Bedienungsanleitung Char-Broil PATIO BISTRO 11601559

Inhaltszusammenfassung zur Seite Nr. 1

assembly
guide
Model Numbers:
11601514
11601559
11601578
Estimated time required for assembly: 1 Hour
ELECTRIC
(English)
42804382 • 6/02/10

Inhaltszusammenfassung zur Seite Nr. 2

2 A, B, C, Assembly: ASSEMBLY GUIDE CAUTION: For your safety, before operating, Read Product Guide & Outdoor Cooking Guide provided with this grill. *SAFETY First…..Grill components may have sharp edges. Be careful when handling grill parts during assembly. We suggest that you wear a sturdy pair of leather gloves while handling the grill parts. BEFORE You begin assembly of your grill…. 1. Carefully remove all components from the carton. 2. Familiarize yourself with the components

Inhaltszusammenfassung zur Seite Nr. 3

3 Grill Parts Diagram ASSEMBLY GUIDE H F D w A Q O V G X R B I B E K L C N P J S U U T M Key Qty Description Key Qty Description Key Qty Description M 1 Grease Tray --- 1 Hardware Pack A 1 Grill Lid N 2 Hubcap --- 1 Assembly Guide, English B 1 Lower Body O 1 Warming Rack — 1 Assembly Guide, Spanish, optional C 1 Controller P 2 Axle — 1 Assembly Guide, French, optional D 1 Element Assembly Q 1 Heat Indicator — 1 Product Guide, English E 1 Wire Shelf R 1 Cooking Grate — 1 Product Guide, Spanish

Inhaltszusammenfassung zur Seite Nr. 4

4 ASSEMBLY GUIDE GRILL CART Assembly Fasteners Part Qty A1– 1 Cart Base . A2– 1 Front Leg Set A3– 1 Rear Leg Set 2 A4– Wheels Wheel Retaining 2 A5– Hubcap Clip 1/4x20-1/2" 3/8-16 Nut (qty 2) screw (qty 2) (qty 4) Step 1– Attach Front Leg Set (A2) to the Cart Base (A1) using 2 1/4-20 screws. Attach Rear Axle Bolt Leg Set (A3) to the Cart Base (A1) in the (qty 2) same manner, using 2 1/4-20 screws. After cart assembly, if your cart doe

Inhaltszusammenfassung zur Seite Nr. 5

5 ASSEMBLY GUIDE GRILL CART Assembly Fasteners Part Qty . – A6 1 Cart Bracket 1 A7– Wire Shelf – A8 Leg End Cap 2 1/4x20-2" screw (qty 4) 1/4-20 Nut 1/4-20 Nut (qty 4) #10x3/8" screw (qty 2) Step 3 - Carefully turn the Cart Assembly over and allow it to rest on the tops of the leg assemblies. Spread the leg assemblies apart just far enough to allow the insertion of the Wire Shelf (A7) into the 4 leg holes. Assemble the Cart Bracket (A6) to the Cart Assembly

Inhaltszusammenfassung zur Seite Nr. 6

6 GRILL BODY Assembly ASSEMBLY GUIDE Fasteners Part Qty. B1– Lower Body 1 B2– Wind Shield 1 10-24x3/8" screw B3– Grill Lid 1 (qty 3) 10-24 Nut Fiber Washer 1/4-20 Nut 1/4-20x3/4" (qty 10) (qty 5) (qty 2) Hinge screw ASSEMBLY (qty 2) Step 1 - Attach the Lower Body Assembly (B1) to the Cart Assembly by aligning the studs on the bottom of the Step 3 - Attach the Wind Shield (B2) to the Lower Body (B1) grill with the corresponding holes in the tops of t

Inhaltszusammenfassung zur Seite Nr. 7

7 GRILL FINAL Assembly ASSEMBLY GUIDE Part Qty. NOTE: The Cooking Grate may have sharp edges. Be very careful C1 – Cooking Grate 1 when handling the Cooking Grate. C2 – 1 Warming Rack You should wear gloves when C3 – Grease tray 1 handling the Cooking Grate. Step 1 - With the Grill Lid open, place the Cooking Grate (C1)into the Lower Body, allowing it to rest on the three brackets spaced around the Lower Body. Be sure the slots in the Cooking Grate are facing the

Inhaltszusammenfassung zur Seite Nr. 8

8 GRILL FINAL Assembly ASSEMBLY GUIDE Part Qty. Fasteners C4 – Controller 1 10-24x3/8" C5 – Lid Handle 1 Fiber Washer screw (qty 2) (qty 2) NOTE: Be sure to press the controller into the receptacle as far as it will go. Route the controller cord BEHIND the towel bar as shown. Step 1 - Install the Controller (C4) into the receptacle. Be sure to route the controller cord behind the towel bar when installing the controller. The control knob should be facing up as