Summary of the content on the page No. 1
Wired / Wireless / PoE
CMOS IP Camera
ICA-107
ICA-107W
ICA-107P
User’s Manual
Version: 1.00
Summary of the content on the page No. 2
Copyright © 2007 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET. PLANET makes no representations or warranties, either expressed or implied, with respect to the contents hereof and s
Summary of the content on the page No. 3
R&TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE) The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8,2000. Safety This equipment is designed with the utmost c
Summary of the content on the page No. 4
Contents 1. Introduction.......................................................................................................... 1 2. Package Content................................................................................................. 2 3. System Requirement........................................................................................... 3 4. Hardware Installation........................................................................................... 4 4.1. LE
Summary of the content on the page No. 5
7.8.3. Status...........................................................................................................44 7.8.4. General ........................................................................................................46 7.8.5. About ...........................................................................................................47 7.9. Playback .................................................................................................................
Summary of the content on the page No. 6
1. Introduction Searching for a powerful and economical Internet Camera? PLANET is glad to introduce our ICA-107 / ICA-107W / ICA-107P. Those Internet Cameras Integrated a microcomputer and a high quality CMOS digital-Image-Sensor, enabling it to display high quality live streaming video over your LAN and the Internet. The motion detection of the ICA-107 series can notify users via email or ftp when detecting any movement. With its admin software, no expertise required, your first sur
Summary of the content on the page No. 7
2. Package Content Internet Camera Power Adapter Camera Stand Kit Category 5 Ethernet Cable Quick Installation Guide CD-Rom External Antenna (ICA-107W only) If any of the above items are missing, please contact your supplier. 2
Summary of the content on the page No. 8
3. System Requirement Model ICA-107 ICA-107W ICA-107P Network Environment Network Access 10/ 100Base-TX Ethernet - IEEE 802.11b/g IEEE 802.3af PoE Additional Interface Monitoring System Recommendation System Hardware • CPU: Pentium 4, 1.6GHz or above • Memory Size: 256 MB (512 MB Recommended) • VGA card resolution: 800 x 600 or above Web Browser • Internet Explorer 6.0 or above System Requirement for IP Camera Admin & Viewer Support OS Windows 2000 SP4, Windows XP SP2 System Ha
Summary of the content on the page No. 9
4. Hardware Installation 4.1. LED and Focusing The IP Camera head and its focus ring allow you to modify the aim and focus of the IP Camera. To adjust the IP Camera’s focus, please rotate the focus ring. There are LEDs indicating the IP Camera status and networking status. Power When the IP Camera is power on, the LED will light on. WLAN (ICA-107W only) When the IP Camera is linking with wireless interface, the LED will light on. This LED will flash when video is transmitting or
Summary of the content on the page No. 10
4.2. Hardware Connection Power Input The DC power input connector is located on the IP Camera's bottom panel, and is labeled 12V DC with a single jack socket to supply power to the IP Camera. Power will be generated when the power supply is connected to a wall outlet. Ethernet Jack The IP Camera's bottom panel features an RJ-45 connector for connections to 10Base-T Ethernet cabling or 100Base-TX Fast Ethernet cabling (which should be Category 5 twisted-pair cable). The port supports
Summary of the content on the page No. 11
Installation Procedure 1. Unpack the package and verify that all the items listed in the Chapter 2 are available. 2. Connect the IP Camera to your network with the attached network cable; please connect the IP camera to your network switch or router. 3. Connect the power adapter to IP Camera and plug the power adapter to power outlet. The IP Camera will be powered on. When the IP Camera is ready, the Power LED will light on. 4. Make sure that you have installed the ActiveX utility. N
Summary of the content on the page No. 12
5. Software Installation Follow the steps below to install the utilities. The following installation is implemented in Windows XP and the installation procedure is similar to Windows 2000. 1. Insert the CD shipped along with the IP Camera into your CD-ROM drive. The installation page should open with your default browser. If not, please double click on the “default.htm” in the CD. 2. Click on the hyperlink “Install Administrator Utility”. 7
Summary of the content on the page No. 13
3. After clicking on the “Install Administrator Utility” hyperlink, the browser should prompt to download the installation program. Click on the “Run” button, the installation program should be started. 4. Click “Next” to start the installation. 8
Summary of the content on the page No. 14
5. Click on the “Change” button to choose the destination you wished to install the utility. If no specific requirement, leave the default setting and click “Next”. 6. Click “Install” to start installing the utility. 9
Summary of the content on the page No. 15
7. The system will install the program automatically. 8. Click “Finish” to complete the software installation. 10
Summary of the content on the page No. 16
9. After the installation, IP Camera Admin will launch automatically. It will start to search the IP Cameras in your intranet and it will list all the available IP Cameras on the camera list. Choose the one that you would like to configure and click “Setting Wizard” to processed. Camera list 10. Please enter the default password “Admin” and click “OK” to login to the IP Camera’s setup page. 11
Summary of the content on the page No. 17
11. To let the IP Camera work, you should configure the IP Camera’s IP address as you want. The utility will try to find an available IP address and recommend you using that address. Besides work with the recommended IP, you may input the IP address manually. Please be aware that the IP address of the IP Camera must be in the same IP segment of your . Click “Finish” to apply the configuration. 12. After press “Finish”, the camera will restart. Please wait for a minute. Then you may
Summary of the content on the page No. 18
6. Using the IP Camera Admin The IP Camera Admin allows users to search and setup the cameras located within the Intranet. With the IP Camera Admin, users can view all the information about the selected IP Camera; furthermore, it provides a setting wizard, which can guide users to add the IP Camera to the network easily and promptly. There are two ways to run the IP Camera Admin: 1. Click “Start”, select “Programs”→“IP Camera” →”Admin Utility” to run the utility. 2. Double click the I
Summary of the content on the page No. 19
6.1. General Setting LAN Auto Discover The IP Camera Admin will search all the available IP Camera within the network when you click on this button. Camera List The name and setting status of the IP Camera will show in this list. The “ ” icon means the configuration of the IP Camera is in the status of factory default. The “ ” icon means the IP Camera has been configured before. The “ ” icon means the camera is unknown. Internet Add and Delete Button The functions located in thi
Summary of the content on the page No. 20
setting, etc. Camera Setting Detail Setting You might use this function for further configuring the IP Camera, such as IP address, Resolution, password and firmware upgrade, etc. Setting Wizard You might use this function to configure the camera name, IP address and the video port of the IP Camera. 15
