Руководство по эксплуатации Patton electronic G.SHDSL.BIS CPE WITH FIXED SERIAL INTERFACES 3088A

Краткое содержание страницы № 1

OnSite™ Model 3088A Series
G.SHDSL.bis CPE with Fixed
Serial Interfaces
Quick Start Guide
Important—This is a Class A device and is intended for use in a light industrial environment. It is not
intended nor approved for use in an industrial or residential environment.
REGULATORY MODEL NUMBER: 03340D4-001
Sales Office: +1 (301) 975-1000
Part Number: 07M3088A-QS, Rev. A
Technical Support: +1 (301) 975-1007
Revised: February 2, 2012 E-mail: support@patton.com
WWW: www.patton.com

Краткое содержание страницы № 2

• Do not open the device when the power cord is connected. For sys- tems without a power switch and without an external power adapter, line voltages are present within the device when the power cord is connected. WARNING • For devices with an external power adapter, the power adapter shall be a listed Limited Power Source The mains outlet that is utilized to power the device shall be within 10 feet (3 meters) of the device, shall be easily accessible, and protected by a circuit breaker in c

Краткое содержание страницы № 3

SWITCHING POWER SUPPLY MODEL : SYD1106-0505 INPUT : 36-60V 0.2A MAX OUTPUT : +5V 1.0A OUTPUT POWER : 5W MAX
: G01234567890 MADE IN CHINA BY SUNNY 1.0 Select configuration method Before powering up, you must select one of the following methods for configuring your OnSite: • Plug ‘n’ Play—The OnSite comes factory-configured for Plug ’n’ Play configuration when connected to a service-provider network.  DIP Switch—For deploying the OnSite in back-to-back

Краткое содержание страницы № 4

Link Activity TM / ERR Terminal DSL Power Figure 2. Model 3088A/CA front panel 2.3 Power up indication Verify that the Power LED (see figure 2) illuminates and remains lit. 3.0 Connect the G.SHDSL port 1. Obtain single-twisted-pair cable with an RJ-45 plug connector at each end. 2. Plug one end of the cable into the RJ-45 socket (labelled DSL) on the OnSite CPE. — If you are connecting to a DSL service, plug the other end of the cable into the RJ-45 wall socket that provides your G.SH

Краткое содержание страницы № 5

Connect the serial cable to the OnSite serial port as follows: 1. Attach the male connector of the serial cable to the female serial connector on the OnSite. 2. Attach the other end of the cable to the serial connector on the local serial CPE. Note You can connect the V.35 interface to an M/34 connector using Patton’s Model 2-34F25M interface adapter. Note You can configure the E1 interface to either recover the network clock from the E1 line or supply the network clock for the E1 line.

Краткое содержание страницы № 6

1.3 Industry Canada Notice This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is con- firmed by the registration number. The abbreviation, IC, before the registration number signifies that registra- tion was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment. This Declaration of Conformity means that the equipment meets

Краткое содержание страницы № 7

Die Sicherheitshinweise in der mitgelieferten Produktdokumentation sind zu beachten. Die Konformität mit der oben erwähnten Richtlinie wird durch das CE-Zeichen auf dem Gerät bestätigt. Die unterzeichnete Konformitätserklärung kann heruntergeladen werden von: www.patton.com/ certifications/. A.6 Authorized European Representative D R M Green European Compliance Services Limited. Oakdene House, Oak Road Watchfield, Swindon, Wilts SN6 8TD, UK Copyright statement Copyright © 201

Краткое содержание страницы № 8

Warranty, Trademark, & Compliance Information For warranty, trademark and compliance information, refer to the OnSite 3088A Getting Started Guide available online at www.patton.com/manuals/3088A.pdf. 8 Model 3088A Series Quick Start Guide