Summary of the content on the page No. 1
COLOR LASERJET ENTERPRISE CP4020/CP4520
SERIES PRINTER
Service Manual
CP4025n
CP4025dn
CP4525n
CP4525dn
CP4525xh
Summary of the content on the page No. 2
Summary of the content on the page No. 3
HP Color LaserJet Enterprise CP4020- CP4520 Series Printers Service Manual
Summary of the content on the page No. 4
Copyright and License Trademark Credits ® ® ® © 2009 Copyright Hewlett-Packard Adobe , Acrobat , and PostScript are Development Company, L.P. trademarks of Adobe Systems Incorporated. Reproduction, adaptation, or translation Corel® is a trademark or registered without prior written permission is prohibited, trademark of Corel Corporation or Corel except as allowed under the copyright laws. Corporation Limited. The information contained herein is subject Intel® Core™ is a trademark of Intel to ch
Summary of the content on the page No. 5
Conventions used in this guide TIP: Tips provide helpful hints or shortcuts. NOTE: Notes provide important information to explain a concept or to complete a task. CAUTION: Cautions indicate procedures that you should follow to avoid losing data or damaging the product. WARNING! Warnings alert you to specific procedures that you should follow to avoid personal injury, catastrophic loss of data, or extensive damage to the product. ENWW iii
Summary of the content on the page No. 6
iv Conventions used in this guide ENWW
Summary of the content on the page No. 7
Table of contents 1 Theory of operation Basic operation ..................................................................................................................................... 2 Sequence of operation ......................................................................................................... 3 Engine-control system .......................................................................................................................... 4 DC controller ................
Summary of the content on the page No. 8
Step 6: Secondary transfer ............................................................................... 26 Step 7: Separation ............................................................................................ 27 Step 8: Fusing ................................................................................................... 27 Step 9: ITB cleaning .......................................................................................... 28 Step 10: Drum cleaning ...................
Summary of the content on the page No. 9
Before performing service .................................................................................................................. 70 After performing service ..................................................................................................................... 70 Post-service test ................................................................................................................................. 71 Print-quality test ........................................
Summary of the content on the page No. 10
Cassette feed guide ......................................................................................................... 118 Secondary transfer assembly .......................................................................................... 119 Reinstall the secondary transfer assembly ..................................................... 120 Separation pad (Tray 1) ................................................................................................... 121 Remove the separati
Summary of the content on the page No. 11
Lifter-drive assembly ........................................................................................................ 173 Remove the lifter-drive assembly .................................................................... 173 Lifter base assembly ........................................................................................................ 175 Remove the lifter base assembly .................................................................... 175 Reinstall the lifter base as
Summary of the content on the page No. 12
Lifter-drive assembly (optional paper feeder) .................................................................. 230 Remove the lifter-drive assembly (optional paper feeder) .............................. 230 Pickup motor assembly (optional paper feeder) ............................................................. 231 Remove the pickup motor (optional paper feeder) assembly .......................... 231 Controller PCA (optional paper feeder) ...................................................
Summary of the content on the page No. 13
S Tray 3 paper present sensor ....................................................... 265 T Tray 3 feed sensor ...................................................................... 265 U Tray 3 paper surface 1 and 2 sensors ........................................ 265 V Tray 3 paper size switches .......................................................... 265 W Tray 4 paper present sensor ...................................................... 265 X Tray 4 feed sensor ............................
Summary of the content on the page No. 14
Repetitive defects ruler ................................................................................... 312 Calibrate the product ....................................................................................... 313 Control panel menus ........................................................................................................ 314 Control panel menus ....................................................................................... 314 Show Me How menu ...............
Summary of the content on the page No. 15
Envelopes jam or will not feed in the product .................................................................. 405 Output is curled or wrinkled ............................................................................................. 406 Product will not duplex or duplexes incorrectly ................................................................ 406 Use manual print modes .................................................................................................................. 4
Summary of the content on the page No. 16
Internal components (7 of 7) ............................................................................................ 450 Cassettes 2-5 ................................................................................................................... 452 Paper pickup assembly .................................................................................................... 454 Tray 1 paper pickup assembly ....................................................................................
Summary of the content on the page No. 17
Return and recycling instructions ..................................................................................... 508 United States and Puerto Rico ........................................................................ 508 Multiple returns (more than one cartridge) ..................................... 508 Single returns ................................................................................. 508 Shipping ..........................................................................
Summary of the content on the page No. 18
xvi ENWW
Summary of the content on the page No. 19
List of tables Table 1-1 Sequence of operation ....................................................................................................................... 3 Table 1-2 Solenoids ........................................................................................................................................... 5 Table 1-3 Switches ............................................................................................................................................. 6 Table
Summary of the content on the page No. 20
Table 3-17 Causes and solutions for fuser delivery delay jams ..................................................................... 394 Table 3-18 Causes and solutions for wrapping jams ..................................................................................... 394 Table 3-19 Causes and solutions for fuser delivery stationary jams .............................................................. 395 Table 3-20 Causes and solutions for residual media jams ..................................