Streszczenie treści zawartej na stronie nr. 1
ENGLISH
OWNER’S MANUAL
LCD MONITOR
Please read this manual carefully before operating your set and
retain it for future reference.
LCD MONITOR MODEL
E1911T E1911S
E2211T E2211S
E2411T
www.lg.com
Streszczenie treści zawartej na stronie nr. 2
Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national stan
Streszczenie treści zawartej na stronie nr. 3
Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation. If these openings are blocked, built-up heat can cause failures wh
Streszczenie treści zawartej na stronie nr. 4
Important Precautions On Cleaning Unplug the display before cleaning the face of the display screen. Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display screen because over-spraying may cause electrical shock. When cleaning the product, unplug the power cord and scrub gently with a soft cloth to prevent scratching. Do not clean with a wet cloth or spray water or other liquids directly onto the product. An electric shock may occur. (Do not use chemicals such as benz
Streszczenie treści zawartej na stronie nr. 5
Accessories !!! Thank for selecting LGE products !!! Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Power Cord User's Guide/Cards 15-pin D-Sub Signal Cable DVI-D Signal Cable (To set it up, this signal cable may be (Only E1911T/E2211T/E2411T) attached to this product before (This feature is not available in all shipping out.) countries.) NOTE This accessories may look different from those shown here. User must use shielded si
Streszczenie treści zawartej na stronie nr. 6
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand 1. Place the monitor with its front facing downward on a soft cloth. 2. Assemble the Stand Body into the 3. Assemble the Stand Base(Front, product in the correct direction as shown in Rear) into the Stand Body in the the picture. Make sure you push it until you correct direction. hear it “click”. Hinge Body Stand Body Sta
Streszczenie treści zawartej na stronie nr. 7
Connecting the Display Disassembling the stand 2. Place the monitor face Down on the 1. Put a cushion or soft cloth on aflat cushion or soft cloth. surface. 3. Change your lock on the product as it follows and turn it in the arrow direction. .. If you can't release the stand base even the locking knob is at a release position, Please push the indicated knob down and retry it. 6
Streszczenie treści zawartej na stronie nr. 8
Connecting the Display 4. Pull out the Stand to remove. 5. Pushing the PUSH button, Take the stand body from hinge body. Good Position Bad Position Warning: You can hurt your finger. 7
Streszczenie treści zawartej na stronie nr. 9
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display -After installation, adjust the angle as shown below. 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5˚ to 15˚ Do not touch or press the screen when adjusting the angle of the monitor. When adjusting the angle of the screen, do not put your finger(s) in between the head of the
Streszczenie treści zawartej na stronie nr. 10
Connecting the Display E1911T/E2211T/E2411T Connecting with the PC 1. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. 2. Connect signal input cable and power cord in order, then tighten the screw 1 2 of the signal cable. A Connect DVI-D(Digital signal) Cable B Connect D-sub(Analog signal) Cable NOTE This is a simplified representation of the rear view. This rear view represents a general mod
Streszczenie treści zawartej na stronie nr. 11
Connecting the Display E1911S/E2211S Connecting with the PC 1. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. 2. Connect signal input cable and power cord in order, then tighten the screw 1 2 of the signal cable. A Connect D-sub(Analog signal) Cable NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as
Streszczenie treści zawartej na stronie nr. 12
Control Panel Functions Front Panel Controls E1911T/E2211T/E2411T E1911S/E2211S MENU Button OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear. You can unlock the OSD controls at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" should appear. 11
Streszczenie treści zawartej na stronie nr. 13
Control Panel Functions SUPER ENERGY Use this button to enter SUPER ENERGY SAVING menu.For more information, refer to page 18. SAVING Button AUTO Button AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press the AUTO button on the MONITOR SETUP OSD. (Only Analog Mode) This will automatically adjust your display image to the ideal settings for the current screen resolution size (display mode). The best display mode is E1911T/E1911S : 1366 x 768 E2211T/E2211S/E2411T: 1920 x 1080
Streszczenie treści zawartej na stronie nr. 14
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. To make adjustments in the On Screen Display, follow these steps: Press the discretionary Button, then
Streszczenie treści zawartej na stronie nr. 15
On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. : D-SUB(Analog signal) input DSUB DVI-D : DVI-D(Digital signal) input Main menu Sub-menu Supported input Description MENU To adjust the brightness of the DSUB BRIGHTNESS screen DVI-D To adjust the image size ORIGINAL RATIO COLOR TEMP To customize the color of the screen (PRESET / USER) To adjust the contrast of the CONTRAST screen LANGUAGE
Streszczenie treści zawartej na stronie nr. 16
On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears. Menu Name Icons Sub- menus Button Tip Exit Adjust (Decrease/Increase) Select another sub-menu Restart to select sub-menu NOTE OSD (On Screen Display) menu languages on the monitor may differ from t
Streszczenie treści zawartej na stronie nr. 17
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description To adjust the brightness of the screen. WIDE Switch to full screen mode according to input image signal. ORIGINAL Change the input image signal ratio to original. * This function works only if input resolution is lower than monitor ratio (16:9). Select the screen color. PRESET • WARM: Set the screen to warm color temperature . • MEDIUM: Set the screen to medium color temperature. • COOL: Se
Streszczenie treści zawartej na stronie nr. 18
On Screen Display(OSD) Selection and Adjustment Main menu Description To adjust the contrast of the screen. To choose the language in which the control names are displayed. Restore all factory default settings except "LANGUAGE." Press the , buttons to reset immediately. Exit : Exit , , : Move : Select another sub-menu 17
Streszczenie treści zawartej na stronie nr. 19
On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the SUPER ENERGY SAVING Button, then the main menu of the OSD appears. Menu Name Sub-menus Icons Button Tip Exit Move Restart to select sub-menu NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual. 18
Streszczenie treści zawartej na stronie nr. 20
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description Turn on the SUPER ENERGY ON SAVING fuction. When current setting value is ON,the SUPER SAVING color is green. OFF Turn off the SUPER ENERGY SAVING function.Now the monitor is LED SAVING function. When current setting value is OFF,the SUPER SAVING color is gray. Clear the TOTAL POWER RESET REDUCTION and TOTAL CO2 REDUCTION values. Exit : Exit , : Move : Select another sub-menu OK : Select TOTAL POWER REDUCTION : Ho
