Summary of the content on the page No. 1
TD-8817
ADSL2/2+ Ethernet/USB Router
Rev ：1.0.0
Summary of the content on the page No. 2
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2007 TP-LINK TECHNOLOGIES CO.,
Summary of the content on the page No. 3
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guaran
Summary of the content on the page No. 4
Package contents The following contents should be found in your box: One TD-8817 ADSL2/2+ Ethernet/USB Router One AC power Adapter for TD-8817 ADSL2/2+ Ethernet/USB Router Quick Installation Guide One RJ45 cable One USB cable Two RJ11 cables One ADSL splitter (only for Annex A) One Resource CD , including: This User Guide USB Driver Other Helpful Information Note: If any of the listed contents are damaged or missing, please contact the retailer from whom you purcha
Summary of the content on the page No. 5
CONTENT Chapter 1. Introduction ........................................................................................ 1 1.1 Product Overview...................................................................................................... 1 1.2 Main Features ........................................................................................................... 1 1.3 Conventions ......................................................................................................
Summary of the content on the page No. 6
4.6.3 Firmware.........................................................................................................................47 4.6.4 System Restart...............................................................................................................49 4.6.5 Diagnostic.......................................................................................................................50 4.7 Help.............................................................................
Summary of the content on the page No. 7
TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Chapter 1. Introduction 1.1 Product Overview Thank you for choosing the TD-8817 ADSL2/2+ Ethernet/USB Router. The device is designed to provide a simple and cost-effective ADSL Internet connection for a private Ethernet network. TD-8817 connects to an Ethernet LAN or computers via standard Ethernet ports. The ADSL connection is made using ordinary telephone line with standard connectors. Multiple workstations can be networked and connec
Summary of the content on the page No. 8
TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Built-in firewall, supports IP/MAC filter, Application filter and URL filter. Supports Virtual Server, DMZ host and IP Address Mapping. Supports Dynamic DNS, UPnP and Static Routing. Supports system log and flow Statistics. Supports firmware upgrade and Web management. 1.3 Conventions The Router or device mentioned in this User guide stands for TD-8817 without any explanations. Parameters provided in the pictures are just references
Summary of the content on the page No. 9
TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Chapter 2. Hardware Installation 2.1 The Front Panel Figure 2-1 The LEDs are located on the front panel, they indicate the device’s working status. For details, please refer to LED Explanation. LED Explanation: Indicator Description Status Function Details On Connection to telecom network is OK USB USB status Off Connection on USB port is abnormal Flash Data is transmitting or receiving On Connection to telecom network is OK LAN
Summary of the content on the page No. 10
TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Method two ：Restore the default setting from “Maintenance-SysRestart” of the Router's Web-based Utility. LAN: Through the port, you can connect the Router to your PC or the other Ethernet network devices. USB: Connect with your computer’s USB interface LINE: Through the port, you can connect the Router with the telephone. 2.3 Installation Environment The Product should not be located where it will be exposed to moisture or excessive h
Summary of the content on the page No. 11
TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 2-3 5
Summary of the content on the page No. 12
TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Chapter 3. Quick Installation Guide 3.1 Configure PC After you directly connect your PC to the TD-8817 or connect your adapter to a Hub/Switch which has connected to the Router, you need to configure your PC’s IP address. Follow the steps below to configure it. Step 1: Click the Start menu on your desktop, right click My Network Places, and then select Properties (shown in Figure 3-1). Figure 3-1 Step 2: Right click Local Area Conne
Summary of the content on the page No. 13
TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 3-2 Step 3: Select General tab, highlight Internet Protocol (TCP/IP), and then click the Properties button. Figure 3-3 7
Summary of the content on the page No. 14
TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Step 4: Configure the IP address as Figure 3-4 shows. After that, click OK. Figure 3-4 Note: You can configure the PC to get an IP address automatically, select “Obtain an IP address automatically” and “Obtain DNS server address automatically” in the screen above. Now, you can run the Ping command in the command prompt to verify the network connection. Please click the Start menu on your desktop, select run tab, type cmd or command in
Summary of the content on the page No. 15
TD-8817 ADSL2/2+ Ethernet/USB Router User Guide If the result displayed is similar to the screen shown below, it means that your PC has not connected to the Router. Figure 3-6 You can check it follow the steps below: 1) Is the connection between your PC and the Router correct? The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should be lit. 2) Is the TCP/IP configuration for your PC correct? If the Router's IP address is 192.168.1.1, your PC's IP ad
Summary of the content on the page No. 16
TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 3-7 Step 3: You will see Figure 3-8 as follow, please wait a moment. Figure 3-8 Step 4: After that, you will see Figure 3-9. Click Finish to complete the installation. 10
Summary of the content on the page No. 17
TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 3-9 Note: 1) All of the above settings are under windows XP. 2) If you want to pull out the USB device you must disconnect the network of USB first. 3) In the Vista operating system, maybe the “Unknown Device” screen will pop up when you insert the USB cable of the Router to a computer, please just unplug the USB cable and try again. 3.3 Login Once your host PC is properly configured, please proceed as follows to use the Web-
Summary of the content on the page No. 18
TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 3-10 Step 1: Select the Quick Start tab, then click RUN WIZARD, and you will see Figure 3-11. Click the NEXT button. Figure 3-11 Step 2: Change the login password in Figure 3-12, and then click the NEXT button. Figure 3-12 Step 3: Configure the time for the Router, and then click the NEXT button. 12
Summary of the content on the page No. 19
TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 3-13 Step 4: Select the connection type to connect to the ISP (We select PPPoE/PPPoA mode for example here), and then click the NEXT button. Figure 3-14 Step 5: Configure the following options provided by your ISP: Username, Password, VPI, VCI and Connection Type. Then click Next. Figure 3-15 13
Summary of the content on the page No. 20
TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Note: In Quick Start, you shouldn’t configure the PVC which uses the same VPI/VCI as the seven default PVCs in factory configuration does. Step 6: Click NEXT to finish the Quick Start. Figure 3-16 14
