Summary of the content on the page No. 1
User’s Guide
L226WU
Make sure to read the Important Precautions before using the product.
Keep the User's Guide(CD) in an accessible place for future reference.
See the label attached on the product and give the information to your
dealer when you ask for service.
Summary of the content on the page No. 2
Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national stan
Summary of the content on the page No. 3
Important Precaautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation. If these openings are blocked, built-up heat can cause failures w
Summary of the content on the page No. 4
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand base 1. Place the monitor with its front facing downward on a cushion or soft cloth. 1 2.Rotate the Stand Body as shown in figure . 1 3. Assemble the Stand Base(Front, Rear) into the Stand Body in the correct direction. 4. Once assembled take the monitor up carefully and face the front side Stand Base Stand Body Warn
Summary of the content on the page No. 5
Connecting the Display Disassembling the stand 1. Put a cushion or soft cloth on aflat 2. Place the monitor face Down on surface. the cushion or soft cloth. 3. Pushing Latch inside, Take the stand base from stand body. Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. A4
Summary of the content on the page No. 6
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -3˚~17˚ Swivel :356˚ Height Range : maximum 5 .51 inch (140.0mm) 140.0mm * Please be sure to remove the Locking pin to adjust the height. Ergonomic It is recommended that
Summary of the content on the page No. 7
Connecting the Display Using the Computer 1. Make sure to turn off the computer and product. 2 Connect signal input cable and power cable in order, then tighten the 1 screw of the signal cable. A Connect DVI Cable B Connect D-sub Cable C Connect USB Cable Analog signal Digital signal Power Cord USB D-sub DVI AC-IN D-SUB DVI-D Wall-outlet type PC-outlet type C B DVI-D(This feature is not available in all countries.) A 2. Press button on
Summary of the content on the page No. 8
Use USB programs Connecting the USB(Universal Serial Bus) Cable 1. Plug in the USB cable as in the diagram. One USB Upstream port Two USB Downstream ports AC-IN D-SUB DVI-D Connect to downstream connectors of desktop or laptop computers, mouse, memory stick or USB hard disk. (However, the computer must support USB and have the USB port.) Tidying USB (Universal Serial Bus) Cable 1. Elevate the monitor as far as possible follow 2. Tidy the USB cab
Summary of the content on the page No. 9
Use USB programs Use USB programs The display feature can be used by easily connecting the USB cable between laptops/desktops and the USB port at the back of the monitor. System Requirements In order to make full use of USB Display features, your computer must meet the following minimum system requirements: • 1.2 GHz CPU or higher, 512 MB memory or higher (Recommended Specifications: 1.6 GHz Core2 Duo CPU, 1 GB memory) • USB 2.0 Interface • Windows 2000 (Service Pack 4), Windows XP (Servi
Summary of the content on the page No. 10
Use USB programs 4. When the installation of "LG USB Easy Connection" program is completed, icons as shown in the picture will be created in the taskbar. With these icons, you can easily use features such as Screen Resolution, Color Quality, Screen Rotation, Extend To, Extend and Mirror. ■ Screen Resolution : Provides information on the ■ Color Quality : You can choose 16 resolution that the USB supports. bit or 32 bit colors. ■ Screen Rotation : You can set the direction to display USB imag
Summary of the content on the page No. 11
Use USB programs ■ Extend To : Sets the location to display USB images. (1: Standard monitor, 3: USB Monitor) Right Left Above Below ■ Extend : Expands the display to a sub screen. ■ Mirror : Shows the same display as the main screen. ■ Off : Does not to display data to make sure USB screen is not displayed. 5. When using multiple USB monitors, you can set "LG USB Easy Connection" program separately for each monitor. 2 Select No. 3 USB monitor and use "LG USB Easy 1 In case of USB d
Summary of the content on the page No. 12
Control Panel Functions Front Panel Controls 6 SOURCE Button You can select the computer that you want to use by selecting input signal (DVI, D-Sub or USB). The default input signal is analogue (D-Sub). Use this button to enter or exit the On Screen Display. MENU Button OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear. You can
Summary of the content on the page No. 13
Control Panel Functions Use these buttons to select or adjust functions in the On - + Buttons Screen Display. For more information, refer to page A19. AUTO/SET Use this button to enter a selection in the On Screen Display. Button AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press the AUTO/SET button before entering the On Screen Display(OSD). This will automatically adjust your display image to the ideal settings for the current screen resolution size (display mode). The b
Summary of the content on the page No. 14
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making image adjustments. To make a
Summary of the content on the page No. 15
On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. Main menu Sub-menu A D USB Reference BRIGHTNESS PICTURE To adjust the brightness, contrast and gamma of CONTRAST the screen GAMMA sRGB To customize the color COLOR PRESET 6500K of the screen 9300K RED GREEN BLUE To adjust the position HORIZONTAL of the screen POSITION VERTICAL CLOCK To improve the clarity PHASE TRACKING an
Summary of the content on the page No. 16
On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears. Menu Name PICTURE Sub-menus Icons Button Tip MENU : Exit : Adjust (Decrease/Increase) + - SET : Enter : Select another sub-menu NOTE OSD (On Screen Display) menu languages on the mon
Summary of the content on the page No. 17
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description PICTURE PICTURE To adjust the brightness of the screen. BRIGHTNESS To adjust the contrast of the screen. CONTRAST Set your own gamma value. : -50/0/50 GAMMA On the monitor, high gamma values display whitish images and low gamma values display high contrast images. MENU : Exit - : Decrease : Increase + SET : Select another sub-menu COLOR COLOR PRESET Select the screen color. • sRGB: Set the screen color to fit t
Summary of the content on the page No. 18
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description POSITION POSITION HORIZONTAL To move image left and right. VERTICAL To move image up and down. MENU : Exit - : Decrease + : Increase SET : Select another sub-menu TRACKING TRACKING CLOCK To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. PHASE To adjust the focus of the display. This item allows you to remove any horizontal noise and clear or sh
Summary of the content on the page No. 19
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description LANGUAGE To choose the language in which the control names are displayed. SETUP OSD To adjust position of the OSD window POSITION on the screen. SETUP WHITE If the output of the video card is different BALANCE the required specifications, the color level may deteriorate due to video signal distortion. Using this function, the signal level is adjusted to fit into the standard output level of the video card in order to
Summary of the content on the page No. 20
On Screen Display(OSD) Selection and Adjustment The OSD screen will appear when you touch the button on the front of the monitor. Menu Name Icons Sub-menu Name FLATRON F-ENGINE Screen when applied Screen when not applied When you execute F-ENGINE, two tones will appear on the screen as shown. The applied screen will appear on the left side, whereas the non-applied screen will appear on the right side.Touch the SET button to use the adjusted screen. Main menu Sub menu D
