Summary of the content on the page No. 1
TK-C215VP4_JP.book Page 1 Wednesday, September 20, 2006 6:02 PM
DOME CAMERA
INSTALLATION PRECAUTIONS
TK-C215VP4
TK-C215VP12
To installation contractor
: Be sure to read the followings beforehand for proper installa-
tion. Pass the manual to user after reading.
To user
: Please be sure to keep together with the instruction manual
after reading.
LST0474-001B
Summary of the content on the page No. 2
TK-C215VP4_JP.book Page 2 Wednesday, September 20, 2006 6:02 PM Mounting screws for the base Safety Precautions Be sure to use M4 screw. Precautions regarding fall prevention Mounting the fall prevention wire Note: warning ● Pay attention to the length, strength, routing and material (insulation properties) of the fall prevention wire used. Mounting to a firm place. ● The internal diameter of the rounded portion When mounting this un
Summary of the content on the page No. 3
TK-C215VP4_JP.book Page 3 Wednesday, September 20, 2006 6:02 PM Inserting the silica gel supplied Precautions for proper Take out the silica gel from the aluminum installation package, insert it into the silica gel insertion space of the camera unit and fasten using the lug plate. Precautions regarding water-proof and dust-proof Fill the hole with sealing material Fill the piping hole as well as the 2 mounting holes mounted with screws using a sealing material. Silica Gel Insertion
Summary of the content on the page No. 4
TK-C215VP4_JP.book Page 4 Wednesday, September 20, 2006 6:02 PM Binding the sealing tape. Precautions for proper (When mounting the camera using the pipe) installation (continued) Bind at least 2 layers of the sealing tape to the joint of the pipe (point where the thread of the piping hole coincides with the screw hole of the Precautions regarding water-proof and pipe). dust-proof (continued) Precautions when mounting the Sealing Tape dome cover 12 mm(15/32 inch) and below ● Make su
Summary of the content on the page No. 5
TK-C215VP4_JP.book Page 1 Wednesday, September 20, 2006 5:48 PM DOME CAMERA INSTRUCTIONS TK-C215VP4 For Customer Use: Enter below the Serial No. which is located on the body. Retain this information for future reference. Model No. TK-C215VP4 Serial No. LST0509-001A
Summary of the content on the page No. 6
TK-C215VP4_JP.book Page 2 Wednesday, September 20, 2006 5:48 PM Introduction Safety Precautions InformationforUsersonDisposalofOldEquipment [EuropeanUnion] This symbol indicates that the electrical and electronic equipment should not be disposed as general household waste at its end-of-life. Instead, the product should be handed over to the applicable collection point for the recycling of electrical and electronic equipment for proper treatment, recovery and recycling in accordance with your
Summary of the content on the page No. 7
TK-C215VP4_JP.book Page 3 Wednesday, September 20, 2006 5:48 PM INFORMATION FOR USA DearCustomer, This apparatus is in conformance with the INFORMATION valid European directives and standards regarding electromagnetic compatibility and This equipment has been tested and found to electrical safety. comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. European representative of Victor Commany of Japan Limited.is: These limits are designed to provide
Summary of the content on the page No. 8
TK-C215VP4_JP.book Page 4 Wednesday, September 20, 2006 5:48 PM Introduction Before starting an important recording, be Safety Precautions sure to perform a test recording in order to (continued) confirm that a normal recording is possible. The unit is to be powered by a DC 12 V or an We will not provide any compensation AC 24 V power supply. whatsoever for the contents to be recorded or loss of opportunities when recording is not The unit is to be powered by a UL Listed DC pr
Summary of the content on the page No. 9
TK-C215VP4_JP.book Page 5 Wednesday, September 20, 2006 5:48 PM These are general IMPORTANT SAFEGUARDS and certain items may not apply to all appliances. IMPORTANT SAFEGUARDS 1. Read all of these instructions. 2. Save these instructions for later use. 3. All warnings on the product and in the operating instructions should be adhered to. 4. Unplug this appliance system from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 5. Do n
Summary of the content on the page No. 10
TK-C215VP4_JP.book Page 6 Wednesday, September 20, 2006 5:48 PM Introduction Thank you for purchasing this product. This instruction manual covers total 2 different (These instructions are for: TK-C215VP4U/TK- models in common as follows: C215VP4E.) TK-C215VP4U/TK-C215VP4E Before beginning to operate this unit, please read In this manual, each model number is described the instruction manual carefully in order to make without the last letter (U/E) which means the sure that the best possi
Summary of the content on the page No. 11
TK-C215VP4_JP.book Page 7 Wednesday, September 20, 2006 5:48 PM Table of Contents Introduction Safety Precautions .................................... 2 Characteristics .......................................... 6 Table of Contents ...................................... 7 Precautions for proper use of this product .................................. 8 Name of Parts ........................................... 9 Camera .......................................
