Bedienungsanleitung Dakota Digital SERIES II STR5D

Bedienungsanleitung für das Gerät Dakota Digital SERIES II STR5D

Gerät: Dakota Digital SERIES II STR5D
Kategorie: Autozubehör
Produzent: Dakota Digital
Größe: 0.29 MB
Datum des Hinzufügens: 5/30/2014
Seitenanzahl: 20
Anleitung drucken

Herunterladen

Wie kann man es nutzen?

Unser Ziel ist Ihnen einen schnellen Zugang zu Inhalten in Bedienungsanleitungen zum Gerät Dakota Digital SERIES II STR5D zu garantieren. Wenn Sie eine Online-Ansicht nutzten, können Sie den Inhaltsverzeichnis schnell durchschauen und direkt zu der Seite gelangen, auf der Sie die Lösung zu Ihrem Problem mit Dakota Digital SERIES II STR5D finden.

Für Ihre Bequemlichkeit

Wenn das direkte Durchschauen der Anleitung Dakota Digital SERIES II STR5D auf unserer Seite für Sie unbequem ist, können sie die folgende zwei Möglichkeiten nutzen:

  • Vollbildsuche – Um bequem die Anleitung durchzusuchen (ohne sie auf den Computer herunterzuladen) können Sie den Vollbildsuchmodus nutzen. Um das Durchschauen der Anleitung Dakota Digital SERIES II STR5D im Vollbildmodus zu starten, nutzen Sie die Schaltfläche Vollbild
  • Auf Computer herunterladen – Sie können die Anleitung Dakota Digital SERIES II STR5D auch auf Ihren Computer herunterladen und sie in Ihren Sammlungen aufbewahren. Wenn Sie jedoch keinen Platz auf Ihrem Gerät verschwenden möchten, können Sie sie immer auf ManualsBase herunterladen.
Dakota Digital SERIES II STR5D Handbuch - Online PDF
Advertisement
« Page 1 of 20 »
Advertisement
Druckversion

Viele Personen lesen lieber Dokumente nicht am Bildschirm, sondern in gedruckter Version. Eine Druckoption der Anleitung wurde ebenfalls durchdacht, und Sie können Sie nutzen, indem Sie den Link klicken, der sich oben befindet - Anleitung drucken. Sie müssen nicht die ganze Dakota Digital SERIES II STR5D Anleitung drucken, sondern nur die Seiten, die Sie brauchen. Schätzen Sie das Papier.

Zusammenfassungen

Unten finden Sie Trailer des Inhalts, der sich auf den nächsten Anleitungsseiten zu Dakota Digital SERIES II STR5D befindet. Wenn Sie den Seiteninhalt der nächsten Seiten schnell durchschauen möchten, können Sie sie nutzen.

Inhaltszusammenfassungen
Inhaltszusammenfassung zur Seite Nr. 1



SERIES II




VACUUM FLUORESCENT DIGITAL DASHBOARD




The latest in digital dashboard technology for the
street rodder, car, and truck enthusiast.





INSTALLATION AND OPERATION MANUAL


Please read this before beginning installation or wiring.




MODELS STR3D, STR4D, STR5D, & STR6D






3421 W. Hovland Ave.
Sioux Falls, SD 57107
Phone: (605) 332-6513
FAX: (605) 339-4106

Inhaltszusammenfassung zur Seite Nr. 2

Thank you for purchasing the Vacuum Fluorescent Digital Dashboard from DAKOTA DIGITAL, the leader in custom automotive electronics. Representing the latest electronics dashboard technology for the street rodder, car, and truck enthusiast alike, the digital instrumentation uses state of the art vacuum fluorescent display technology to give the driver up to date and accurate information on the operation of his or her vehicle. As used in several production automobiles, vacuum fluorescent d

Inhaltszusammenfassung zur Seite Nr. 3

WARNING The vacuum fluorescent displays are made of glass and should be handled with care. Use extreme care around the glass evacuation tubes (small tubes at the bottom of each display) as bumping them may cause breakage and render the display useless. MOUNTING DISPLAY SYSTEMS WITH SUBPANELS When mounting instrumentation systems mounted to a Lexan subpanel, begin by removing the subpanel from the aluminum. Cut an opening in the dash just smaller than the outer dimensions of the

