauge (0-60 PSI) for measuring PSI Screw adjusts of CO outflow the output 2 from Tank to Keg pressure. (8-12 PSI recommended). Tank Pressure Gauge CO Shut Off 2 (0-3000 PSI) Valve (shown in for measuring open position) PSI of CO 2 Press
Summary of the content on the page No. 11
INSTALLING THE CASTERS Follow the steps below to install the Casters. 1. Empty the inside of the cabinet completely and lay the KEGORATOR™ down on it’s side. We recommend that you place a piece of cardboard or cloth underneath the cabinet to prevent dents or scratches. 2. Place washers over Caster bolts, then insert the Casters into the holes on the bottom corners of the cabinet. Tighten each Caster by turning the nut clockwise with a wrench (not provided in the kit). 3. Once all four
Summary of the content on the page No. 12
ENGLISH CO 2 & TAP TOWER INSTALLATION You must read and understand the steps below for the CO assembly before 2 installation. When you purchase the first keg of beer, you must also have your CO cylinder filled at your local supplier. CO tanks can be refilled at locations 2 2 such as welding supply shops, party stores, or wherever kegs are purchased. STEP 1 STEP 2 Make sure white nylon High Pressure Use Wrench to attach Double Washer (already installed) is attached Regulator to CO Tank co
Summary of the content on the page No. 13
STEP 6 STEP 7 The CO Connect the 2 Rubber CO line from 2 Directional the Double Washer goes Regulator back into the to the Keg Keg Coupler. Coupler. STEP 8 STEP 9 Place the Tap Tower on the Make sure the notches in the Tap KEGORATOR™ and feed the Tower fit into the holes in the top of the hose line through the hole in the KEGORATOR™ . Tighten the Tap Tower top of the KEGORATOR™ . by twisting until it locks in place. STEP 10 STEP 11 Place Coupler Washer (#3) After the Tap Tower has be
Summary of the content on the page No. 14
ENGLISH Complete CO 2 Tank Installation CO Bottle 2 Double Regulator Beer Tower Tap/ Hose Assembly Connects Beer Tap to Keg Coupler CO Tank Band 2 Large Butterfly Nut Secures Hose to Beer Tap CO Bottle 2 Beer Tap Handle Air Hose Connects Regulator to Bottom of Keg Coupler Part Connects to Keg DANGER! CO can be dangerous! CO cylinders contain 2 2 high-pressured gas, which can be hazardous if handled improperly. They must be handled with care. Location of Temperature Gauge The temperature
Summary of the content on the page No. 15
E E S S II W W TAPPING THE BEER KEG (SINGLE VALVE-TYPE KEG) Connect to the Connect to the Connect to Connect to Beer Line Beer Line T Tube ube CO2 Gas CO2 Gas Line Line T Tube ube Blac Black pull handle k pull handle Keg Coupler Keg Coupler Beer K Beer Keg Nec eg Neck k fig. 1 fig. 2 fig. 3 Lift Upright Lift Upright Beer K Beer Keg eg K Keg Suppor eg Supportt fig. 4 fig. 5 Follow these steps below to tap the beer keg. 1. Make sure the black pull handle of the couple
Summary of the content on the page No. 16
ENGLISH HELPFUL TIPS • It is recommended that you flush the hoses with water prior to first use to remove any dust and debris from shipping. • Only open the CO Tank ¼ turn to begin with and then use the regulator 2 to adjust to desired pour. If it is not enough, continue to open the CO 2 Tank by ¼ turn and use regulator until desired setting is reached. • It is normal to see condensation form on the faucet. It is caused by the difference in temperature between the cold beer and the insid
Summary of the content on the page No. 17
RETURNS & WARRANTY SHOULD YOUR UNIT NOT WORK OR IS DAMAGED WHEN YOU FIRST TAKE IT OUT OF THE BOX, PLEASE RETURN IT TO THE PLACE OF PURCHASE IMMEDIATELY. KEGORATOR™ / KRS2000 SERIES Should you have any questions, please contact us via email or at the customer service number listed below between the hours of 8:00 AM and 5:00 PM, Monday through Friday, Central Standard Time. Distributed by: Nostalgia Products Group LLC 1471 Partnership Dr. Green Bay, WI 54304-5685 Customer Service Phone: (
Summary of the content on the page No. 18
Summary of the content on the page No. 19
Summary of the content on the page No. 20