Summary of the content on the page No. 12
TK-C215VP4_JP.book Page 8 Wednesday, September 20, 2006 5:48 PM Introduction therefore appear grainy and white spots may Precautions for proper use increase. When switching between colored and black-and-white images, the bright of this product portions of the screen are enhanced and the clarity of the screen may deteriorate. This is not a malfunction. Storage and Location of Use When the source voltage cuts off or drops Do not install this unit at the following during lightning or
Summary of the content on the page No. 13
TK-C215VP4_JP.book Page 9 Wednesday, September 20, 2006 5:48 PM Name of Parts Camera A B C F D E A Mounting hole 2 C Mounting Screw for Fall Prevention Wire Use these when mounting the camera to the Use this screw when mounting the fall prevention ceiling, wall or electrical box. wire to this unit. (Fall prevention wire is not (A Pg. 17)(A Pg. 25) supplied with this product.) Note: Note:
Summary of the content on the page No. 14
TK-C215VP4_JP.book Page 10 Wednesday, September 20, 2006 5:48 PM Introduction Name of Parts (continued) Camera (continued) K J I G H G Base J Protection Cover Mount the base to the ceiling, wall or electrical Upon connecting the coaxial cable, protect it by box before mounting the camera. insulating the metal part of the BNC connector (A Pg. 17)(A Pg. 25) K from the ceiling structure. H Fastening Screw for Dome Cover K Video signal output connector (BNC) This is a fastening screw for the d
Summary of the content on the page No. 15
TK-C215VP4_JP.book Page 11 Wednesday, September 20, 2006 5:48 PM Camera (Interior) Lens L X (A next page) W V M N U O P Q R S T L Rotation Knob U Tilt Fastening Screw Rotate the lens unit to adjust the inclination of Upon adjusting the angle of view, tighten the the image. (A Pg. 22) screw to ensure that camera’s angle of view does not go out of alignment when it is used at a M Rotation Center Mark (A Pg. 22) location with strong vibration. (A Pg. 22) N Fall Prevention Wire V Shooting Dire
Summary of the content on the page No. 16
TK-C215VP4_JP.book Page 12 Wednesday, September 20, 2006 5:48 PM Introduction Setting the Lens and Switches Set the video setting switches on the camera unit before mounting it. To set the switches, use a fine-tipped screwdriver. A RESET/[SPOT] F G B LL PHASE O 1 N 2 2 3 C 4 4 5 WHT. 6 7 BAL. 8 Function Selection Switch Settings Chart (Characters in bold indicate factory settings) D LH IRIS OFF ON LEVEL E 1 AGC OFF ON FOCUS ADJUST 2 SELECT PHASE WHT.BAL. 3 SYNC LL INT 4 WHT.BAL. ATW MANU 5 BL
Summary of the content on the page No. 17
TK-C215VP4_JP.book Page 13 Wednesday, September 20, 2006 5:48 PM 3. [SYNC] Synchronization system selection surveillance cameras that use infra-red switch. lighting. This switch sets the synchronizing system for ● Sensitivity increases in the case of black- the camera. and-white images. The screen may INT: therefore appear rougher and white spots This is set for internal synchronization may increase. LL (Line Lock): The camera’s vertical synchronization is 7. [RESERVED] locked to the AC 2
Summary of the content on the page No. 18
TK-C215VP4_JP.book Page 14 Wednesday, September 20, 2006 5:48 PM Installation and Connection System Example ● Turn off the power of devices to be used before connecting the cables. ● Read through the “Instruction Manual” of the devices to be used carefully before connecting. Coaxial Cable Camera 1 Power Cable Coaxial Cable Power Cable Camera 2 Coaxial Cable Power Cable Camera 3 Coaxial Cable Power Cable Camera 4 Power Unit DC12 V or AC24 V (Class 2) VIDEOINPUT AUDIOIN 1234 5678 9 10 11 12 13
Summary of the content on the page No. 19
TK-C215VP4_JP.book Page 15 Wednesday, September 20, 2006 5:48 PM DC 12 V or AC 24 V power supply cable About Connection Cables Connect the DC 12 V or the AC 24 V power The maximum connection distance varies with supply to the DC 12 V/AC 24 V terminals on the the type of cable used. Please refer carefully to terminal board. To prevent connection errors or a the table for each cable during connection. cable disconnection, we recommend the use of lug plates for the connections. The following
Summary of the content on the page No. 20
TK-C215VP4_JP.book Page 16 Wednesday, September 20, 2006 5:48 PM Installation and Connection Procedures from Set the switches (A Pg. 17) Connection to Setting step 1 Remove the dome cover, followed by setting the video image Follow the procedures below to connect/set this switches. unit. Turn off the power of devices to be used before K connecting the cables. Mounting the base Before touching the camera unit, make (A Pg. 17) step 2 sure to touch the metal surface of the Mount the base