Inhaltszusammenfassung zur Seite Nr. 4

MOUNTING KITS INTO ORIGINAL DASHES When installing the display system into the original bezel, several steps must be taken to prepare the bezel. The first is to remove the cluster from the dashboard and all instrumentation from the bezel. You should essentially be left with a bare chrome or metal bezel. Remove all felt inserts from the back side of the bezel that sit between the lens and the chrome. 55-56 Chevy car chrome bezel shown with lens and display opening outlines. Next, tak

Inhaltszusammenfassung zur Seite Nr. 5

Wiring the control box into the vehicle. +12V Connect the +12V terminal to accessory power from the fuse panel or vehicle wiring harness. This terminal should have power when the key is on or in accessory position. In addition to powering the display system, this is also where the voltmeter gauge senses the vehicle electrical system voltage. Use 20 AWG or larger wire to ensure the system gets good power. Never connect this to a battery charger alone. It needs to have a 12 volt batt

Inhaltszusammenfassung zur Seite Nr. 6

SPEED The vehicle speed sensor (VSS) connects to this to tell the system how fast the vehicle is moving. For two wire speed sensors, like the one Dakota Digital supplies with this system, the polarity of the wires does not matter. Connect one wire to ground and the other to the speed terminal. The speed sensor ground wire should be brought back to the control box to ensure a proper signal is received. Twisting the ground and signal wires around each other provides an additional lev

Inhaltszusammenfassung zur Seite Nr. 7

A single wire should be run from the terminal on top of the water sender to the control box terminal marked WATER. If your wiring harness already has a wire routed through the vehicle for the water temperature then it may be used. Do not route the water sender wire along side a spark plug wire or other high current or high voltage wires. Doing so can cause incorrect or erratic gauge readings. If the water display shows “---“ this indicates that the control box is sensing a short to grou

Inhaltszusammenfassung zur Seite Nr. 8

A single wire should be run from the fuel sender to the control box terminal marked FUEL. If your wiring harness already has a wire routed through the vehicle for the fuel sender then it may be used. If using a wire from an existing harness, make sure that the wire does not have power. The fuel sender gets power from the control box only. Fuel senders get their ground from the sender mounting plate. Make sure that a ground wire is connected from one of the sender mounting bolts to the

Inhaltszusammenfassung zur Seite Nr. 9

BRAKE The BRAKE terminal can be used as a brake system warning indicator. The BRAKE input is activated by a ground signal from the brake pressure switch on the master cylinder or from the parking brake set switch. Connect a wire from this terminal to the pressure switch on the master cylinder or consult a vehicle service manual to determine color and location of an existing wire. Whenever the BRAKE input is grounded the system will flash a “b” to the right of the speedometer.

Inhaltszusammenfassung zur Seite Nr. 10

MPH/KPH The MPH/KPH terminal is activated by a 12 volt signal from a push button or toggle switch(not supplied). When the display system is in English mode (MPH & °F) by placing DIP programming switch #7 off, applying 12 volts to this terminal will convert the speed reading from MPH to KPH. The odometer will continue to accumulate miles correctly, but will display dashes. The bar speed display, if present, will not be affected. When the display system is in Metric mode (KPH & °C) by

Inhaltszusammenfassung zur Seite Nr. 11

Insert cable with red stripe to right side. Optional display power connector found on some systems. 11

Inhaltszusammenfassung zur Seite Nr. 12

Setting up the control box SPEEDOMETER CALIBRATION The speedometer calibration is done using the TRIP and RESET switches. There are two different ways to calibrate the speedometer. The first method control box uses an auto-cal mode where you drive one mile (1 km for metric) and the system automatically adjusts the speedometer calibration. The second method allows you to adjust the speedometer up or down as you drive. To enter the auto-calibration mode, begin with the key off. Pres

Inhaltszusammenfassung zur Seite Nr. 13

TACHOMETER DIP SWITCH SETTINGS The control box will work with 4, 6, 8, and 10 cylinder ignition systems. The DIP programming switches are located inside the control box, so the cover must be carefully removed to get access to the switches. Make sure the key is turned off before opening up the control box so that there is no power to the system. The switches numbers 5 and 6 select the number of engine cylinders. The settings are as follows: Engine cylinders Switch #5 Switch #6 Bar ta

Inhaltszusammenfassung zur Seite Nr. 14

GAUGE WARNING FEATURE The gauges have the built in feature to alert you when they are outside their normal operation range. The fuel display will flash whenever the fuel level is below 10% to indicate low fuel. The voltage gauge will flash whenever the system voltage is below 11.0 volts and the engine is running. The water gauge will flash whenever the temperature is higher than the water warning set point. The oil gauge will flash whenever the oil pressure is below the oil warning se

