Summary of the content on the page No. 1
Owner's Manual & Assembly Instructions
SPl
Model No.
CM1014 D
OB1014-B Q 697.68103-B Q
CAUTION: SOME PARTS HAVE SHARP EDGES. CARE
MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES
TO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READ
712741204
SAFETY INFORMATION PROVIDED IN THIS MANUAL
BEFORE BEGINNING CONSTRUCTION. WEAR GLOVES
BUILDING DIMENSIONS
* Size rounded off to the nearest foot
WHEN HANDLING METAL PARTS.
Exterior Dimensions Interior Dimensions Door
*Approx. Foundation Storage Area (Roof Edge to R
Summary of the content on the page No. 2
BEFORE YOU BEGIN.... A2 Owner*s Manual Before beginning construction, check local building codes regarding footings, location and other requirements. Study and understand this owner's manual. Important information and helpful tips will make your construction easier and more enjoyable. Assembly Instructions: Instructions are supplied in this manual and contain all appropriate information for your building model. Review all instructions before you begin, and during assembly, follow the step sequen
Summary of the content on the page No. 3
PLAN AHEAD.... A3 Watch the Weather: Be sure the day you select to install your building is dry and calm. Do not attempt to assemble your building on a windy day. Be careful on wet or muddy ground. Teamwork: Whenever possible, two or more people should work together to assemble your building. One person can position parts or panels while the other is able to handle the fasteners and the tools. Tools and Materials: These are some basic tools and materials you will need for the construction of you
Summary of the content on the page No. 4
SAFETY FIRST.... A4 Safety precautions are important to follow throughout the construction of your building. •Care must be taken when handling various •Practice caution with the tools being used in the pieces of your building since some contain assembly of this building. Be familiar with the sharp edges. Please wear work gloves, eye operation of all power tools. protection and long sleeves when assembling or performing any maintenance on your build- ing. safetyedge sharpedge sharpedge safetyedge
Summary of the content on the page No. 5
CARE & MAINTENANCE.... A5 Web Finish: For long lasting finish, periodically clean and wax the exterior surface. Touch- up scratches as soon as you notice them on your unit. Immediately clean the area with a wire brush; wash it and apply touch-up paint per manufacturer's recommendation. Roof: Keep roof clear of leaves and snow with long handled, soft-bristled broom. Heavy amounts of snow on roof can damage building making it unsafe to enter. In snow country, Roof Strengthening Kits are available
Summary of the content on the page No. 6
ACCESSORIES.... A6 \VEB ROOF STRENGTHENING (heavy snow load) KITS Extra roof beams and gable braces designed for added protection against heavy snow accumulation. Increases the strength of your roof by 50%. ANCHOR KIT ANCHOR KIT Model No. AK100 Model No. AK4 New concrete anchor system permits Anchor Kit contains heavy-duty steeI anchoring any size Arrow building augers, 60' (18m) of steet cable and 4 cable directly to a concrete slab. Each kit clamps. No digging or concrete contains heavy-duty,
Summary of the content on the page No. 7
THIS PAGE WAS LEFT BLANK INTENTIONALLY
Summary of the content on the page No. 8
THIS PAGE WAS LEFT BLANK INTENTIONALLY
Summary of the content on the page No. 9
Foundation F09 The Foundation For Your Building OPTION 1: ARROW FLOOR FOUNDATION KIT: (Order NoFSl0 4-A or 68387-A) Arrow has the best base for your building in this simple kit. It keeps stored items above the ground. This foundation should be used with one of the following: A. To support a plywood deck 8. To be filled with sand. We recommend the combined use of 1. an ARROW FLOOR FOUNDATION KIT and 2. an ARROW ANC NORING KIT as an effective method of securing the building to the ground. Allow 1
Summary of the content on the page No. 10
Anchoring AIO it is important that the entire floor frame be anchored after the building is erected. Below are recommended ways of anchoring. Arrow Anchoring Kit: (Model No. AK4 or 60298) Anchoring into _Vood/Post: Recommended for use with any suggested base. Use 1/4" Wood Screws. There are 1/4" (O,63cm) dia. Contains: 4 Anchors with Cable, Clamps and holes provided in the frames for proper anchoring• installation instruction. OVERTHE BEABIS AND iNTO THE GROUND Arrow Anchoring Kit: (Model No. AK
Summary of the content on the page No. 11
Hardware SPll Remove from bag of screws and save for the last step T T T 65900A 65103 #f 0Bxf/2" Black Screw (4) 66923 65004 #8-32 Hex Nut (188) (Packed with Screws) #8-32x3/8" Bolt (188) #8Ax5/16" Screw (438) 66646 65109 67468 66045 Washer (453) #8-32 Acorn Nut (4) Peak Cap (2) Handle (2) (12 sheets of 40) (Packed with Screws) (Arrow Logo) 66183 66242 66382 RoofTrim Cap 6228 DoorSlide(4) Lower DoorGuide(4) (2 right &21eft) TrackSuppo_(2) 67545 21' WeatherStripping(1) 11
