Resumo do conteúdo contido na página número 1
Compaq Presario Desktop Products
Upgrading and
Servicing Guide
Resumo do conteúdo contido na página número 2
The information in this document is subject to change without notice. ® Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. HP shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. HP assumes no responsibility for the use or reliability o
Resumo do conteúdo contido na página número 3
table of contents upgrading and servicing the pc...................................................... 1 preparing the pc ............................................................................ 1 removing or upgrading a drive ...................................................... 2 locating drive positions..............................................................................3 removing a drive ....................................................................................
Resumo do conteúdo contido na página número 4
iv Upgrading and Servicing Guide
Resumo do conteúdo contido na página número 5
upgrading and servicing the pc This guide describes procedures for accessing the internal parts of the PC and installing components. NOTE: The procedures for the S0000 and 8000 series models are the same except where noted. disconnecting the power cord WARNING: To reduce the risk of personal injury from electrical shock and hot surfaces, disconnect the power cord from the wall outlet, and allow the internal system components to cool before IN touching. 5 Disconnect all e
Resumo do conteúdo contido na página número 6
removing the front bezel from the 8000 removing the pc access panel on the 8000 series series 8 Remove the front bezel by following the removing or upgrading a appropriate method for your PC model: drive • To remove the front bezel from the S0000 series model, gently pry the top section (1) of the Depending on your PC configuration, you may have bezel away from the chassis. On the inside of up to four of the following storage drives in your PC. the front bezel, pre
Resumo do conteúdo contido na página número 7
locating drive positions 1 Optical drive, may be a CD-ROM, CD-RW, DVD-ROM, or DVD+RW/+R drive 2 Second optical drive, may be a DVD-ROM, DVD+RW/+R, CD-ROM, CD-RW drive, or 7-In-1 memory card reader (select models only) 3 Diskette (floppy) drive 4 Hard disk drive disconnecting the optical drive cables disconnecting the 7-in-1 memory card reader cable drive positions on the S0000/8000 series (S0000 shown) removing a drive 1 Locate the drive you want to remove. 2 Compl
Resumo do conteúdo contido na página número 8
removing an optical or diskette drive from the 8000 series disconnecting the hard disk drive cables • To release a hard disk drive from the chassis of 4 Release the drive from the chassis by following the the 8000 series, slide the drive lock mechanism method appropriate for your PC model. (1) to unlock the drive in the drive bay, remove • To release a drive from the chassis of the S0000 the metal drive shield (2) by pressing and lifting series, lift the release tab (1) on
Resumo do conteúdo contido na página número 9
NOTE: If you have the S0000 series, and you removed a 7-In-1 memory card reader, continue to step 7; otherwise, you are finished with the task of removing a drive from the chassis. If you have the 8000 series and you removed a hard disk drive, a 7-In-1 memory card reader, or an optical drive, you are also finished with this task. If you have the 8000 series and you removed a diskette drive, continue to step 6. 6 For an 8000 series diskette drive, squeeze inward removing a 7-i
Resumo do conteúdo contido na página número 10
2 Slide the drive into the drive bay (1), making sure to align the guide screws with the guide slots, until it snaps into place. reconnecting the hard disk drive cables sliding the drive into the drive bay on the S0000/8000 (S0000 shown) 3 Reconnect the power and data cables to your drive as indicated in the following illustrations. reconnecting the optical drive cables NOTE: An optical drive for the 8000 series may include a sound cable. Connect this cable also. re
Resumo do conteúdo contido na página número 11
2 Press inward on each side of the bracket brace (3), 1 Complete the procedure described in “preparing and lower the bracket until it snaps into place over the pc” on page 1, but do not remove the front the diskette drive. Ensure that the guide screws (4) bezel. are installed in the adapter. 2 Locate the memory module inside your PC. See the 3 Return to “replacing or adding a drive” on page 5, following illustration for the location of the memory and begin with step 1. modules (1),
Resumo do conteúdo contido na página número 12
replacing or adding a memory module Upgrade the memory in your PC with memory of the same type and speed as the memory originally installed in your PC. CAUTION: When handling a memory module, be careful not to touch any of the contacts. Doing so may damage the module. 1 Open both latches of the memory module socket (1). installing a memory module 3 Complete the procedure described in “reassembling the pc” on page 10. NOTE: If a blank screen is displayed after replacing
Resumo do conteúdo contido na página número 13
to remove an expansion card 1 Complete the procedure described in “preparing the pc” on page 1, but do not remove the front bezel. • To remove an expansion card from the S0000 series, continue to step 2. • To remove an expansion card from the 8000 series, skip to step 3. 2 On the S0000 series, on the rear of the PC, remove the expansion bracket covering the expansion slots by removing the screw from the bracket cover (1), and then remove the expansion bracket cover (2). removin
Resumo do conteúdo contido na página número 14
1 • If you have an 8000 series, continue to step 2. • If you have an S0000 series, skip to step 3. 2 For the 8000 series, secure the expansion card to the chassis with the slot cover screw. 3 For both the S0000 and 8000 series, if you have replaced an expansion card, store the old card in the anti-static packaging that contained your new card. 2 • If you have an S0000 series, continue to step 4. • If you have an 8000 series, skip to step 5. 4 For the S0000 series, replace the expans
Resumo do conteúdo contido na página número 15
3 Reconnect the power cable (1) to the PC, and plug the cable into an electrical outlet (2). replacing the side access panel on the S0000 series reconnecting the power cable on the S0000/8000 (S0000 shown) 4 Reconnect the modem/telephone cable, if present. 5 Reconnect all peripheral devices to the PC. WARNING: To reduce the risk of electrical shock, fire, or damage to the equipment, do not plug telecommunications or telephone connectors into the network interface car
Resumo do conteúdo contido na página número 16
Printed in