Inhaltszusammenfassung zur Seite Nr. 15

WIRE COLOR CODE FOR GM WIRING HARNESS On the connector that originally plugged into the instrument cluster: Function Color ------------------------------------------------------------------- +12 volt Pink/Black or Pink Ground Black Oil sender Tan or no wire if mechanical Water sender Dark green Fuel sender Pink or light brown (should not have power) Left turn Light blue Right turn Dark blue High beam Light green Brake warn Tan/

Inhaltszusammenfassung zur Seite Nr. 16

TROUBLESHOOTING GUIDE This is a list of some problems and their solutions which may be encountered when installing your instrumentation system. If you cannot determine what the problem is or how to solve it, please call our technical assistance line (605) 332-6513 or email to dakotasupport@dakotadigital.com. * A note on vehicle grounding. * The most common cause of problems with electric gauges is poor ground connections. The engine block has the highest ground currents of any poin

Inhaltszusammenfassung zur Seite Nr. 17

Symptom Possible Problem Solution ----------------------------------------------------------------------------------------------------------------------------------- The tachometer reading The tachometer signal wire is Check the connections at both is incorrect. loose or broken. ends of the wire. The control box is not set up for Refer to the Internal Adjustments the proper number of cylinders section of the installation manual or the proper tach range.

Inhaltszusammenfassung zur Seite Nr. 18

Symptom Possible Problem Solution ----------------------------------------------------------------------------------------------------------------------------------- The fuel display reads The control box may be set for Refer to “Fuel DIP switch settings” backwards, incorrectly, the wrong type of fuel sender. section of the installation manual or does not change. to ensure that the settings match your fuel sender. The fuel sender may not be Check th

Inhaltszusammenfassung zur Seite Nr. 19

Symptom Possible Problem Solution ----------------------------------------------------------------------------------------------------------------------------------- The gear shift indicator The optional gear shift sending Connect the sending unit to the does not light up. unit is not connected to the control box using the control box. instructions supplied with the sending unit. The gear shift indicator The gear shift sending unit Check the connection

Inhaltszusammenfassung zur Seite Nr. 20

CLOCK Wiring instructions for VFD systems with a clock built in. Introduction: The clock displays the current time in 12 hour format with an AM/PM indicator. The AM/PM indicator appears as a dot that will be displayed in the upper left corner. The dot will be on every other 12 hour period (on during AM and off during PM). The high brightness display matches our other Odyssey and STR series gauges and has the same night brightness dimming capability. Features included are: • Quartz


Ähnliche Anleitungen
# Bedienungsanleitung Kategorie Herunterladen
1 Dakota Digital 3X Handbuch Autozubehör 14
2 Dakota Digital DHC-2100 Handbuch Autozubehör 6
3 Dakota Digital DHC-2000 Handbuch Autozubehör 8
4 Dakota Digital LED Tail Light Flasher LAT-NLF Handbuch Autozubehör 3
5 Dakota Digital LED Tail Lights for 1956 Chevy Car LAT-NR200 Handbuch Autozubehör 2
6 Dakota Digital LAT-NR162 Handbuch Autozubehör 0
7 Dakota Digital LAT-NR271 Handbuch Autozubehör 0
8 Dakota Digital LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne LAT-NR241 Handbuch Autozubehör 3
9 Dakota Digital LED Tail Lights for 1968 Chevelle LAT-NR180 Handbuch Autozubehör 1
10 Dakota Digital FFW-447 Handbuch Autozubehör 0
11 Dakota Digital LED Tail Lights for 1965 Nova LAT-NR130 Handbuch Autozubehör 0
12 Dakota Digital LED Tail Lights for 1955 Chevy Car LAT-NR190 Handbuch Autozubehör 0
13 Dakota Digital LED Tail Lights for 1968 Impala LAT-NR251 Handbuch Autozubehör 0
14 Dakota Digital LED Tail Lights for 1969 Firebird LAT-NR291 Handbuch Autozubehör 0
15 Dakota Digital LED Tail Lights for 1971 Bel Air LAT-NR390 Handbuch Autozubehör 0
16 Sony RM-X32 Handbuch Autozubehör 2
17 Sony MV-100CAR Handbuch Autozubehör 1
18 Sony DC-FX1 Handbuch Autozubehör 0
19 Sony RM-X33 Handbuch Autozubehör 13
20 Sony RM-X38 Handbuch Autozubehör 3