Summary of the content on the page No. 1
Summary of the content on the page No. 2
Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national stan
Summary of the content on the page No. 3
Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation. If these openings are blocked, built-up heat can cause failures wh
Summary of the content on the page No. 4
Important Precautions On Cleaning Unplug the display before cleaning the face of the display screen. Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display screen because over-spraying may cause electrical shock. When cleaning the product, unplug the power cord and scrub gently with a soft cloth to prevent scratching. Do not clean with a wet cloth or spray water or other liquids directly onto the product. An electric shock may occur. (Do not use chemicals such as benz
Summary of the content on the page No. 5
Accessories !!! Thank for selecting LGE products !!! Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Power Cord User's Guide/Cards 15-pin D-Sub Signal Cable DVI-D Signal Cable (To set it up, this signal cable may be (This feature is not available in all attached to this product before countries.) shipping out.) NOTE This accessories may look different from those shown here. User must use shielded signal interface cables (D-sub
Summary of the content on the page No. 6
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand 1. Place the monitor with its front facing downward on a soft cloth. 3. Assemble the Stand Base(Front, 2. Assemble the stand Body into the Rear) into the Stand Body in the product in the correct direction as shown in correct direction. the picture. Make sure you push it until you hear it “click”. Hinge Body Stand Body Sta
Summary of the content on the page No. 7
Connecting the Display Disassembling the stand 2. Place the monitor face Down on the 1. Put a cushion or soft cloth on aflat cushion or soft cloth. surface. 3. 4. Remove the Stand Body and Stand Use a coin on the back of the Stand Base from product in correct Base and turn the screw anticlock- wise to loosen. direction as shown in the picture. 6
Summary of the content on the page No. 8
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display -After installation, adjust the angle as shown below. 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5˚ to 15˚ Do not touch or press the screen when adjusting the angle of the monitor. When adjusting the angle of the screen, do not put your finger(s) in between the head of the
Summary of the content on the page No. 9
Connecting the Display E2241V/E2341V/E2341VG/E2441V Connecting with the PC 1. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. 2. Connect signal input cable and power cord in order, then tighten the screw 1 2 of the signal cable. A Connect DVI-D(Digital signal) Cable B Connect D-sub(Analog signal) Cable NOTE This is a simplified representation of the rear view. This rear view represents a gene
Summary of the content on the page No. 10
Control Panel Functions Front Panel Controls For D-SUB and DVI input Only for HDMI input MENU Button OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear. You can unlock the OSD controls at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" should appear. 9
Summary of the content on the page No. 11
Control Panel Functions SUPER ENERGY Use this button to enter SUPER ENERGY SAVING SAVING Button menus.For more information, refer to page 15 . (For D-SUB and DVI input) E2241V/E2341V/E2341VG/E2441V:1920 x 1080 (Only for HDMI input) Use this button to select source from input. INPUT Button (SOURCE Hot key) When two input signals at least are connected, you can select the input signal (D-SUB/DVI/HDMI) you want. When only one signal is connected, it is automatically detected. The default setting
Summary of the content on the page No. 12
e n . 1 s. 2 / / 3 . n 4 11
Summary of the content on the page No. 13
On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. Main menu Sub-menu Supported input Description To adjust the brightness of BRIGHTNESS MENU the screen ORIGINAL RATIO To adjust the image size COLOR TEMP To customize the color of the screen (PRESET/USER) To adjust the contrast of the CONTRAST screen To adjust the black level of the BLACK LEVEL screen LANGUAGE To customize the screen status
Summary of the content on the page No. 14
13,
Summary of the content on the page No. 15
(Only HDMI input) 14
Summary of the content on the page No. 16
15
Summary of the content on the page No. 17
Turn on the SUPER ENERGY SAV- ING function. Turn off the SUPER ENERGY SAV- ING function. Now the monitor is LED SAVING function. Clear the TOTAL POWER REDUC- TION and TOTAL CO2 REDUCTION values. 16
Summary of the content on the page No. 18
SAVING DATA(W/h) : 22 inch 23 inch 24 inch Saving Data depends on the Panel. So, those values should be different from each panel and panel vendor. LG accumulate those values using integrated function with 10 minutes broadcast v- ideo signal. LED Saving means that how much power can be saved using WLED Panel instead of CCFL panel. SUPER Saving means that how much power can be more saved using SUPER E- NERGY SAVING function. 17
Summary of the content on the page No. 19
Troubleshooting Check the following before calling for service. No image appears No image appears Is the power cord of the • Check and see if the power cord is connected display connected? properly to the power outlet. Is the power indicator • Press the Power button. light on? Is the power indicator • If the display is in power saving mode, try moving flickering? the mouse or pressing any key on the keyboard to bring up the screen. • Try to turn on the PC. Do you see an "OUT OF • This me
Summary of the content on the page No. 20
Troubleshooting Display image is incorrect Display Position is • Press the AUTO button to automatically adjust incorrect. your display image to the ideal setting. On the screen • Press the AUTO button to automatically adjust background, vertical your display image to the ideal setting. bars or stripes are visible. Any horizontal noise • Press the AUTO button to automatically adjust appearing in any your display image to the ideal setting. image or characters are not clearly portrayed. • C