Summary of the content on the page No. 12
Parts List BZ12 Parts in Carton One Part Part Quantity Check Number Description in Carton List 8576 2 Right Gable 8577 Left Gable 2 6264 Horizontal Door Brace 4 7743 Roof Panel 8 9984 2 Right Roof Panel 9983 Left Roof Panel 2 8538 1 Right Door 8539 Left Door 1 9369 Door Jamb 2 9373 Front Wall Panel 2 6515 Wall Panel 12 6020 Corner Panel 4 3719 Door Handle Brace 2 6278 Vertical Door Brace 2 6403 1 Door Track Splice 6892 Rt. Side Roof Trim 2 6893 Lt. Side Roof Trim 2 6015 Side Roof Trim 2 6869 1 R
Summary of the content on the page No. 13
Parts List 8P13 Parts in Carton Two Part Part Quantity Check Number Description in Carton List 5986 2 Rear Wall Angle 10389 Rear Walt Channel 2 9365 Front Wall Channel 2 6635 Roof Beam Bracket 4 10386 Roof Beam 8 10388 Side Wall Channel 4 10391 4 Side Wall Angle 10387 Side Floor Frame 4 8936 Rear Floor Frame 2 9367 Front Floor Frame 2 9009 Gable Brace 2 9204 Roof Beam Brace 2 8934 1 Ramp 13
Summary of the content on the page No. 14
,m =. O 8934 Ramp (1) • Parts Needed For ® O 9367 Front Floor Frame (2) ® 8938 Rear Floor Frame (2) Step 1 Floor Frame Assemblies O 10387 Side Floor Frame (4) $O14 The front floor frame is made up of three pieces. The side floor frames and the rear floor frame are made up of two pieces. The holes in these 8934 pieces will align when the pieces are positioned with correct amount of overlap. The illustrations below show 9367 the proper overall length for the sides, rear and front. Proceed as follo
Summary of the content on the page No. 15
O5986Rear Wall Angle (2) St p 2 . Parts Needed For ® .10389RearWa,,Cha.ne,(2) @ Frame Assemblies ® 10388 Side Wall Channel (4) O 10391 SideWall Angle {4) S015 The main frame pieces reinforce the walls. These pieces will later be in- I I RearWaIIChannel 10389 118 1/8" 3,0m stalled in the center and at the top edge of the side walls and the rear wall. Proceed as follows: 10389 1 Overlap the rear wall channel pieces as shown in the figure and o Ilil I Side Wall Channels fasten the two pieces togeth
Summary of the content on the page No. 16
® Parts Needed For ® O10386RoofBeam(8) Step 3 Roof Beam Assemblies S016 The roof beams join the two gables 10386 and support the roof panels. The main roof beam is made up of four pieces overlapped back to back at the cen- 10386 ter. The left and right roof beam as- semblies are made up of two pieces. Hint: These pieces are force-fitted, _- RoofBeam 1593/8" 4,0m so you may have to press hard to join them together. 1 Place the end of one roof beam inside a second roof beam sothat the six holes in
Summary of the content on the page No. 17
® Parts Needed For • • 6403DoorTrackSplice(1) Step 4 Doo Track Assembly ®936sDoor, ack(21 S017 NOTE: Door Track Splice (painted part) The door track assembly supports the sliding doors and reinforces the front wail. It is made up of three pieces. 6403 1 Using the door track splice, (painted), join the door track (galvanized) pieces end-to-end as ©© shown. 2 Insert four screws from the under- 9366 @ _ 66242 side only. 9366 Long Leg on Top Hint: The holes in the top sideofthe door track assembly a
Summary of the content on the page No. 18
@ Front Floor Assembly (1) ® Parts Needed For o • Side Floor Assembly (2) Step 5 Floor Frame • Rear Floor Assembly (1) S018 you assembled earlier on the foun- L_ v dation. Assemble the four corners of the floor frame using two screws at each corner as shown. At the front corners fasten bolts through from the bottom with nuts on top. ' 9367 2 Measure the floor frame diago- When Diagonal Measurements nally. When the diagonal measure- are Equal the Floor Frame ments are equal, the floor frame is is
Summary of the content on the page No. 19
• 6515 Wall Panel (2) ® Parts Needed For ® • 9373 Front Wall Panel (2) Step 6 Corners O 6020 Corner Panel (4) S019 Narrow NOTE Side The remainder of the building assembly requires many hours and more than one Wide Side person. Do not continue beyond this point if you do not have enough time to com- plete the assembly today. A partially 6020 assembled building can be severely damaged by light winds. Each screw and bolt in the wall re- TOP VIEW SIDE SIDE quires a washer. I Position a corner panel
Summary of the content on the page No. 20
Step 7 . Parts Needed For ® ORearWallChannelAssemNy(1) _/_id Fl'*_]i_leS 0 Side Wall Channel Assembly (2) S020 The mid frame pieces give rigidity to the side and rear walls. 1 Fasten the rear wal! channel across the middle of the rear wall using screws. 2 Fasten the side wall channels across the middle of the side panels using screws. Fasten overlaps in rear corners with bolts and nuts, at two locations. See the figure. NOTE The wall channels behind the front wall panels will be installed in a l
